Preparation of Electroless Nickel-Phosphorous-TiO₂ Composite Coating for Improvement of Wear and Stress Corrosion Cracking Resistance of AA7075 in 3.5% NaCl

Abstract:

In this study nanoTiO₂ particles were incorporated into the electroless plating solution to prepare Ni-P-TiO₂ composite coating on anodized AA7075 aluminum alloy to improve the wear and stress corrosion cracking resistance of the coated alloy in 3.5%NaCl solution. The anodized AA7075 aluminum alloy was also performed by a boiling water sealing treatment for comparison. The wear and stress corrosion cracking (SCC) characteristics were investigated using a self-designed block-on-ring machine and slow strain rate test. The effect of corrosion was evaluated by electrochemical polarization measurements. The surface morphology, element composition and surface hardness of the coating were analyzed by scanning electron microscopy (SEM), X-ray energy dispersive spectrometry (EDS) and Vicker′s hardness tester. Experimental results indicated that after boiling water sealing treatment the resistance properties of the anodized AA7075 aluminum alloy were further improved. The anodizing treatment of AA7075 aluminum alloy gave a thick film with high porosity. The porous film efficiently improved the cohesion, adhesion and hardness of the electroless Ni-P composite coating. Therefore, the electroless Ni-P composite coating deposited on the anodized AA7075 aluminum alloy offered a superior wear, pitting corrosion and stress corrosion cracking resistance properties than both anodizing and sealing treatment. By comparison with Ni-P and Ni-P-TiO₂ coatings the incorporation of TiO₂ resulted in a more uniform and crack-free surface structure of the composite coating. This is responsible for the higher hardness, better wear, pitting corrosion and stress corrosion cracking resistance of the electroless Ni-P-TiO₂ coating.

• Periodical: Key Engineering Materials (Volumes 656-657)
• Pages: 74-79
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.656-657.74
• Online since: July 2015
• Authors: Cheng Kuo Lee, Chung Sheng Chang, An Hung Tan, Ching Yi Yang, Sheng Long Lee
• Keywords: AA7075 Alloy, Corrosion, Electrochemical Polarization, Electroless Ni-P, SCC, SSRT

References

[1] H.L. Liao, J.C. Lin, S.L. Lee, Effect of pre-immersion on the SCC of heat-treated AA7050 in an alkaline 3. 5%NaCl, Corros. Sci. 51 (2009) 209–216.

DOI: 10.1016/j.corsci.2008.10.037

[2] J.F. Li, Z.W. Peng, C.X. Li, Z.Q. Jia, W.J. Chen, Z.Q. Zheng, Mechanical properties, corrosion behaviors and microstructures of 7075 aluminium alloy with various aging treatments, Trans. Nonferrous Met. Soc. China 18 (2008) 755-762.

DOI: 10.1016/s1003-6326(08)60130-2

[3] B.M. Cina, US patent 3, 856, 584 (1974).

[4] Murat Baydo˘gan, Hüseyin Çimeno˘glu, E. Sabri Kayalı, A study on sliding wear of a 7075 aluminum alloy, Wear 257 (2004) 852-861.

DOI: 10.1016/j.wear.2004.05.006

[5] C.K. Lee, Susceptibility to stress corrosion cracking and electrochemical behavior of electroless Ni-P/nano-TiO2 composite coatings on 70-30 brass in fluoride solutions, Int. J. Electrochem. Soc. 7 (2012) 12941-12954.

DOI: 10.1016/s1452-3981(23)18011-4

[6] M. Novák, D. Vojtěch, T. Vitů, Influence of heat treatment on tribological properties of electroless Ni-P and Ni-P-Al2O3 coatings on Al-Si casting alloy, Appl. Surf. Sci. 256 (2010) 2956-2960.

DOI: 10.1016/j.apsusc.2009.11.057

[7] T.S.N. Sankara Narayanan, I. Baskaran, K. Krishnaveni, S. Parthiban, Deposition of electroless Ni–P graded coatings and evaluation of their corrosion resistance, Surf. Coat. Technol. 200 (2006) 3438-3445.

DOI: 10.1016/j.surfcoat.2004.10.014