Computer-Aided Modelling of a Latch Die Cutting in Deform - 2D Software System

Sergey Zvonov; Yury Klochkov

doi:10.4028/www.scientific.net/KEM.685.811

Paper Titles

Chemical Reaction Front Propagation between Inert Materials with Different Properties Taking into Account the Reagent Melting
p.789

Influence of Mineral Salts on the Production of Antibiotics Phenazine Series from Pseudomonas Aeruginosa
p.794

Synthesis and Study of Norfloxacin Labeled with Technecium-99m as a Potential Imaging Agent of Bacterial Inflammations
p.798

Reliability Model of Fault-Tolerant Dual-Disk Redundant Array
p.805

Computer-Aided Modelling of a Latch Die Cutting in Deform - 2D Software System
p.811

Simulation of Multidimensional Non-Linear Processes Based on the Second Order Fuzzy Controller
p.816

Information Technologies in Industrial Enterprises Production Assets Management
p.823

Adaptive Algorithm of Sensor Polling for Device Used for the Dam Condition's Diagnostics
p.828

Development of Intelligent Algorithm for Positioning a Vehicle on a Route
p.833

HomeKey Engineering MaterialsKey Engineering Materials Vol. 685Computer-Aided Modelling of a Latch Die Cutting in...

Computer-Aided Modelling of a Latch Die Cutting in Deform - 2D Software System

Abstract:

The article discusses theoretic foundations and parameters of a latch die cutting process modelled in the software system Deform - 2D. The analysis concerns standard methods of latch cutting which causes the excessive edge deformation (over 10% of a sheet thickness) that does not meet the customers' requirements.

You might also be interested in these eBooks

High Technology: Research and Applications 2015

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 685)

Pages:

811-815

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.685.811

Citation:

Cite this paper

Online since:

February 2016

Authors:

Sergey Zvonov*, Yury Klochkov

Keywords:

Die, Die Cutting, Matrix, Modelling, Thickness, Tool, Wedge-Shaped Edge

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] H.K. Tönshoff, C. Arendt, R. Ben Amor, Cutting of Hardened Steel, Manufacturing Technology. 49 (2000) 547–566.

DOI: 10.1016/s0007-8506(07)63455-6

Google Scholar

[2] J. D. Thiele, S. N. Melkote, Effect of Cutting-Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel, J. Manuf. Sci. Eng. 122 (1999) 642-649.

DOI: 10.1115/1.1286369

Google Scholar

[3] K. Nakayama, M. Arai, T. Kanda, Machining Characteristics of Hard Materials, Manufacturing Technology 37 (1988) 89-92.

DOI: 10.1016/s0007-8506(07)61592-3

Google Scholar

[4] T. I. El-Wardany, H. A. Kishawy, M. A. Elbestawi, Surface Integrity of Die Material in High Speed Hard Machining, J. Manuf. Sci. Eng. 122 (1999) 620-631.

DOI: 10.1115/1.1286367

Google Scholar

[5] W. König, M. Klinger, R. Link, Machining Hard Materials with Geometrically Defined Cutting Edges, Field of Applications and Limitations 39 (1999) 61-64.

DOI: 10.1016/s0007-8506(07)61003-8

Google Scholar