Investigation on Hardening and Softening Behavior of Steel after Rapid Strain Rate Changes

Abstract:

The design of industrial hot metal forming processes nowadays is mostly carried out using commercial Finite Element (FE) software codes. For precise FE simulations, reliable material properties are a crucial factor. In bulk metal forming, the most important material property is the materials flow stress, which determines the form filling and the necessary forming forces. At elevated temperatures, the flow stress of steels is determined by strain hardening, dynamic recovery and partly by dynamic recrystallization, which is dependent on strain rate and temperature. To simulate hot forming processes, which are often characterized by rapidly changing strain rates and temperatures, the flow stress is typically derived from flow curves, determined at arbitrary constant temperatures and strain rates only via linear interpolation. Hence, the materials instant reaction and relaxation behavior caused by rapid strain rate changes is not captured during simulation. To investigate the relevance of the relaxation behavior for FE simulations, trails with abrupt strain rate change are laid out and the effect on the material flow stress is analyzed in this paper. Additionally, the microstructure evolution due to the strain rate change is investigated. For this purpose, cylinder compression tests of an industrial case hardening steel are conducted at elevated temperatures and different strain rates. To analyze the influence of rapid strain rate changes, changes by one power of ten are performed at a strain of 0.3. As a reference, flow curves of the same material are determined at the initial and final constant strain rate. To investigate the microstructure evolution, compression samples are quenched at different stages, before and after the strain rate change. The results show that the flow curves after the strain rate change tend to approximate the flow curves measured for the final strain rate. However, directly after the strain rate change significant differences between the assumed instant flow stress and the real material behavior can be observed. Furthermore, it can be shown that the state of dynamic recrystallization at the time of the strain rate change influences the material response and relaxation behavior resulting in different slopes of the investigated flow curves after the strain rate change.

• Periodical: Key Engineering Materials (Volume 716)
• Pages: 121-128
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.716.121
• Online since: October 2016
• Authors: Jens Dierdorf*, Johannes Lohmar, Gerhard Hirt
• Keywords: Hot Deformation, Measurement, Micro Structure, Steel, Stress

References

[1] G.E. Dieter, Hot Compression Testing: Chapter 6, in: G.E. Dieter, H.A. Kuhn, S.L. Semiatin (Eds. ), Handbook of Workability and Process Design, ASM International, 2003, p.61–67.

[2] C. Zener, J.H. Hollomon, Effect of Strain Rate upon Plastic Flow of Steel, J. Appl. Phys. 15 (1944) 22–32.

DOI: 10.1063/1.1707363

[3] A. Laasraoui, J.J. Jonas, Prediction of steel flow stresses at high temperatures and strain rates, Metall. Mater. Trans. A 22 (1991) 1545–1558.

DOI: 10.1007/bf02667368

[4] B. Wietbrock, W. Xiong, M. Bambach, G. Hirt, Effect of Temperature, Strain rate, Manganese and Carbon Content on flow Behavior of three Ternary Fe-Mn-C (Fe-Mn23-C0. 3, Fe-Mn23-C0. 6, Fe-Mn28-C0. 3) High-Manganese Steels, Steel Res. Int. 82 (2011).

DOI: 10.1002/srin.201000248

[5] V. Maier, K. Durst, J. Mueller, B. Backes, H.W. Höppel, M. Göken, Nanoindentation strain-rate jump tests for determining the local strain-rate sensitivity in nanocrystalline Ni and ultrafine-grained Al, J. Mater. Res. 26 (2011) 1421–1430.

DOI: 10.1557/jmr.2011.156

[6] K. Graetz, C. Miessen, G. Gottstein, Analysis of steady-state dynamic recrystallization, Acta Mater. 67 (2014) 58–66.

DOI: 10.1016/j.actamat.2013.12.005

[7] E. Karimi, A. Zarei-Hanzaki, M.H. Pishbin, H.R. Abedi, P. Changizian, Instantaneous strain rate sensitivity of wrought AZ31 magnesium alloy, Mater. Des. 49 (2013) 173–180.

DOI: 10.1016/j.matdes.2013.01.068

[8] M.V. Rastegaev, New method of uniform upsetting of specime coefficient of external friction (in russian), Zavo. Lab. 3 (1940) 354–355.

[9] W. Xiong, J. Lohmar, M. Bambach, G. Hirt, A new method to determine isothermal flow curves for integrated process and microstructural simulation in metal forming, Int. J. Mater. Form. 8 (2015) 59–66.

DOI: 10.1007/s12289-013-1147-6

[10] DIN Deutsches Institut für Normung e.V., DIN EN ISO 643: Stahl – Mikrophotographische Bestimmung der erkennbaren Korngröße, Beuth Verlag, Berlin ICS 77. 040. 99, (2013).

DOI: 10.31030/1941325

[11] C.M. Sellars, G.J. Davies (Eds. ), Proceedings of the Conference on Hot Working and Forming Processes, The Society, London, (1979).