Experimental Study on Electro-Discharge Machining of Nickel-Based Superalloy

Yan Li; Jin Juan Fu; Li Guang Yang

doi:10.4028/www.scientific.net/KEM.723.51

Paper Titles

The Natural Aging Effect on the Activation Energy of the Precipitation Processes in the Al-Mg-Si Alloy
p.27

Principles of Optimal Control in the Synthesis of Composite Materials
p.32

Annealing Effect for Cold Rolling 6016 Aluminum Alloy Sheet
p.37

The Effect of Lack-of-Fusion Porosity on Fatigue Behavior of Additive Manufactured Titanium Alloy
p.44

Experimental Study on Electro-Discharge Machining of Nickel-Based Superalloy
p.51

The Effect of Modifying Agents on the Mechanical Properties of Straw Flour/Waste Plastic Composite Materials
p.56

Simulation on Temperature Field of Friction Stir Welding of 2A14 Aluminum Alloy Based on Equivalent Film Method
p.62

Toughening Mechanism and Mechanical Properties Simulation of Rubber-Toughened Polymers
p.68

The Influence of Different Wood Aggregates on the Properties of Geopolymer Composites
p.74

HomeKey Engineering MaterialsKey Engineering Materials Vol. 723Experimental Study on Electro-Discharge Machining...

Experimental Study on Electro-Discharge Machining of Nickel-Based Superalloy

Abstract:

The present work attempts to study the effect of important process parameters on material removal rate in electro-discharge machining of nickel-based superalloy. Experiments based on orthogonal array were conducted. Contents of peak current, pulse on time, duty cycle, and servo voltage were the main factors, and each factor was endowed three levels. Range analysis was used to investigate the orthogonal test on material removal rate, and a set of appropriate parameters were found. Confirmation test was conducted to validate the analysis and it can be seen that the predicted values show good agreement with the experimental results. The outcome of the present research work will be a considerable aid to industries for efficiency improvement in processing using EDM.

You might also be interested in these eBooks

View Preview

Proceedings of International Conference on Material Science and Engineering 2016

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 723)

Pages:

51-55

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.723.51

Citation:

Cite this paper

Online since:

December 2016

Authors:

Yan Li*, Jin Juan Fu, Li Guang Yang

Keywords:

Electrical Discharge Machining (EDM), Material Removal Rate, Nickel-Based Superalloy

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] B. S. Yilbas, H. Ali, N. Al-Aqeeli, et al., Laser treatment of Inconel 718 alloy and surface characteristics, Opt. Laser Technol. 78 (2016) 153-158.

DOI: 10.1016/j.optlastec.2015.11.006

Google Scholar

[2] N. S. Qu, Q. L. Zhang, X. L. Fang, et al., Experimental investigation on electrochemical grinding of Inconel 718, Procedia CIRP, 35 (2015) 16-19.

DOI: 10.1016/j.procir.2015.08.055

Google Scholar

[3] N. M. Abbas, D. G. Solomon, M. F. Bahari, A review on current research trends in electrical discharge machining (EDM), Int. J. Mach. Tools Manuf. 47(7-8) (2007) 1214-1228.

DOI: 10.1016/j.ijmachtools.2006.08.026

Google Scholar

[4] K. P. Rajurkar, M. M. Sundaram, A. P. Malshe, Review of electrochemical and electro discharge machining, Procedia CIRP, 6 (2013) 13-26.

DOI: 10.1016/j.procir.2013.03.002

Google Scholar

[5] S. Plaza, J. A. Sanchez, E. Perez, et al., Experimental study on micro EDM-drilling of Ti6Al4V using helical electrode, Precis. Eng. 38(4) (2014) 821-827.

DOI: 10.1016/j.precisioneng.2014.04.010

Google Scholar

[6] L. Gu, L. Li, W. S. Zhao, et al., Electrical discharge machining of Ti6Al4V with a bundled electrode, Int. J. Mach. Tools Manuf. 53(1) (2012) 100-106.

DOI: 10.1016/j.ijmachtools.2011.10.002

Google Scholar

[7] M. Manohara, T. Selvarajb, D. Sivakumara, et al., Experimental study to assess the effect of electrode bottom profiles while machining Inconel 718 through EDM Process, Procedia Mater. Sci. 6 (2014) 92-104.

DOI: 10.1016/j.mspro.2014.07.011

Google Scholar

[8] F. Klocke, D. Welling, A. Klink, et al., Evaluation of advanced wire-EDM capabilities for the manufacture of fir tree slots in Inconel 718, Procedia CIRP. 14 (2014) 430-435.

DOI: 10.1016/j.procir.2014.03.039

Google Scholar

[9] C. J. Li, Y. Li, H. Tong, et al., Thinning process of recast layer in hole drilling and trimming by EDM, Procedia CIRP, 42 (2016) 575-579.

DOI: 10.1016/j.procir.2016.02.262

Google Scholar