Obtaining Intermetallic Compound Copper-Tin: Plasma Dynamic Synthesis and Spark Plasma Sintering

Abstract:

The intermetallic compound tin-copper (Cu-Sn) is widely used in the creation of high-quality bearings, electric conductive lubricants, 3D printers. However, when connecting two metals, the bond between atoms in the lattice becomes covalent or ionic. This leads to the fact that the material becomes more brittle. Additionally, the production of intermetallic compounds is cost-based in terms of both material resources and money. In this paper, the ceramics has been sintered based on the intermetallic copper-tin powders, obtained by plasma dynamic method. The raw powdered materials based on Cu-Sn were obtained using a coaxial magnetoplasma accelerator with copper electrodes by adding the crushed tin into the accelerator. Using X-ray diffractometry (XRD) and transmission electron microscopy (TEM) analyses, the presence of such phases as copper Cu and tin-copper Cu41Sn11 in the obtained material has been confirmed. Further, such-synthesized powdered products were used to obtain bulk samples using the spark plasma sintering technology at various sintering parameters. Images from scanning electron microscope showed a uniform sintering of the product at the sintering temperature of 440 °C under a pressure of 60 MPa. It was found that the sintered intermetallic ceramics has the Vickers hardness equal to 120 Hv. The obtained sample has the lower friction coefficient and the smaller wear area in comparison with the sample, made of pure copper.

• Periodical: Key Engineering Materials (Volume 743)
• Pages: 25-30
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.743.25
• Online since: July 2017
• Authors: Alexander Sivkov, Alexander Ivashutenko, Yuliya Shanenkova, Ivan Shanenkov, Yuliya Polovinkina*
• Keywords: Coaxial Magnetoplasma Accelerator, Copper, Friction Coefficient, Hardness, Spark Plasma Sintering, TiN

References

[1] Lebedev O.V. i dr. Sistemy, metody, tehnologii, Nauchnyj zhurnal Bratskogo gosudarstvennogo universiteta. T. 2 (2009) 20-23.

[2] K. D. Kepler, J. T. Vaughey, M. M. Thackeray, Copper–tin anodes for rechargeable lithium batteries: an example of the matrix effect in an intermetallic system , Journal of Power Sources. T. 81 (1999) 383.

DOI: 10.1016/s0378-7753(99)00111-1

[3] J. Wolfenstine et al. Nano-scale Cu 6 Sn 5 anodes, Journal of power sources. T. 109 (2002) № 1, 230.

[4] L. Y. Beaulieu et al. Reaction of Li with alloy thin films studied by in situ AFM, Journal of The Electrochemical Society. T. 150 (2003) № 11, A1457-A1464.

DOI: 10.1149/1.1613668

[5] V. B. Tarel'nik, V. S. Marcinkovskij, A. V. Dzjuba, Novyj sposob uluchshenija prirabatyvaemosti pary trenija vkladysh podshipnika–shejka vala, J. Kompressornoe i jenergeticheskoe mashinostroenie. (2013) № 1, 49-53.

[6] X. Guo et al. Investigation of the microstructure and tribological behavior of cold-sprayed tin-bronze-based composite coatings, J. Applied Surface Science. T. 255 (2009) № 6, 3822-3828.

DOI: 10.1016/j.apsusc.2008.10.041

[7] A. Sivkov, Y. Shanenkova, A. Saigash, I. Shanenkov, High-speed thermal plasma deposition of copper coating on aluminum surface with strong substrate adhesion and low transient resistivity, J. Surface and Coatings Technology. 292 (2016) 63-71.

DOI: 10.1016/j.surfcoat.2016.03.029