Modification of Microstructure and Tensile Property of Sintered Fe-Cr-Mo-C Steel by Nickel Addition

Abstract:

Nickel is one of the alloying elements promoting the formation of acicular ferrite at the expense of proeutectoid ferrite. The Ni addition reduces the steady-state nucleation rates of grain boundary ferrite allotriomorph in Fe-C-Ni alloys. Due to such reasons, Ni was added to modify the microstructure of the sintered steel, investigated in this study, with the aim of improved mechanical properties. The sintered steel, produced from pre-alloyed Fe-Cr-Mo powder mixed with 0.3 wt.% C, was modified by Ni addition and cooling rate. The alloy compositional change was performed additions of varied Ni contents of 1.0, 1.5, 2.0, 2.5 and 3.0 wt.%. The material processing variables were investigated by using two different cooling rates of 0.1 and 5.4 °Cs^-1. Under the cooling rate of 0.1 °Cs^-1, the sintered Fe-Cr-Mo-3C steel without Ni addition showed dual-phase microstructure consisting of ferrite (soft phase) and bainite (hard structure). With Ni additions, the dual-phase microstructure was replaced by bainitic structure. Microstructural heterogeneity was observed due to the presence of Ni-rich areas, which increased with increasing added Ni contents. Under the cooling rate of 5.4 °Cs^-1, the sintered Fe-Cr-Mo-3C steels with and without Ni additions showed bainitic structure. Microstructural heterogeneity was similar to that of slowly cooled steel. Ni additions not only modified the sintered steel microstructure but increased tensile strength and elongation. In general, Ni pushes the C-curve of pearlite transformation to the right hand side and lowers the martensite start temperature. The absence of ferrite from the sintered steel with only 1 wt.% Ni addition and slowly cooled at 0.1 °Cs^-1 suggests that Ni strongly suppresses the austenite → ferrite transformation. In another word, Ni promotes bainite formation in the sintered Fe-Cr-Mo-Ni-C steels.

• Periodical: Key Engineering Materials (Volume 751)
• Pages: 42-46
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.751.42
• Online since: August 2017
• Authors: Nattaya Tosangthum, Monnapas Morakotjinda, Rungtip Krataitong, Pongsak Wila, Thanyaporn Yodkaew, Ruangdaj Tongsri*
• Keywords: Bainite, Fe-Cr-Mo-Ni-C Steel, Ferrite, Phase Transformation

References

[1] E.C. Bain, Functions of the Alloying Elements in Steel, American Society for Metals, (1939).

[2] Y. Yu, Thermodynamic and kinetic behaviours of Astaloy CrM, Proceedings of Powder Metallurgy World Congress, (2000).

[3] E. Lichanska, M. Sulowski, and A. Cias, Mechanical Properties and Microstructure of PM Mn-Cr-Mo Steels With Low Carbon Concentration, Arch. Metall. Mater., 61 (2016) 109-114.

DOI: 10.1515/amm-2016-0021

[4] M. Sulowski, A. Cias, and T. Pieczonka, The microstructure and properties of low carbon PM Cr-Mo steels sintered under different conditions, Arch. Metall. Mater., 59 (2014) 575-580.

DOI: 10.2478/amm-2014-0095

[5] W. Kiatdherarat, P. Mungsantisuk, S. Mahathanabodee, K. Sirivedin, R. Krataitong, M. Morakotjinda, T. Yotkaew, N. Tosangthum, R. Tongsri, Effects of cooling rate and carbon content on mechanical property of sintered Fe-Cr-Mo alloys, Key Eng. Mater., 658 (2015).

DOI: 10.4028/www.scientific.net/kem.658.69

[6] W. Srijampan, A. Wiengmoon, M. Morakotjinda, R. Krataitong, T. Yotkaew, N. Tosangthum, R. Tongsri, Microstructure and mechanical property of sintered Fe-Cr-Mo steels due to phase transformations with fast cooling rates, Mater. Design, 88 (2015).

DOI: 10.1016/j.matdes.2015.09.030

[7] W. Srijampan, M. Morakotjinda, R. Krataitong, T. Yotkaew, N. Tosangthum, A. Wiengmoon, R. Tongsri, Sintered dual-phase steels produced from pre-alloyed Fe-Cr-Mo powder. Chiang Mai J. Sci., 43 (2016) 358-364.

DOI: 10.1016/j.matdes.2015.09.030

[8] M. Enomoto and H.I. Aaronson, Nucleation kinetics of proeutectoid ferrite at austenite grain boundaries in Fe-C-X alloys, Metall. Trans A, 17A (1986) 1385-1397.

DOI: 10.1007/bf02650120

[9] Z. Zhang and R.A. Farrar, Role of non-metallic inclusions in formation of acicular ferrite in low alloy weld metals, Mater. Sci. Technol., 12 (1996) 237-260.

DOI: 10.1179/mst.1996.12.3.237

[10] M.W. Wu and K.S. Hwang, Improved homogenization of Ni in sintered steels through the use of Cr-containing prealloyed powders, Metall. Trans A, 37 (2006) 3577-3585.

DOI: 10.1007/s11661-006-1052-4

[11] A. S. Podder, I. Lonardelli, A. Morinari and H.K.D.H. Bhadeshia, Thermal stability of retained austenite in bainitic steel: an in situ study, Proc. R. Soc. A 467 (2011) 3141-3156.

DOI: 10.1098/rspa.2011.0212

[12] B.D. Cooman, Structure-properties relationship in TRIP steels containing carbide-free bainite, Curr. Opin. Solid State Mater. Sci., 8 (2004) 285-303.

DOI: 10.1016/j.cossms.2004.10.002

[13] Hoganas AB, Metallography, Handbook for sintered components, 6, Sweden, (2015).