Production from PLA Materials Processed Vertically by FDM Method RP Technology

Abstract:

The article is focused on the aspects in samples production of sophisticated material – PLA - PolyLacticAcid, PLA plastic. The main part of the work focuses on experimental production and testing of PLA material - PolyLacticAcid plastic, printed on RepRap 3D device that works on the "open source" principle. The article presents the outcomes of test materials in the form of measurement protocols recorded in the software, the measured values ​​in a static tensile test, marked down in tables and shown in work graphs. The article describes selected and carried out tests of mechanical properties of PLA plastics extruded in different directions in this case carried out vertically by FDM rapid prototyping method of two PLA materials such as pure without additives blended with blue dye. The tests are mainly focused on the determination of ultimate tensile strength. Based on the results obtained, the samples made of two PLA materials were compared in the end to establish which produced PLA material sample is stronger. There are outputs in the form of logs, charts and tables that provide information about the executed tests and comparisons, which were made by the authors.

• Periodical: Key Engineering Materials (Volume 756)
• Pages: 80-87
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.756.80
• Online since: September 2017
• Authors: Anton Panda*, Ema Nováková-Marcinčinová, Ľudmila Nováková-Marcinčinová, Tibor Krenický, Tadeusz Zaborowski
• Keywords: PLA Materials, Rapid Prototyping, RepRap 3D Device

References

[1] A. Panda, J. Jurko, I. Pandová, Monitoring and Evaluation of Production Processes. An Analysis of the Automotive Industry, Springer International Publishing, Switzerland, 2016, 117 p.

[2] L. Novakova-Marcincinova, J. Novak-Marcincin, Production of composite material by FDM rapid prototyping technology, Applied Mechanics and Materials 474 (2014) 186-191.

DOI: 10.4028/www.scientific.net/amm.474.186

[3] J. Jurko, A. Panda, M. Behún, Prediction of a new form of the cutting tool according to achieve the desired surface quality, Applied Mechanics and Materials 268 (2013) 473-476.

DOI: 10.4028/www.scientific.net/amm.268-270.473

[4] L. Novakova-Marcincinova, J. Novak-Marcincin, Production of ABS-Aramid Composite Material by Fused Deposition Modeling Rapid Prototyping System, Manufacturing Technology 14/1 (2014) 85-91.

DOI: 10.21062/ujep/x.2014/a/1213-2489/mt/14/1/85

[5] L. Novakova-Marcincinova, J. Novak-Marcincin, Rapid prototyping in developing process with CA systems application, Applied Mechanics and Materials 464 (2014) 399-405.

DOI: 10.4028/www.scientific.net/amm.464.399

[6] L. Novakova-Marcincinova, J. Novak-Marcincin, Testing of ABS Material Tensile Strength for Fused Deposition Modeling Rapid Prototyping Method, Advanced Materials Research 912-914 (2014) 370-373.

DOI: 10.4028/www.scientific.net/amr.912-914.370

[7] L. Novakova-Marcincinova, J. Novak-Marcincin, Selected Testing for Rapid Prototyping Technology Operation, Applied Mechanics and Materials 308 (2013) 25-31.

DOI: 10.4028/www.scientific.net/amm.308.25

[8] A. Panda, M. Prislupčák, I. Pandová, Progressive technology diagnostic and factors affecting to machinability, Applied Mechanics and Materials 616 (2014) 183-190.

DOI: 10.4028/www.scientific.net/amm.616.183

[9] M. Prislupčák, A. Panda, M. Jančík, I. Pandová, P. Orendáč, T. Krenický, Diagnostic and experimental valuation on progressive machining unit, Applied Mechanics and Materials 616 (2014) 191-199.

DOI: 10.4028/www.scientific.net/amm.616.191

[10] L. Novakova-Marcincinova, I. Kuric, Basic and Advanced Materials for Fused Deposition Modeling Rapid Prototyping Technology, Manuf. and Industrial Engineering 11 (2012) 24-27.

[11] M. Plancak, Rapid Prototyping and Rapid Tooling, FTN University of Novi Sad, Novi Sad, 2009, 164 p.

[12] I. Pandová, Nitrogen oxides reduction by zeolite sorbents in manufacturing use, Advanced Materials Research 937 (2014) 487-490.

DOI: 10.4028/www.scientific.net/amr.937.487

[13] I. Pandová, Manufacturing technologies in automotive production and waste water cleaning on zeolite in view of copper, MM Science Journal 2016 (2016) 1218-1221.

DOI: 10.17973/mmsj.2016_11_201648

[14] J. Peterka, P. Pokorný, Influence of the Lead Angle from the Vertical Axis Milling on Effective Radiu sof the Cutter, Key Engineering Materials 581 (2014) 44-49.

DOI: 10.4028/www.scientific.net/kem.581.44

[15] I. Leššo, P. Flegner, J. Futó, Z. Sabová, Utilization of signal spaces for improvement of efficiency of metallurgical process, Metalurgija 53 (2014) 75-77.

[16] J. Brezinová, A. Guzanová, E. Spišák, Assessment of properties thermal sprayed coatings realised using cermet blend powder, Metalurgija 53/4 (2014) 661-664.

[17] M. Gombár, A. Vagaská, J. Kmec, P. Michal, Microhardness of the Coatings Created by Anodic Oxidation of Aluminium, Applied Mechanics and Materials 308 (2013) 95-100.

DOI: 10.4028/www.scientific.net/amm.308.95

[18] K. Monková, P. Monka, D. Jakubeczyová, The research of the high speed steels produced by powder and casting metallurgy from the view of tool cutting life, Applied Mechanics and Materials 302 (2013) 269-274.

DOI: 10.4028/www.scientific.net/amm.302.269

[19] J. Janekova, J. Kovac, D. Onofrejova, Modelling of Production Lines for Mass Production of Sanitary Products, Procedia Engineering 96 (2014) 330-337.

[20] Š. Olejárová, R. Kreheľ, M. Pollák, M. Kočiško, Research on impacts of mechanical vibrations on the production machine to its rate of change of technical state, Advances in mechanical engineering 8/7 (2016) 1-10.

DOI: 10.1177/1687814016655778

[21] Ľ. Straka, I. Čorný, R. Kreheľ, Evaluation of Capability of Measuring Device on the Basis of Diagnostics, Applied Mechanics and Materials 308 (2013) 69-74.

DOI: 10.4028/www.scientific.net/amm.308.69

[22] A. Panda et al., Roller bearings and analytical expression of selected cutting tools durability in machining process of steel 80MoCrV4016, Applied Mechanics and Material 415 (2013) 610-613.

DOI: 10.4028/www.scientific.net/amm.415.610

[23] A. Panda et al., Analytical expression of T-vc dependence in standard ISO 3685 for cutting ceramic, Key Engineering Materials 480-481 (2011) 317-322.

DOI: 10.4028/www.scientific.net/kem.480-481.317

[24] A. Panda, J. Jurko, J. Valíček, M. Harničárová, I. Pandová, Study on cone roller bearing surface roughness improvement and the effect of surface roughness on tapered roller bearing service life, Int. J. of Advanced Manufacturing Technology 82/5-8 (2016).

DOI: 10.1007/s00170-015-7449-8

[25] A. Panda, J. Jurko, M. Džupon, I. Pandová, Iveta, Optimalization of heat treatment bearings rings with goal to eliminate deformation of material, Chemické listy 105/16 (2011) 459-461.

[26] P. Michalik, J. Zajac, M. Hatala, D. Mitaľ, V. Fečová, Monitoring surface roughness oft hin-walled components from steel C45 machining down and up milling, Measurement 58 (2014) 416-428.

DOI: 10.1016/j.measurement.2014.09.008

[27] T. Krenický, Implementation of Virtual Instrumentation for Machinery Monitoring, in: Scientific Papers: Operation and Diagnostics of Machines and Production Systems Operational States: Vol. 4, RAM-Verlag, Lüdenscheid, 2011, pp.5-8.

[28] T. Krenický, Non-contact Study of Surfaces Created Using the AWJ Technology, Manufacturing Technology 15/1 (2015) 61-64.

DOI: 10.21062/ujep/x.2015/a/1213-2489/mt/15/1/61

[29] I. Vojtko, V. Simkulet, P. Baron, I. Orlovský, Microstructural Characteristics Investigation of the Chip-Making Process after Machining, Applied Mechanics and Materials 616 (2014) 344-350.

DOI: 10.4028/www.scientific.net/amm.616.344

[30] E. Ragan, J. Dobránsky, P. Baron, M. Kočiško, J. Svetlík, Dynamic of taking out molding parts at injection molding, Metallurgy 51/4 (2012) 567-570.

[31] Š. Álló, V. Kročko, M. Korenko, Z. Andrássyová, D. Foldešiová, Effect of chemical degreasing on corrosion stability of components in automobile industry, Advanced Materials Research 801 (2013) 19-23.

DOI: 10.4028/www.scientific.net/amr.801.19

[32] T. Krenický, P. Jacko, Simultaneous temperature monitoring using virtualization, in: Scientific Papers: Operation and diagnostics of machines and production systems operational states. Lüdenscheid: RAM-Verlag, 2009, pp.58-62.

[33] R. Cep, A. Janásek, J. Petru et al., Surface roughness after machining and influence of feed rate on process, Key Engineering Materials 581 (2014) 341-347.

DOI: 10.4028/www.scientific.net/kem.581.341