Experimental and Analytical Assessment of the Power Parameters of the Combined Rolling-Extruding Process Using a Round Billet from Alloy 01417 Obtained Using an Electromagnetic Mold

Abstract:

Analytical and experimental studies have been carried out, which made it possible to propose new technological modes of combined rolling-extruding for the production of rods from alloy 01417 for the further drawing of wire for electrical purposes. The force parameters on the rolls and the die are calculated when extruding a rod with a diameter of 5 mm on the laboratory unit CRE-200 and the industrial unit CRE-400. The obtained values of the forces on the rolls and the die do not exceed the permissible values of the power load of the units. Therefore the selected parameters are suitable for conducting experiments on the manufacture of prototypes of rods. To verify the conclusions made, experimental studies were carried out on the CRE-200 unit at a temperature of 320 oC and a drawing coefficient μ = 12.1. The results of experimental studies in comparison with the calculated data showed that the deviation of the calculated data does not exceed 15%.

• Periodical: Key Engineering Materials (Volume 887)
• Pages: 300-305
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.887.300
• Online since: May 2021
• Authors: S. Sidelnikov, D. Voroshilov*, M. Motkov, V. Bespalov, M. Voroshilova
• Keywords: Aluminum, Combined Rolling-Extruding, Electromagnetic Mold, Force Parameters, Mechanical Properties, Rare-Earth Metals, Wire

References

[1] Yu.A. Gorbunov, The Role and Prospects of Rare Earth Metals in the Development of Physical-Mechanical Characteristics and Applications of Deformable Aluminum Alloys, Journal of Siberian Federal University. Engineering & Technologies. 8(5) (2015) 636-645.

DOI: 10.17516/1999-494x-2015-8-5-636-645

[2] D.I. Belyy, Aluminium alloys for leads of cable products, Kabeli i Provoda. 1 (2012) 8-15.

[3] D.A. Chernavina, E.A. Chernavin, A.V. Faller, M.Yu. Zdanovich, Global aluminum market: development trends, prospects and key problems, Molodoy uchenyy. 17 (2018) 206-210.

[4] V.G. Shmorgun, L.M. Gurevich, A.F. Trudov, S.P. Pisarev et al., Mechanical properties of wire with a carrier layer of aluminum alloy 01417, Izvestiya VolGTU. 136(9) (2014) 109-113.

[5] V.S. Sudavtsova, M.A. Shevchenko, V.V. Berezutskiy, M.I. Ivanov, I.V. Mateyko, V.G. Kudin, Thermodynamic properties and phase equilibria in alloys of Al (Si)–Ce binary systems, Journal of Physical Chemistry. 88(5) (2014) 736-746.

[6] A. Mogucheva, D. Zyabkin, R. Kaibyshev, Effect of the thermomechanical processing on microstructure and properties of an Al-Ce alloy, Materials Science Forum. 706-709 (2012) 361-366.

DOI: 10.4028/www.scientific.net/msf.706-709.361

[7] N.A. Belov, A.N. Alabin, A.R. Teleuova, Comparative analysis of alloying additives as applied to the production of heat-resistant aluminum-base wires, Metal Science and Heat Treatment. 53(9-10) (2012) 455-459.

DOI: 10.1007/s11041-012-9415-5

[8] S.B. Sidelnikov, N.N. Dovzhenko, T.N. Drozdova et al., Investigation of the structure and assessment of properties of cast and deformed semifinished products from alloys of the Al-REM system with different nickel content, Vestnik of Nosov Magnitogorsk State Technical University. 1 (2013) 45-48.

[9] M. Zhang, H. Wang, W. Han, M. Zhang, Yu. Li, Ya. Wang, Yu. Xue, F. Ma, X. Zhang. Electrochemical extraction of cerium and formation of Al–Ce alloy from CeO2 assisted by AlCl3 in LiCl–KCl melts, Sci China Chem. 57(11) (2014) 1477-1482.

DOI: 10.1007/s11426-014-5214-8

[10] H. Liao, Y. Wu, Y. Wang, Microstructure Evolution of Al-0.35%Si-0.2%Mg-0.3%Ce Alloy During Hot Extrusion and Its Contributions to Performances, Journal of Materials Engineering and Performance. 24(6) (2015) 2503-2510.

DOI: 10.1007/s11665-015-1485-2

[11] H. Liao, Y. Liu, C. Lü, Q. Wang, Mechanisms for Ce-induced remarkable improvement of conductivity in Al alloys, Journal of Materials Research. 32(3) (2017) 566-574.

DOI: 10.1557/jmr.2016.477

[12] Z.M. Shi, K. Gao, Y.T. Shi, Y. Wang, Microstructure and mechanical properties of rare-earth-modified Al−1Fe binary alloys, Materials Science and Engineering: A. 632 (2017) 62-71.

DOI: 10.1016/j.msea.2015.02.068

[13] TS 1-809-1038-2018. Electrotechnical wire of aluminum alloy mark 01417. Technical specifications. Publ. 13.06.(2018).

[14] S.B. Sidelnikikov, N.N. Dovzhenko, N.N. Zagirov. Combined and complex methods of machining non-ferrous metals and alloys, M.: MAKS PRESS, (2005).

[15] S.B. Sidelnikov, D.S. Voroshilov, M.V. Pervukhin, M.M. Motkov, Development and research of technology for producing electrotechnical wire from alloys of the Al – REM system, obtained with the application of combined machining methods, Tsvetnye metally. 9 (2019) 63-68.

DOI: 10.17580/tsm.2019.09.10

[16] S. Sidelnikov, D. Voroshilov, M. Motkov, M. Voroshilova, V. Bespalov, Development of Combined Machining Modes, Investigation of Mechanical Properties and Structure of Deformed Semi-Finished Products from Alloy 01417, Materials Science Forum. 992 (2020) 498-503.

DOI: 10.4028/www.scientific.net/msf.992.498