Investigations on Combined In Situ CT and Acoustic Analysis during Clinching

Abstract:

Clinching is a cost efficient method for joining components in series production. To assure the clinch point’s quality, the force displacement curve during clinching or the bottom thickness are monitored. The most significant geometrical characteristics of the clinch point, neck thickness and undercut, are usually tested destructively by microsectioning. However, micrograph preparation goes ahead with a resetting of elastic deformations and crack-closing after unloading. To generate a comprehensive knowledge of the clinch point’s inner geometry under load, in-situ computed tomography (CT) and acoustic testing (TDA) can be combined. While the TDA is highly sensitive to the inner state of the clinch point, it could detect critical events like crack development during loading. If such events are indicated, the loading process is stopped and a stepped in-situ CT of the following crack and deformation development is performed. In this paper, the concept is applied to the process of clinching itself, providing a detailed three-dimensional insight in the development of the joining zone. A test set-up is used which allows a stepwise clinching of two aluminium sheets EN AW 6014. Furthermore, this set-up is positioned within a CT system. In order to minimize X-ray absorption, a beryllium cylinder is used within the set-up frame and clinching tools are made from Si3N4. The actuator and sensor necessary for the TDA are integrated in the set-up. In regular process steps, the clinching process is interrupted in order to perform a TDA and a CT scan. In order to enhance the visibility of the interface, a thin tin layer is positioned between the sheets prior clinching. It is shown, that the test-set up allows a monitoring of the dynamic behaviour of the specimen during clinching while the CT scans visualize the inner geometry and material flow non-destructively.

• Periodical: Key Engineering Materials (Volume 926)
• Pages: 1489-1497
• DOI: https://doi.org/10.4028/p-32330d
• Online since: July 2022
• Authors: Daniel Köhler*, Richard Stephan, Robert Kupfer, Juliane Troschitz, Alexander Brosius, Maik Gude
• Keywords: Active Acoustic Testing, Clinching, Process Monitoring, X-Ray

References

[1] Deutscher Verband für Schweißen und verwandte Verfahren e. V., Mechanisches Fügen, DVS Merkblätter und Richtlinien; 10. Düsseldorf: DVS-Verlag, (2009).

DOI: 10.1002/mawe.19780090512

[2] J. Varis, Economics of clinched joint compared to riveted joint and example of applying calculations to a volume product, J. Mater. Process. Technol. 172 (2006) 130-138.

DOI: 10.1016/j.jmatprotec.2005.09.009

[3] Y. Tan, O. Hahn, and F. Du, Process monitoring method with window technique for clinch joining, ISIJ Int. 45 (2005) 723-729.

DOI: 10.2355/isijinternational.45.723

[4] L. Pejryd, T. Beno, and S. Carmignato, Computed tomography as a tool for examining surface integrity in drilled holes in CFRP composites, Procedia CIRP 13 (2014) 43-48.

DOI: 10.1016/j.procir.2014.04.008

[5] W. G. Drossel, R. Mauermann, R. Grützner, and D. Mattheß, Numerical and experimental analysis of self piercing riveting process with carbon fiber-reinforced plastic and aluminium sheets, Key Eng. Mater. 554–557 (2013) 1045-1054.

DOI: 10.4028/www.scientific.net/kem.554-557.1045

[6] R. Füßel, M. Gude, and A. Mertel, In-situ x-ray computed tomography analysis of adhesively bonded riveted lap joints, in: 17th European Conference on Composite Materials. Munich, (2016).

[7] F. Pottmeyer, J. Bittner, P. Pinter, and K. A. Weidenmann, In-Situ CT Damage Analysis of Metal Inserts Embedded in Carbon Fiber-Reinforced Plastics, Exp. Mech. 57 (2017) 1411-1422, (2017).

DOI: 10.1007/s11340-017-0312-0

[8] J. Esteban and C. A. Rogers, Energy dissipation through joints: Theory and experiments, Comput. Struct. 75 (2000) 347-359.

DOI: 10.1016/s0045-7949(99)00096-6

[9] F. Wang, L. Huo, and G. Song, A piezoelectric active sensing method for quantitative monitoring of bolt loosening using energy dissipation caused by tangential damping based on the fractal contact theory, Smart Mater. Struct. 27 (2017 0-17.

DOI: 10.1088/1361-665x/aa9a65

[10] H. Bournine, D. J. Wagg, and S. Neild, Vibration damping in bolted friction beam-columns, Proc. ASME Des. Eng. Tech. Conf. 330 (2009) 365-372, (2009).

DOI: 10.1115/detc2009-87184

[11] K. Holeczek, P. Kostka, and N. Modler, Dry friction contribution to damage-caused increase of damping in fiber-reinforced polymer-based composites, Adv. Eng. Mater. 16 (2014) 1284-1292.

DOI: 10.1002/adem.201400293

[12] Z. Zhang, M. Liu, Z. Su, and Y. Xiao, Quantitative evaluation of residual torque of a loose bolt based on wave energy dissipation and vibro-acoustic modulation: A comparative study, J. Sound Vib. 383 (2016) 156-170.

DOI: 10.1016/j.jsv.2016.07.001

[13] D. Köhler, B. Sadeghian, R. Kupfer, J. Troschitz, M. Gude, and A. Brosius, A Method for Characterization of Geometric Deviations in Clinch Points with Computed Tomography and Transient Dynamic Analysis, Key Eng. Mater. 883 (2021) 89-96.

DOI: 10.4028/www.scientific.net/kem.883.89

[14] D. Köhler, R. Kupfer, and M. Gude, Clinching in in-situ CT—A numerical study on suitable tool materials, J. Adv. Join. Process. 2. (2020).

DOI: 10.25518/esaform21.2781

[15] D. Köhler, R. Kupfer, J. Troschitz, and M. Gude, Clinching in In-situ CT – Experimental Study on Suitable Tool Materials, in: ESAFORM 2021, 24th International Conference on Material Forming, Liège, 2021, p.1–11.

DOI: 10.25518/esaform21.2781

[16] R. Bhattacharya, M. Stanton, I. Dargue, G. Williams, and R. Aylmore, Forming limit studies on different thickness aluminium 6XXX series alloys used in automotive applications, Int. J. Mater. Form. 3 (2010) 267-270.

DOI: 10.1007/s12289-010-0758-4