Selective Laser Melting of Ti6Al4V: Effects of Heat Accumulation Phenomena due to Building Orientation

Abstract:

Titanium alloy Ti6Al4V is one of the most utilized alloys in the field of additive manufacturing due to the excellent combination of mechanical properties, density and good corrosion behavior. These characteristics make the use of this material particularly attractive for additively manufacturing components with complex geometry in sectors such as aeronautics and biomedical. Selective Laser Melting (SLM), by which a component is fabricated by selectively melting of stacked layers of powder using a laser beam, is the one of most promising additive manufacturing technologies for Ti6Al4V alloy. Although this technique offers numerous advantages, it has some critical issues related to the high thermal gradients, associated with the process, promoting the formation of a metastable martensitic microstructure resulting in high tensile strength but poor ductility of the produced parts. The formation of microstructural defects such as balling and porosity can occur together with the presence of residual stresses that may significantly affect the mechanical characteristics of the component. Specific process parameters and geometries can determine heat accumulation phenomena that result in a progressive decrease in thermal gradients between layers. These heat accumulation phenomena are influenced by the number of layers deposited, but also by the building orientation that, for a given geometry, determines a variation of the deposited surface for each layer.

• Periodical: Key Engineering Materials (Volume 926)
• Pages: 226-234
• DOI: https://doi.org/10.4028/p-42a3kf
• Online since: July 2022
• Authors: Dina Palmeri*, Gianluca Buffa, Gaetano Pollara, Livan Fratini
• Keywords: Building Orientation, Heat Accumulation, Selective Laser Melting (SLM), Ti6Al4V

References

[1] Shunyu Liu,Yung C. Shin, Additive manufacturing of Ti6Al4V alloy: A review, Materials & Design Volume 164 (2019) 107552.

DOI: 10.1016/j.matdes.2018.107552

[2] H. Shipley et. al, Optimisation of process parameters to address fundamental challenges during selective laser melting of Ti-6Al-4V: A review, Int. J. Mach. Tools Manuf., V. 128 (2018) 1-20.

DOI: 10.1016/j.ijmachtools.2018.01.003

[3] D. Barba, C. Alabort, Y.T. Tang, M.J. Viscasillas, R.C. Reed, E. Alabort, On the size and orientation effect in additive manufactured Ti-6Al-4V, Mater. Des. 186 (2020). 108235.

DOI: 10.1016/j.matdes.2019.108235

[4] S. Ren, Y. Chen, T. Liu, X. Qu, Effect of Build Orientation on Mechanical Properties and Microstructure of Ti-6Al-4V Manufactured by Selective Laser Melting, Metall. Mater. Trans. A Phys. Metall. Mater. Sci. 50 (2019) 4388–4409.

DOI: 10.1007/s11661-019-05322-w

[5] M. Simonelli, Y.Y. Tse, C. Tuck, Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti-6Al-4V, Mater. Sci. Eng. A. 616 (2014) 1–11.

DOI: 10.1016/j.msea.2014.07.086

[6] Z.W. Xu, A. Liu, X.S. Wang, The influence of building direction on the fatigue crack propagation behavior of Ti6Al4V alloy produced by selective laser melting, Mater. Sci. Eng. A. 767 (2019).

DOI: 10.1016/j.msea.2019.138409

[7] W. Sun, Y. Ma, W. Huang, W. Zhang, X. Qian, Effects of build direction on tensile and fatigue performance of selective laser melting Ti6Al4V titanium alloy, Int. J. Fatigue. 130 (2020).

DOI: 10.1016/j.ijfatigue.2019.105260

[8] P. Hartunian, M. Eshraghi, Effect of Build Orientation on the Microstructure and Mechanical Properties of Selective Laser-Melted Ti-6Al-4V Alloy, J. Manuf. Mater. Process. 2 (2018) 69.

DOI: 10.3390/jmmp2040069

[9] Z. Xie, Y. Dai, X. Ou, S. Ni, M. Song, Effects of selective laser melting build orientations on the microstructure and tensile performance of Ti–6Al–4V alloy, Mater. Sci. Eng. A. 776 (2020) 139001.

DOI: 10.1016/j.msea.2020.139001

[10] D. Palmeri, G. Buffa, G. Pollara, L. Fratini, Sample building orientation effect on porosity and mechanical properties in Selective Laser Melting of Ti6Al4V titanium alloy, Mater. Sci. Eng. A., 830 (2022) 142306.

DOI: 10.1016/j.msea.2021.142306

[11] D. Palmeri, G. Buffa, G. Pollara, L. Fratini, The Effect of Building Direction on Microstructure and Microhardness during Selective Laser Melting of Ti6Al4V Titanium Alloy. J. of Materi Eng and Perform 30, 8725–8734 (2021).

DOI: 10.1007/s11665-021-06039-x

[12] Y. Li, D. Gu, Thermal behavior during selective laser melting of commercially pure titanium powder: Numerical simulation and experimental study, Addit. Manuf. 1 (2014) 99–109.

DOI: 10.1016/j.addma.2014.09.001

[13] C. Phutela, N.T. Aboulkhair, C.J. Tuck, I. Ashcroft, The effects of feature sizes in selectively laser melted Ti-6Al-4V parts on the validity of optimised process parameters, Materials (Basel). 13 (2020) 117.

DOI: 10.3390/ma13010117