Characterization of Natural Rubber (NR), Polybutadiene Rubber (BR) and Styrene-Butadiene Rubber (SBR) Blends Cured in a Vulcanization System

Abstract:

In this work, the mechanical properties of three types of dough rubber NR, NR/BR, and NR/SBR have been investigated using five percentages of materials fill (30, 40, 50, 60, and 70) pphr. Carbon black was used as a filler material. The tensile test was achieved with 300% elongation and strain rates of (100, 200, 300, 400, and 500) mm/min. The tensile strength results indicate that the maximum value of tensile strength for NR Dough carbon black 60 pphr reaches 23.2 MPa; the maximum tensile strain of NR dough (carbon black 50 pphr) reaches 805.5%, and the modulus of elasticity with carbon black 70 pphr reaches 4.3 MPa. It was found that the compression strength decreases with increasing the carbon black, and the maximum value of compression set at NR dough (carbon black 30 pphr) reaches 29.3%. Fatigue crack growth was achieved according to ASTM D 813 for rubber testing. The minimum value of fatigue strength dough (carbon black 70 pphr) reaches 68 (IRHD). For NR dough (carbon black 30,40,50 pphr) reaches 3.5 mm at the number of cycles 15000 cycle. Finally, the maximum hardness of NR.

• Periodical: Materials Science Forum (Volume 1039)
• Pages: 51-64
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.1039.51
• Online since: July 2021
• Authors: Muhsin Jaber Jweeg*, Zaid G.A. Al-Jlaihawi
• Keywords: Blends, Natural Rubber, Polybutadiene, Styrene-Butadiene

References

[1] L R G and Treloar, The physics of Rubber Elasticity, 3rd Edition, Clarendon Press, Oxford (1975).

[2] L Bokobza and J P Chauvin, Reinforcement of the Natural Rubber: use of in Situ Generated Silicas and Nanofibers of Sepiolite, Elsevier Ltd. Polymer, 46 (2005) 4144–4151.

DOI: 10.1016/j.polymer.2005.02.048

[3] M J Wang, Rubber Chem. Technology, Polymer Testing, 71 (1999) 520.

[4] M J Jweeg, K K Resan and M Tariq, Study of Creep-Fatigue Interaction In A Prosthetic Socket Below Knee, ASME 2012, International Mechanical Engineering, Houston, Texas, USA (2012).

DOI: 10.1115/imece2012-85240

[5] M Hack, D Carrela-Payan, B Magneville, T Naito, Y Urushiyama, and T Yamazaki, A progressive Damage Fatigue Model for Unidirectional Laminated Composites in Finite Element Analysis: Theory and Practice, Proceeding of the 7th Eng. Integrity society, International Conference on durability and Fatigue, Downing College, Cambridge, U.K., 3–5 (2017).

DOI: 10.3221/igf-esis.46.06

[6] Z Lu, B Feng, and CLoh, The Fatigue Crack Growth Characteristics of Addition-Manufactured Alloys for Fatigue Behavior and Mean Stress Effect of Thermoplastic Polymers and Composites, Proceeding of the 7th Eng. Integrity society, International Conference on durability and Fatigue, Downing College, Cambridge, U.K., 3–5 (2017).

[7] M J Jweeg, M Al-Waily, D C Howard and HY Ahmad, Fatigue Limits of Natural Rubber Using Carbon Black Filler Materials (Proceeding of the 7th Eng. Integrity society, International Conference on durability and Fatigue, Downing College, Cambridge, U.K., 3-5 (2017).

[8] Muhannad Al-Waily, Alaa Abdulzahra Deli, Aziz Darweesh Al-Mawash and Zaman Abud Almalik Abud Ali, Effect of Natural Sisal Fiber Reinforcement on the Composite Plate Buckling Behavior, International Journal of Mechanical & Mechatronics Engineering, 17, 1 (2017).

[9] Mohsin Abdullah Al-Shammari and Sahar Emad Abdullah, Stiffness to Weight Ratio of Various Mechanical and Thermal Loaded Hyper Composite Plate Structures, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012051

[10] Jumaa S Chiad, Muhannad Al-Waily and Mohsin Abdullah Al-Shammari, Buckling Investigation of Isotropic Composite Plate Reinforced by Different Types of Powders, International Journal of Mechanical Engineering and Technology, 9, 9 (2018) 305–317.

[11] Yousuf Jamal Mahboba and Mohsin Abdullah Al-Shammari, Enhancing wear rate of high-density polyethylene (HDPE) by adding ceramic particles to propose an option for artificial hip joint liner, IOP Conference Series: Materials Science and Engineering 561 (2019).

DOI: 10.1088/1757-899x/561/1/012071

[12] Mahmud Rasheed Ismail, Zaman Abud Almalik Abud Ali and Muhannad Al-Waily, Delamination Damage Effect on Buckling Behavior of Woven Reinforcement Composite Materials Plate, International Journal of Mechanical & Mechatronics Engineering, 18, 5 (2018) 83–93.

[13] Muhsin J Jweeg, Muhannad Al-Waily, Ahmed K Muhammad and Kadhim K Resan, Effects of Temperature on the Characterisation of a New Design for a Non-Articulated Prosthetic Foot, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012064

[14] Fahad M Kadhim, Ayad M Takhakh and Asmaa M Abdullah, Mechanical Properties of Polymer with Different Reinforcement Material Composite That used for Fabricates Prosthetic Socket, Journal of Mechanical Engineering Research and Developments, 42, 4 (2019) 118–123.

DOI: 10.26480/jmerd.04.2019.118.123

[15] Mohsin Abdullah Al-Shammari, Emad Q Hussein and Ameer Alaa Oleiwi, Material Characterization and Stress Analysis of a Through Knee Prosthesis Sockets, International Journal of Mechanical & Mechatronics Engineering, 17, 6 (2017).

[16] Ekhlas Edan Kader, Akram Mahdi Abed and Mohsin Abdullah Al-Shammari, Al2O3 Reinforcement Effect on Structural Properties of Epoxy Polysulfide Copolymer, Journal of Mechanical Engineering Research and Developments, 43, 4 (2020) 320–328.

[17] Ameer A Kadhim, Muhannad Al-Waily, Zaman Abud Almalik Abud Ali, Muhsin J Jweeg and Kadhim K Resan, Improvement Fatigue Life and Strength of Isotropic Hyper Composite Materials by Reinforcement with Different Powder Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 2 (2018).

[18] Ahmed Khaleel Abdulameer and Mohsin Abdullah Al-Shammari, Fatigue Analysis of Syme's Prosthesis, International Review of Mechanical Engineering, 12, 3 (2018).

[19] Worood Hussein and Mohsin Abdullah Al-Shammari, Fatigue and Fracture Behaviours of FSW and FSP Joints of AA5083-H111 Aluminium Alloy, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012055

[20] Kadhim K Resan, Abbas A Alasadi, Muhannad Al-Waily and Muhsin J Jweeg, Influence of Temperature on Fatigue Life for Friction Stir Welding of Aluminum Alloy Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 2 (2018).

[21] Saif M Abbas, Kadhim K Resan, Ahmed K Muhammad and Muhannad Al-Waily, Mechanical and Fatigue Behaviors of Prosthetic for Partial Foot Amputation with Various Composite Materials Types Effect, International Journal of Mechanical Engineering and Technology, 9, 9 (2018) 383–394.

[22] Mohsin Abdullah Al-Shammari, Qasim H Bader, Muhannad Al-Waily and A M Hasson, Fatigue Behavior of Steel Beam Coated with Nanoparticles under High Temperature, Journal of Mechanical Engineering Research and Developments, 43, 4 (2020) 287–298.

[23] Ehab N. Abbas, Muhsin J. Jweeg and Muhannad Al-Waily, Fatigue Characterization of Laminated Composites used in Prosthetic Sockets Manufacturing, Journal of Mechanical Engineering Research and Developments, 43, 5 (2020) 384-399.

[24] Marwah Mohammed Abdulridha, Nasreen Dakel Fahad and Muhannad Al-Waily, Kadhim K Resan, Rubber Creep Behavior Investigation with Multi Wall Tube Carbon Nano Particle Material Effect, International Journal of Mechanical Engineering and Technology, 9, 12 (2018) 729–746.

[25] Sadiq emad Sadiq, Sadeq Hussein Bakhy and Muhsin Jaber Jweeg, Effects of Spot Welding Parameters on the Shear Characteristics of Aluminum Honeycomb Core Sandwich Panels in Aircraft structure, Test Engineering and Management, 83 (2020) 7244 –7255.

DOI: 10.1088/1757-899x/928/2/022126

[26] H J Abbas, M J Jweeg, Muhannad Al-Waily and Abbas Ali Diwan, Experimental Testing and Theoretical Prediction of Fiber Optical Cable for Fault Detection and Identification, Journal of Engineering and Applied Sciences, 14, 2 (2019) 430–438.

DOI: 10.36478/jeasci.2019.430.438

[27] Muhannad Al-Waily, Emad Q Hussein and Nibras A Aziz Al-Roubaiee, Numerical Modeling for Mechanical Characteristics Study of Different Materials Artificial Hip Joint with Inclination and Gait Cycle Angle Effect, Journal of Mechanical Engineering Research & Developments, 42, 4 (2019) 79–93.

DOI: 10.26480/jmerd.04.2019.79.93

[28] Esraa A. Abbod, Muhannad Al-Waily, Ziadoon M. R. Al-Hadrayi, Kadhim K. Resan and Saif M. Abbas, Numerical and Experimental Analysis to Predict Life of Removable Partial Denture, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Engineering and Advanced Technology, 870 (2020).

DOI: 10.1088/1757-899x/870/1/012149

[29] Sihama I Salih, Jawad K Oleiwi and Hajir Mohammed Ali, Investigation the Properties of Silicone Rubber Blend Reinforced by Natural Nanoparticles and UHMWPE fiber, International Journal of Mechanical Engineering and Technology, 10, 1 (2019).

[30] Muhsin J Jweeg, Ali S Hammood and Muhannad Al-Waily, A Suggested Analytical Solution of Isotropic Composite Plate with Crack Effect, International Journal of Mechanical & Mechatronics Engineering, 12, 5 (2012).

[31] Ehab N Abbas, Muhsin J Jweeg and Muhannad Al-Waily, Analytical and Numerical Investigations for Dynamic Response of Composite Plates Under Various Dynamic Loading with the Influence of Carbon Multi-Wall Tube Nano Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 6 (2018).

[32] Muhannad Al-Waily and Zaman Abud Almalik Abud Ali, A Suggested Analytical Solution of Powder Reinforcement Effect on Buckling Load for Isotropic Mat and Short Hyper Composite Materials Plate, International Journal of Mechanical & Mechatronics Engineering, 15, 4 (2015).

[33] Mohsin Abdullah Al-Shammari and Muhannad Al-Waily, Analytical Investigation of Buckling Behavior of Honeycombs Sandwich Combined Plate Structure, International Journal of Mechanical and Production Engineering Research and Development, 8, 4 (2018) 771–786.

DOI: 10.24247/ijmperdaug201883

[34] Muhannad Al-Waily, Mohsin Abdullah Al-Shammari and Muhsin J. Jweeg, An Analytical Investigation of Thermal Buckling Behavior of Composite Plates Reinforced by Carbon Nano Particles, Engineering Journal, 24, 3 (2020).

DOI: 10.4186/ej.2020.24.3.11

[35] A Ciesielski, An Introduction to Rubber Technology, Published Rapra Technology Limited, ch 3 (1999) 31–32.

[36] G Kraus, Reinforcement of Elastomers, Interscience, New York (1965).

[37] A N Gent, Engineering with Rubber: How to Design Rubber Components, Hanser publishers, ch 2 (1992) 19–21.

[38] Muhannad Al-Waily, Iman Q. Al Saffar, Suhair G. Hussein and Mohsin Abdullah Al-Shammari, Life Enhancement of Partial Removable Denture made by Biomaterials Reinforced by Graphene Nanoplates and Hydroxyapatite with the Aid of Artificial Neural Network, Journal of Mechanical Engineering Research and Developments, 43, 6 (2020) 269-285.

[39] Ehab N Abbas, Muhannad Al-Waily, Tariq M Hammza and Muhsin J Jweeg, An Investigation to the Effects of Impact Strength on Laminated Notched Composites used in Prosthetic Sockets Manufacturing, IOP Conference Series: Materials Science and Engineering, 2nd International Scientific Conference of Al-Ayen University, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022081

[40] Sadiq Emad Sadiq, Muhsin J Jweeg and Sadeq H Bakhy, The Effects of Honeycomb Parameters on Transient Response of an Aircraft Sandwich Panel Structure, IOP Conference Series: Materials Science and Engineering, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022126

[41] Muhannad Al-Waily, Moneer H Tolephih and Muhsin J Jweeg, Fatigue Characterization for Composite Materials used in Artificial Socket Prostheses with the Adding of Nanoparticles, IOP Conference Series: Materials Science and Engineering, 2nd International Scientific Conference of Al-Ayen University, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022107

[42] S E Sadiq, S H Bakhy and M J Jweeg, Crashworthiness Behavior of Aircraft Sandwich Structure with Honeycomb Core under Bending Load, IOP Conference Series: Materials Science and Engineering (2020).

DOI: 10.1088/1757-899x/881/1/012046

[43] Muhsin J. Jweeg, Ali S. Hammood and Muhannad Al-Waily, Experimental and Theoretical Studies of Mechanical Properties for Reinforcement Fiber Types of Composite Materials, International Journal of Mechanical & Mechatronics Engineering, 12, 4 (2012).

[44] Mohsin Abdullah Al-Shammari, Muhannad Al-Waily, Theoretical and Numerical Vibration Investigation Study of Orthotropic Hyper Composite Plate Structure, International Journal of Mechanical & Mechatronics Engineering, 14, 6 (2014).

[45] Muhsin J. Jweeg, Muhannad Al-Waily and Alaa Abdulzahra Deli, Theoretical and Numerical Investigation of Buckling of Orthotropic Hyper Composite Plates, International Journal of Mechanical & Mechatronics Engineering, 15, 4 (2015).

[46] Muhannad Al-Waily, Maher A R Sadiq Al-Baghdadi and Rasha Hayder Al-Khayat, Flow Velocity and Crack Angle Effect on Vibration and Flow Characterization for Pipe Induce Vibration, International Journal of Mechanical & Mechatronics Engineering, 17, 5 (2017).

[47] Muhannad Al-Waily, Kadhim K. Resan, Ali Hammoudi Al-Wazir and Zaman Abud Almalik Abud Ali, Influences of Glass and Carbon Powder Reinforcement on the Vibration Response and Characterization of an Isotropic Hyper Composite Materials Plate Structure, International Journal of Mechanical & Mechatronics Engineering, 17, 6 (2017).

[48] Mahmud Rasheed Ismail, Muhannad Al-Waily and Ameer A Kadhim, Biomechanical Analysis and Gait Assessment for Normal and Braced Legs, International Journal of Mechanical & Mechatronics Engineering, 18, 3 (2018).

[49] Rasha Hayder Al-Khayat, Maher A R Sadiq Al-Baghdadi, Ragad Aziz Neama and Muhannad Al-Waily, Optimization CFD Study of Erosion in 3D Elbow During Transportation of Crude Oil Contaminated with Sand Particles, International Journal of Engineering & Technology, 7, 3 (2018).

DOI: 10.14419/ijet.v7i3.14180

[50] Saif M Abbas, Ayad M Takhakh, Mohsin Abdullah Al-Shammari and Muhannad Al-Waily, Manufacturing and Analysis of Ankle Disarticulation Prosthetic Socket (SYMES), International Journal of Mechanical Engineering and Technology, 9, 7 (2018) 560–569.

[51] Ragad Aziz Neama, Maher A R Sadiq Al-Baghdadi and Muhannad Al-Waily, Effect of Blank Holder Force and Punch Number on the Forming Behavior of Conventional Dies, International Journal of Mechanical & Mechatronics Engineering, 18, 4 (2018).

[52] Muhsin J Jweeg, Kadhim K Resan, Esraa A Abbod and Muhannad Al-Waily, Dissimilar Aluminium Alloys Welding by Friction Stir Processing and Reverse Rotation Friction Stir Processing, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012059

[53] Suhair Ghazi Hussein, Mohsin Abdullah Al-Shammari, Ayad M Takhakh and Muhannad Al-Waily, Effect of Heat Treatment on Mechanical and Vibration Properties for 6061 and 2024 Aluminum Alloys, Journal of Mechanical Engineering Research and Developments, 43, 1 (2020).

[54] Sadeq H. Bakhy and Muhannad Al-Waily, Development and Modeling of a Soft Finger in Robotics Based on Force Distribution, Journal of Mechanical Engineering Research and Developments, 44, 1 (2021) 382-395.

[55] Tammam Salim Naji Aswad, Mohd Azahari Bin Razali and Muhannad Al-Waily, Numerical Study of the Shape Obstacle Effect on Improving the Efficiency of Photovoltaic Cell, Journal of Mechanical Engineering Research and Developments, 44, 2 (2021) 209-224.

[56] Muhsin J. Jweeg, H. A. Hamzah, Muhannad Al-Waily, Mohsin Abdullah Al-Shammari, A Finite Element Simulation of Nano Effects on Stress Distribution in a Below Knee Prosthetic, 4th International Conference on Engineering Sciences, IOP Conference Series: Materials Science and Engineering, 1067 (2021).

DOI: 10.1088/1757-899x/1067/1/012141

[57] Hayder Zaher Abdalikhwa, Mohsin Abdullah Al-Shammari, Emad Qasem Hussein, Characterization and Buckling Investigation of Composite Materials to be used in the Prosthetic Pylon Manufacturing, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012170

[58] Mohammed Hussein Kadhim Aljaberi, Maher AR Sadiq Al-Baghdadi, Muhannad Al-Waily, M Mohammadi-Aghdam, Taha Goudarzi, Numerical Investigation of Mechanical Behavior for Lattice Structure with Effect of Different Nanomaterial Types, IOP Conference Series: Materials Science and Engineering, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012172

[59] Emad Kadum Njim, Muhannad Al-Waily, Sadeq H Bakhy, A Critical Review of Recent Research of Free Vibration and Stability of Functionally Graded Materials of Sandwich Plate, IOP Conference Series: Materials Science and Engineering, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012081

[60] Rasha M Hussien and Mohsin Abdullah Al-Shammari, Optimization of Friction Stir Welded Aluminium Plates by the New Modified Particle Swarm Optimization, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012156

[61] Emad Kadum Njim, Muhannad Al-Waily, Sadeq H. Bakhy, A Review of the Recent Research on the Experimental Tests of Functionally Graded Sandwich Panels, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 420-441.

DOI: 10.1016/j.matpr.2021.03.235

[62] Zaman Abud Almalik Abud Ali, Ameer A. Kadhim, Rasha Hayder Al-Khayat, Muhannad Al-Waily, Review Influence of Loads upon Delamination Buckling in Composite Structures, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 392-406.

[63] Ameer A. Kadhim, Esraa A. Abbod, Ahmed K. Muhammad, Kadhim K. Resan, Muhannad Al-Waily, Manufacturing and Analyzing of a New Prosthetic Shank with Adapters by 3D Printer, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 383-391.

[64] Saddam K Al-Raheem, Muhsin J Jweeg, Abdul kareem F Hassan, Design and Construction of Device for Rubber Material Fatigue Test, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012173

[65] Mohammed S Jabbar , Muhsin J Jweeg and Adnan I Mohammed, Numerical and Experimental Study of Elastic Recovery in Deep Drawing of Low Carbon and Galvanized Steel Sheet Conical Products, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012155