Monitoring Precipitation Kinetics in Heat Treatable Aluminium Alloys Using In Situ Resistivity in Gleeble Thermomechanical Simulator

Nicolas Chobaut; Denis Carron; Jean Marie Drezet

doi:10.4028/www.scientific.net/MSF.794-796.921

Paper Titles

Effects of Isothermal Aging on Clustering and Paint-Bake Hardening Behavior in an Al-Mg-Si Alloy
p.897

Influence of Pre-Straining and Pre-Ageing on the Age-Hardening Response of Al-Mg-Si Alloys
p.903

Use of Multicomponent Phase Diagrams for Designing High Strength Casting Aluminum Alloys
p.909

Quantitative Phase Analysis of Al-Mg-Li and Al-Cu-Li Alloys
p.915

Monitoring Precipitation Kinetics in Heat Treatable Aluminium Alloys Using In Situ Resistivity in Gleeble Thermomechanical Simulator
p.921

Complementarity of Atom Probe, Small Angle Scattering and Differential Scanning Calorimetry for the Study of Precipitation in Aluminium Alloys
p.926

Early-Stage Precipitation Phenomena and Composition-Dependent Hardening in Al-Mg-Si-(Cu) Alloys
p.933

In Situ Isothermal Calorimetric Measurement of Precipitation Behaviour in Al-Mg-Si Alloys
p.939

The Influence of Mg and Ag on the Precipitation Kinetics and the Formation of the T₁ Phase in Al-Cu-Li Alloys
p.945

HomeMaterials Science ForumMaterials Science Forum Vols. 794-796Monitoring Precipitation Kinetics in Heat...

Monitoring Precipitation Kinetics in Heat Treatable Aluminium Alloys Using In Situ Resistivity in Gleeble Thermomechanical Simulator

Abstract:

A conventional way to determine precipitation kinetics in heat treatable aluminium alloys is to monitor the associated solute loss by in-situ resistivity. A Gleeble machine is used to perform so called isothermal quenching (IQ) resistivity measurements. IQ consists in quenching the alloy down to a given temperature and holding it at this temperature. The results are validated against measurements performed with a classical four-points method using continuous current on the same alloy.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volumes 794-796)

Pages:

921-925

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.794-796.921

Citation:

Cite this paper

Online since:

June 2014

Authors:

Nicolas Chobaut*, Denis Carron, Jean Marie Drezet

Keywords:

Aluminium Alloy, Gleeble Machine, Precipitation, Resistivity

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] M. Perez, O. Lame and A. Deschamps, Global techniques for characterizing phase transformations: a tutorial review, Adv. eng. Mat., 12 (2010) 433-446.

DOI: 10.1002/adem.201000039

Google Scholar

[2] S. I. Vooijs, S. B. Davenport and I. Todd, Monitoring the precipitation reactions in a cold-rolled Al–Mn–Mg–Cu alloy using thermoelectric power and electrical resistivity measurements, Philosophical Magazine A, 81, 8 (2001) 2059-(2072).

DOI: 10.1080/01418610010028954

Google Scholar

[3] M. Dehmas, P. Weisbecker, G. Geandier, P. Archambault and E. Aeby-Gautier, Experimental study of phase transformations in 3003 aluminium alloys during heating by in situ high energy X-ray synchrotron radiation, Journal of Alloys and Compounds, 400 (2005).

DOI: 10.1016/j.jallcom.2005.03.062

Google Scholar

[4] P. Archambault and D. Godard, High temperature precipitation kinetics and TTT curve of a 7xxx alloy by in-situ electrical resistivity measurements and differential calorimetry, Scripta Materialia, 42 (2000) 675-680.

DOI: 10.1016/s1359-6462(99)00419-4

Google Scholar

[5] R.H. Brown and L.A. Willey, Aluminium Vol I: Properties, Physical Metallurgy, and Phase. Diagrams, K.R. Van Horn, ed., ASM, Metals Park, OH, (1967).

Google Scholar

[6] C. Samuel and S. Viswanathan, Specimen configurations for Gleeble dilatometry of steels, Materials Science & Technology, ASM, Materials Park, OH (2008) 1872-1883.

Google Scholar

[7] D. Godard, E. Gautier, P. Archambault and C. Sigli, The modelling of the heterogeneous precipitation in Al-Zn-Mg-Cu alloys during quenching, Proceedings of the International Conference on Solid-Solid Phase Transformations, edited by M. Koiwa, K. Otsuka and T. Miyazaki, The Japan Institute of Metals (1999).

Google Scholar