For Libraries For Publication Open Access Downloads About Us Contact Us
Paper Titles
Research on the Preparation of HA/PEEK Gradient Composites by Impregnation Method and the Biosecurity
p.35
A Novel Synthesis of Solid-Solid (SSMePCM) by In Situ Polymerization
p.43
Investigation of a Microwave Absorbing Material Based on NBR
p.49
Application of Chitosan as Scaffold Material of Construction In Vitro
p.53
Experimental Study on the Tool Wear in Milling Carbon Fiber Reinforced Plastics
p.57
Preparation and Blood Coagulation Property of Ortho Hydroxytoluene Chitosan
p.62
Research on Crystallinity, Morphology of Cotton Subjected to Enzyme and Crosslinking Treatment
p.71
Use Discolor Spectrophotometry to Characterize Chelate Property of Nanoparticle
p.77
Effect of Calcination Heating Rate on Microstructure and Performances of NSR Catalyst
p.81

Experimental Study on the Tool Wear in Milling Carbon Fiber Reinforced Plastics

Article Preview

Abstract:

Basing on the milling experiment of carbon fiber reinforced plastics (CFRP), the wear performance of CVD diamond coated tool with different cutting edge is compared and studied. The result shows that lifetimes of interlaced edge and herringbone edge milling cutters are significantly higher than general edge milling cutter, under the same parameters. The lifetime of interlaced edge milling cutter is about 2 times than herringbone edge milling cutter, and 3.5 times than general edge milling cutter. The wear failure mechanisms of CVD diamond coated tools are abrasive wear and coating peeling, which are caused by micro-cutting of hard carbon fiber and the impact action of mechanical load and thermal stress.

You might also be interested in these eBooks
Mechanical Engineering, Materials Science and Civil Engineering IV View Preview

Info:

Periodical:

Materials Science Forum (Volume 893)

Pages:

57-61

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.893.57

Citation:

Cite this paper

Online since:

March 2017

Authors:

Ju Dong Liu*, Xiao Fan Yang, Zhi Long Xu, You Sheng Li, Guo Hong Yan, Li Kun Huang

Keywords:

CFRP, CVD Diamond Coated Tool, Machinability, Wear Mechanism

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2017 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

References

[1] O. S. David-West, D. H. Nash and W. M. Banks: Compos. Struct. Vol. 83(2008), pp.247-258.

Google Scholar

[2] X. H. Zhang, Y. Meng, W. Zhang: Fiber Compos. 1(2004), pp.50-53 (In Chinese).

Google Scholar

[3] R. Selzer and K. Friedrich: J. Mater. Sci. Vol. 30(2) (1995), pp.334-338.

Google Scholar

[4] R. Selzer and K. Friedrich: Compos. Vol. 28A(1997), pp.595-604.

Google Scholar

[5] A. Koplev, A. Lystrup and T. Vorm: Compos. Vol. 14(4) (1983), pp.371-376.

Google Scholar

[6] W. C. Chen: Int. J. Mach. Tools  Manuf. Vol. 37(8) (1997), pp.1097-1108.

Google Scholar

[7] K. Weinert and C. Kempmann: Adv. Eng. Mater. Vol. 6(8) (2004), pp.684-689.

Google Scholar

[8] H. J. Zhang, W. Y. Chen and D. C. Chen: Chin. J. Mech. Eng. Vol. 40(12)(2004) , pp.145-149 (In Chinese).

Google Scholar

[9] C. C. Tsao: Inter, J. Adv. Manuf. Technol. Vol. 37(2008), pp.23-28.

Google Scholar

[10] H. H. Xu, Q. Xu and D. Liu: Mach. Design Manuf. ChinaVol. 12(2009), pp.167-169 (In Chinese).

Google Scholar

© 2025 Trans Tech Publications Ltd. All rights are reserved, including those for text and data mining, AI training, and similar technologies. For open access content, terms of the Creative Commons licensing CC-BY are applied.
Scientific.Net is a registered trademark of Trans Tech Publications Ltd.