The Measurement of Residual Stresses in the Surface Layers of the Materials after Machining

Marian Králik; Vladimír Jerz

doi:10.4028/www.scientific.net/MSF.919.345

Paper Titles

Industry 4.0, Logistics 4.0 and Materials - Chances and Solutions
p.307

The Numerical Analysis of Axially Loaded Elastomeric Bushing
p.315

The Size of the Friction Coefficient of the Sliding Pair Depending on the Lubricant Used
p.327

Impact of Applied Anti-Reflective Material on Accuracy of Optical 3D Digitisation
p.335

The Measurement of Residual Stresses in the Surface Layers of the Materials after Machining
p.345

Analysis of Hardfacing and Milling of Forging Die by CAx Technologies
p.354

The Effect of Materials on the Efficiency of the Spiroid Gearing
p.362

Method of Evaluation of the Properties of Thin Steel Sheets by Springback Test
p.370

Optical and Electron Microscopy Investigation of Damaged Storz Firehose Couplings Microstructure
p.379

HomeMaterials Science ForumMaterials Science Forum Vol. 919The Measurement of Residual Stresses in the...

The Measurement of Residual Stresses in the Surface Layers of the Materials after Machining

Abstract:

This paper deals with the problem of stresses in the surface layer of materials after machining. It analyzes residual stresses as one of the factors affecting the state of the surface layer after machining. It describes the methods for measuring residual stresses and evaluates them from the point of view of suitability for industrial practice. A new method of measuring residual stresses in the surface layer of a workpiece for laboratory use has been proposed and experimentally tested. At the end of the article the options for further solutions in this area are proposed.

You might also be interested in these eBooks

Novel Trends in Production Devices and Systems IV

View Preview

Info:

Periodical:

Materials Science Forum (Volume 919)

Pages:

345-353

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.919.345

Citation:

Cite this paper

Online since:

April 2018

Authors:

Marian Králik, Vladimír Jerz*

Keywords:

Elastic-Plastic Deformation, Lifetime, Machining, Residual Stresses, Surface Layer

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] M. Kráčalík, Stav povrchových vrstiev po obrábaní s dôrazom na povrchové napätia, Diplomová práca, Bratislava: SjF STU, (2012).

Google Scholar

[2] B. Bumbálek, L. Bumbálek, Zbytková napětí a jejich význam při řešení integrity povrchu. In Strojírenská technologie, roč. 11, č. 3, 2006, ISSN 1211-4162, s. 9-16.

Google Scholar

[3] M. Klesnil, P. Lukáš, Únava kovových materiálů při mechanickém namáhání, Praha: Academia, 1975, 224 s.

Google Scholar

[4] J. Dušek, Tvrdost, mikrotvrdost, nanotvrdost – čisté kovy měřené metodou DSI, Disertační práce. Brno: Masarykova univerzita v Brně, Přírodovědecká fakulta, 2008. 171 s.

Google Scholar

[5] Přehled vlastností oceli S355J0 [online]. [cit. 2011-12-30]. http: /prirucka. bolzano. cz/cz/technicka-podpora/techprirI/tycovaocel/EN10025/S355JO/>.

Google Scholar