Development of Technology of Robotized Laser Welding of Thin Wall Products from Heat-Resistant Alloys

Abstract:

Results of the developed industrial technology of restoration of a surface corrosion-resistant staly are presented by method of laser building up. The comparative analysis of a microstructure of the built-up wearproof layer, an alloyage zone with material of a basis and diffusive zone at the different technological modes of building up is given. Influence of morphology of particles of additive powder on parametrical characteristics of the roller received by laser gas powder building up is investigated. The optimum modes of building up on a substrate from steel 12Cr18Ni10Ti are set. Tests for firmness against intercrystalline corrosion of the built-up powder compositions are executed by the AM method. Metalgraphic assessment of corrosion resistance is presented.

• Periodical: Materials Science Forum (Volume 992)
• Pages: 663-669
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.992.663
• Online since: May 2020
• Authors: Svetlana E. Krylova*, V.A. Zavyalov, M.I. Goltapin
• Keywords: Carbide Hardening of a Blanket, Corrosion-Resistant Became, Laser Building Up, Multicomponent Powder Compositions, Transitional Diffusive Layer, Wear Resistance

References

[1] А.I. Noskov, R.M. Yanbayev, T.M. Shakhsrakhmanov, The influence of density composition of additive powder and the parameters of laser coaxial build-up on rollers formation, Metallurgical science and metal thermal treatment, №7 (745) 2017, pp.70-73.

[2] A.G. Gigoryants, I.N. Shiganov, A.I. Misyurov, Laser treatment technological processes, М.: MSTU n.a. Bauman N.E. publishing, 2008, 664 p.

[3] A.G. Grigoryants, A.N. Safonov, V.V. Shibaev, Powder metallurgy, №9, 1984, p.39.

[4] A.G. Grigoryants, A.I. Misyurov, R.S. Tretyakov, Analysis of the effect of coaxial laser deposition parameters on the formation of rollers, Machinal-engineering technology, №11, 2011, pp.19-21.

[5] C.Y. Kong, P.A. Carroll, P. Brown, R.J. Scudamore, The effect of average powder particle size on deposition efficiency, deposit height and surface roughness in the direct metal laser deposition process, Paper presented at 14th International Conference on Joining of Material, 29 April 2007 – 2 May 2017, Helsingor, Denmark.

[6] S.E. Krylova, The influence of technological parameters of laser build-up on the structural characteristics of the restored surface layer, Ural school of young metal scientists: source book reports of XVII international scientific-technological Ural school of metal scientists, katerinburg, 2016, pp.50-54.

[7] S.E. Krylova, S.P. Oplesnin, A.S. Yasakov, A.O. Strizhov, The technology of laser build-up by powder materials under conditions of protection gas of pump and compressor equipment items, Laser technological complexes and technologies for industrial materials processing, Bulletin LAS №25, (2017).

[8] T.V. Tarasova, A.V. Gusarov, K.E. Protasov, The influence of thermal fields on the structure of corrosion resistant steel by different laser treatment schemes, Metal science and thermal treatment of metals №7 (745), 2017, pp.37-44.

DOI: 10.1007/s11041-017-0168-z

[9] S.E. Krylova, S.P. Oplesnin, A.O. Strizhov, The influence of technological parameters of gas powder laser build-up on structural characteristics of rebuilt surface layer of corrosion resistant steel, Metal science and thermal treatment of metals №10 (748), 2017, pp.35-40.

DOI: 10.1007/s11041-018-0204-7

[10] V.A. Zavyalov, S.E. Krylova, S.P. Oplesnin, I.A. Kurnoskin, Actual problems of physical metal science of XXIV Ural school of metal scientists and heat treaters, FSBEI of Higher Education «Magnitogorsk State Technical University n.a. G.I. Nosov», 2018, pp.55-57.