Paper Titles

Welding of Aluminium Alloy Thin Sheets Using Variable Polarity MIG Method
p.15

Effect of Ti Addition to Zn Filler Metal on Wettability and Reinforcement of Soldered Joint of Aluminum
p.23

CMT Robotized Welding of Thin-Walled Joints Made of 7xxx Series Aluminium Alloy
p.31

Effect of Electrode Negative Ratio in AC MIG Welding of Aluminium Alloy 6082 on the Microstructure and Properties of Heat Affected Zone
p.39

Hybrid Comopsites Shaped by Casting Methods
p.47

Fine Particle Reinforced Composites Obtained by Suspension Method
p.53

Assessment of the Deformation of Composites with Aluminum Matrix Designed for the Metal Forming
p.57

The Microstructure of Elektron21 and WE43 Magnesium Casting Alloys after Subsequent Melting Process Operations
p.65

The Quality of Produced Sand-Cast Engine Block Made from Elektron 21 Magnesium Alloy
p.71

HomeSolid State PhenomenaSolid State Phenomena Vol. 211Hybrid Comopsites Shaped by Casting Methods

Hybrid Comopsites Shaped by Casting Methods

Article Preview

Abstract:

In the presented work two methods of casting: gravity casting and centrifugal casting have been described. The main aim of the study was development procedures for producing the AlSi / SiC+C hybrid composite. Composite suspensions with the same phase composition were cast into molds with different coefficients of thermal conductivity. This allowed to determine the influence of thermal conditions on the formation of the structure and distribution of particles in the matrix. In the paper the conditions of casting, macro-and microstructure and selected properties of the casts have been presented. The structure of components and cast composites was examined by light and electron microscope, applying properly made preparations.

You might also be interested in these eBooks

Light Metal and their Alloys III

Info:

Periodical:

Solid State Phenomena (Volume 211)

Pages:

47-52

DOI:

https://doi.org/10.4028/www.scientific.net/SSP.211.47

Citation:

Cite this paper

Online since:

November 2013

Authors:

Anna J. Dolata*

Keywords:

Cast Aluminum Alloy, Casting Methods, Hybrid Composite, Structure

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2014 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

[1] R. Saha, E. Morris, N. Chawla, Hybrid and conventional particle reinforced metal matrix composites by squeeze infiltration casting, J. Mater. Sci. Lett. 21 (2002) 337– 339.

[2] A. Dolata-Grosz, B. Formanek, J. Śleziona, J. Wieczorek, Al-FeAl-TiAl-Al2O3 composite with hybrid reinforcement, Journal of Mat. Proc. Techn. 162-163 (2005) 33-38.

DOI: 10.1016/j.jmatprotec.2005.02.009

[3] D. Satishkumar, M. Kanthababu, R. Saravanan, T. Moorthy, P. Saravanan, G. Srinivasan, Optimization of WEDM parameters on machining of A17075 based hybrid MMCs, Adv. Comp. Letters 21/4 (2012) 100-106.

DOI: 10.1177/096369351202100403

[4] A. J. Dolata, M. Dyzia, Aspects of fabrication aluminium matrix heterophase composites by suspension method, IOP Conference Series: Materials Science and Engineering 35/1 (2012) 012020.

DOI: 10.1088/1757-899x/35/1/012020

[5] J. Wieczorek, J. Śleziona, A. Dolata-Grosz, J. Myalski, Influence of material of friction partner on tribological properties of heterophase composites, Kompozyty (Composites) 8/1 (2008) 5-10.

[6] K. Naplocha, K. Granat, Dry sliding wear of Al/Saffil/C hybrid metal matrix composites, Wear 265 (2008) 1734-1740.

DOI: 10.1016/j.wear.2008.04.006

[7] S. Suresha, B.K. Sridhara, Friction characteristics of aluminium silicon carbide graphite hybrid composites, Materials & Design 34 (2012) 576–583.

DOI: 10.1016/j.matdes.2011.05.010

[8] A.J. Dolata, M. Dyzia, W. Walke, Influence of Particles Type and Shape on the Corrosion Resistance of Aluminium Hybrid Composites, Solid St. Phen. 191 (2012) 81-87.

DOI: 10.4028/www.scientific.net/ssp.191.81

[9] K. K. Alanemea, P. A. Olubambi, Corrosion and wear behaviour of rice husk ash—Alumina reinforced Al–Mg–Si alloy matrix hybrid composites, Journal of Mat. Research and Techn. 2/2 (2013) 188–194.

DOI: 10.1016/j.jmrt.2013.02.005

[10] A. Posmyk, H. Wistuba, Composite layers with ceramic matrix modified with glassy carbon destined for oil-less sliding pairings, Arch. of Metall. and Materials 56 (2011) 909-917.

DOI: 10.2478/v10172-011-0100-2

[11] A. Dolata-Grosz, W. Hufenbach, J. Śleziona, M. Gude, A. Czulak, Design, manufacture and technological verification of SiC/C composite stirrer, Arch. of Materials Science and Engineering 39/1 (2009) 1 29-37.

[12] M. Dyzia, AlSi7Mg/SiC and Heterophase SiCp+Cg Composite for Use in Cylinder-Piston System of Air Compressor, Solid St. Phen. 176 (2011) 49-54.

DOI: 10.4028/www.scientific.net/ssp.176.49

[13] A. Dolata-Grosz, Interaction of Al-Si alloys with SiC/C ceramic particles and their influence on microstructure of composites, Solid St. Phen. 176 (2011) 55-62.

DOI: 10.4028/www.scientific.net/ssp.176.55

[14] K. Landry, S. Kalogeropoulou, N. Eustathopoulos, Wettability of carbon by aluminum and aluminum alloys, Materials Science and Engineering A 254 (1998) 99-111.

DOI: 10.1016/s0921-5093(98)00759-x

[15] A. Dolata-Grosz, M. Dyzia, J. Śleziona, The formation of the structure of cast composites in different solidification conditions, Arch. of Materials Science and Engineering 31/1 (2008) 13-16.

[16] K. Gawdzińska, J. Szala, M. Maliński, Computer programs to model three dimensional structure of the MMC, Arch. of Foundry Engineering 9/4 (2009) 53-56.