Effect of Serpentine Channel Pouring Process on the Microstructure of Semi-Solid 6061 Aluminum Alloy Slurry

Abstract:

The semi-solid slurry of 6061 aluminum alloy was prepared by the serpentine channel pouring process. The influence of graphite serpentine channel and copper serpentine channel on the slurry was comparative analyzed. The effect of pouring temperature on the slurry microstructure was also investigated. The results indicate that both copper and graphite serpentine channel can be used to prepare semi-solid slurry with spherical primary grains. Compared with a permanent casting, the microstructure of the semi-solid slurry was significantly improved and refined. With the increase of pouring temperature, the average equivalent grain diameter of the primary phase grains in the semi-solid slurry increases gradually, but the shape factor decreases gradually. When the pouring temperature increased from 675 °C to 690 °C, a high quality semi-solid slurry can be obtained. Comparing the two kinds of serpentine channel, it is found that the copper serpentine channel can make the primary grains finer, and the average equivalent grain size was 63 μm. However, the solidified shell near the inner graphite serpentine channel surface was thinner than that of the copper serpentine channel. In conclusion, the graphite serpentine channel is more suitable for preparing semi-solid 6061 aluminum alloy slurry.

• Periodical: Solid State Phenomena (Volume 327)
• Pages: 255-262
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.327.255
• Online since: January 2022
• Authors: Nai Yong Li*, Wei Min Mao, Xiao Xin Geng, Peng Yu Yan
• Keywords: 6061 Aluminum Alloy, Microstructure, Semi-Solid Slurry, Serpentine Channel Pouring Process

References

[1] J.F. Jiang, G.F. Xiao, Y. Wang, Y.Z. Liu, Y. Zhang, High temperature deformation behavior and microstructure evolution of wrought nickel-based superalloy GH4037 in solid and semi-solid states, Transactions of Nonferrous Metals Society of China, 30(3) 2020 710-726.

DOI: 10.1016/s1003-6326(20)65248-7

[2] L.L. Fan, M.Y. Zhou, Y.W.X. Zhang, Q. Tang, G.F. Quan, B. Liu, The semi-solid microstructural evolution and coarsening kinetics of AZ80-0.2Y-0.15Ca magnesium alloy, Materials Characterization, 154 2019 116-126.

DOI: 10.1016/j.matchar.2019.05.019

[3] Y.F. Wang, S.D. Zhao, X.Z. Zhao, Y.Q. Zhao, Effects of isothermal treatment parameters on the microstructure of semisolid alloys, Materials Science and Technology, 34(1) 2018 104-110.

DOI: 10.1080/02670836.2017.1364329

[4] B. Zhou, S. Lu, K.L. Xu, C. Xu, Z.Y. Wang, B.J. Wang, Hot cracking tendency test and simulation of 7075 semi-solid aluminium alloy, Transactions of Nonferrous Metals Society of China, 30(2) 2020 318-332.

DOI: 10.1016/s1003-6326(20)65215-3

[5] S.Z. Shang, G.M. Lu, X.L. Tang, Z.X. Zhao, C.M. Wu, Deformation mechanism and forming properties of 6061Al alloys during compression in semi-solid state, Transactions of Nonferrous Metals Society of China, 20(9) 2010 1725-1730.

DOI: 10.1016/s1003-6326(09)60365-4

[6] N. Wang, Z.M. Zhou, G.M. Lu, Microstructural Evolution of 6061 Alloy during Isothermal Heat Treatment, Journal of Materials Science & Technology, 27(1) 2011 8-14.

DOI: 10.1016/s1005-0302(11)60018-2

[7] Z.J. Yang, K.K. Wang, Y. Yang, Optimization of ECAP-RAP process for preparing semisolid billet of 6061 aluminum alloy, International Journal of Minerals Metallurgy and Materials, 27(6) 2020 792-800.

DOI: 10.1007/s12613-019-1895-5

[8] Z.Z. Chen, W.M. Mao, Z.C. Wu, Influence of serpentine channel pouring process parameters on semi-solid A356 aluminum alloy slurry, Transactions of Nonferrous Metals Society of China, 21(5) 2011 985-990.

DOI: 10.1016/s1003-6326(11)60810-8

[9] Z.Y. Liu, W.M. Mao, W.P. Wang, Z.K. Zheng, Preparation of semi-solid A380 aluminum alloy slurry by serpentine channel, Transactions of Nonferrous Metals Society of China, 25(5) 2015 1419-1426.

DOI: 10.1016/s1003-6326(15)63741-4

[10] J.F. Jiang, Y. Wang, G.F. Xiao, X. Nie, Comparison of microstructural evolution of 7075 aluminum alloy fabricated by SIMA and RAP, Journal of Materials Processing Technology, 238 2016 361-372.

DOI: 10.1016/j.jmatprotec.2016.06.020