Search Options

Sort by:

Sort search results by

Publication Type:

Publication Type filter

Open access:

Publication Date:

Periodicals:

Periodicals filter

Search results

Online since: June 2014
Authors: Khalid El Bikri, Benamar Rhali, A. Abdenbi Boukhzer
EL BIKRI Khalid2,b and C.
Qian et al. [7] further presented the plane strain static thermostatic deformations of a rectangular simply supported FG elastic plate using the same methodologies.
EL Bikri, R.
EL Kadiri, R.
EL Kadiri, R.
Online since: June 2011
Authors: Qiu Xiang Liu, Jun Bo Wu, Yan Ping Jiang, Xin Gui Tang
El-Harrad et al. confirmed that there are two ranges of the Ba concentration, x < 0.1 and x > 0.1 and the best dielectric properties occurs in ceramics with x = 0.1 [14], but Rujijanagul and Bongkarn have observed a different results [11].
El-Harrad, P.
Online since: March 2017
Authors: Suzi Salwah Jikan, Nur Azam Badarulzaman, Rozainita Rosley
Abd El Meguid, S.
Abd El Rehim, E.
Al Gruenwald, J.
Online since: March 2012
Authors: Zhen Hong Jia, Hong Yan Zhang, Xiao Yi Lv
El-Bahar, Y.
El-Bahar, Y.
Al-Mariri, Sensors and Actuators B Vol.160 (2011), p.835
Online since: October 2006
Authors: Edwige Bano, Nicolas Camara, Konstantinos Zekentes, Aurelie Thuaire, Alexander A. Lebedev
a) b) Fig. 6: EL of the pin diode (a), in forward mode at 2.9V, 10mA (without structural defect) and (b), reverse mode at 450V, 1mA a) b) c) d) Fig. 7: Forward EL of the pin diode exhibiting structural features (a), for all wavelengths (b), at 450nm (c), at 600nm and (d) at 700nm.
Gunjishima et al.: NATURE ,Vol. 430 (2004), p. 1009 [2] E.
Online since: October 2016
Authors: B. Sivaraman, P. Jothiprakash, Senthil Padmavathy, T. Keerthivasan
Sivakumar et al [1] machined AISI D3 steel using Taguchi L18 OA in WEDM.
Shanmuga prakash et al [5] reviewed the machining of tool and die steel in WEDM.
El-Taweel et al [3] investigated the effects of machining parameters of wire electric discharge machining of inconel 601 using responsive surface methodology.
Kanlayasiri et al [6] investigated the wedm machining parameters for better surface finish in DC53 die steel effectively.
Ko-Ta Chiang et al [7], done an analysis on SG cast iron getting better surface roughness using RSM while machining in EDM.
Online since: November 2012
Authors: Hong Tao Li, Xiu Hong Xu, Jia Liu
If used properly, it can not only curtail the environmental issue but also aid agricultural production as a natural fertilizer (El-Din et al., 2000; Hoitink et al., 1986).
Microbial additives of compost have been studied extensively (Kim et al., 2004; Nakai et al., 2004; Sasaki et al., 2006; Wakase et al., 2008), but few studies have been conducted to track the microbial additives throughout the entire process of composting.
DNA extractions and purification DNA was extracted according to protocols described previously (Zhou, et al., 1996; Zhang, et al., 2003), with the following modifications.
The dominant microorganisms in the natural compost of Pseudomonas sp. et al. became less or disappeared after added MA (band 10, 11, 12, 13) .
Technol. 100, 5444–5453 [3] El-Din, S.M.S.B., Attia, M., Abo-Sedera, S.A., 2000.
Online since: January 2018
Authors: Edson Jansen Pedrosa Miranda Jr., J.M.C. dos Santos
Al2O3 3970 10844 6421.4 46.685 16.370 Epoxy 1142 2654.5 1175.6 0.805 0.158 *The parameters listened in Table 1 were obtained and calculated using the physical parameters from Yao et al. [13].
El-Kady: Measurement Science and Technology Vol. 20 (2009), p. 012002
El-Naggar, S.I.
Online since: March 2013
Authors: Yue Chen
The total mass of the model is 22.0t, among them, the model mass and the attached mass account for 19.0t and the mass of the base plate is 3.0t, respectively (Chen, Lu et al., 2008).
Fig.7 shows the comparison between time history of these seismic wave and the response spectrum of the Shanghai Code(Lu, Chen et al., 2012).
(a)Time history and (b) response spectrum comparison between El Centro and Code of Shanghai Test Results’ Analysis Strain Behavior of Model Structure.
[2] Chen Y, Lu XL, Lu WS et al , Test Design of a Shaking Table Model for a Super Tall-building with High Level Transfer Story[C].
[4] Lu XL, Chen Y, Lu WS et al , Shaking Table Model Test on a Super Tall-building with High Level Transfer Story[C].
Online since: March 2013
Authors: Jun Xiu Shi, Jian Hua Liu
Surkov, et al.
El-Dahshan, A.M.S.
El Din, H.H.
“Galvanic corrosion in the systems titanium/316L stainless steel/Al brass in Arabian Gulf water.”
Showing 1781 to 1790 of 9913 items