Search results

Fig.1 shows the photocurrents at different X-ray flux for radiation dosimeters based on diamond films prepared by different deposition procedures.
It can also be observed from Fig.1 that the slope of the curves for the samples is different.
Table 1 lists the relative content of surface carbon combined states of diamond films with different plasma post-treatments through the XPS analysis.
References [1] M.
A Vol. 479 (2002), pp. 661

The experimental device of ice disk polishing is shown in Fig.1.
The disk needs be pre-neatened before experiment and metal material should be pre-cooled because of its quick heat conduction [1].
During Journal Title and Volume Number (to be inserted by the publisher) 479 sliding friction, the surface rough peaks collide with each other at high speed.
References [1] W.N.
Liu: 4th International Symposium on Experiment and Measurement (Shanghai, China, June 1-3, 2001).

There were many works have been carried out in the recent years in the dynamic behavior of composites pipes and plates [1-6].
The volume fraction is found to be 0.6.The material properties were determined by using universal testing machine and tabulated in Table 1.
REFERENCES [1].
NA, Design Study of Multilayered Composite Spherical Pressure Vessels, Journal of Reinforced Plastic and Composites, VII,(1992). 479-493 [15].
Sayman, O, Analysis of Multi-Layered Composite Cylinders under Hygrothermal Loading, Composites Part A, 1-11. . (2005)

., intermediate density, thermal diffusivity) [1,2].
Fig. 1: (a) shape and dimensions for mould (b) sand mould and (c) permanent mould.
References [1] A.
Enginnering and Aplied Sciences, 5(1) (2010) 32-36
Alloys and Compounds. 463 (2008) 475-479

., and reduce downtime attributable to tool replacement [1,2].
Fig. 1 A basic cryogenic treatment cycle This paper begins with a brief review of the cryogenic treatment process and presents some results of extensive research work reported by other researchers.
The cooling trend is similar to that of the basic cycle in Fig. 1 and the experimentally reported cycle in literature [15].
References [1] M.
A (479) (2008), p. 229–235 [14] K.

The effect of edge detection make full impact on higher level feature extraction,characteristics description,target identification and image understanding[1].
Experimental results and analysis The detection results using the sobel operator, the canny operator and the algorithm proposed in the paper are shown in Figure 1,Figure 2,and Figure 3.As showed in Figure 1, the density of noise is 0.01, the type of noise is salt & pepper, the format of image is JPEG.As showed in Figure 2, the density of noise is 0.03, the type of noise is salt & pepper, the format of image is JPEG.As showed in Figure 3, the density of noise is 0.03, the type of noise is gauss, the format of image is PNG.
(d) (a) (a) (b) (c) Fig.1 Comparison of different edge detection algorithm for noise image(density=0.01) (a) —noise image；(b) —detect result of sobel operator； (c) —detect result of canny operator；(d) —detect result of algorithm proposed in the paper.
References [1] Rafael C.
Beijing：Publishing House of Electronics Industry, 2003：474-479 [2] Yang J, Li X B.

Figure 1 Figure 2 Figure 3 The welding process is electric.
The welding cycle is split in four different phases, defined as following: 1.
References [1] VAN STEENBERGHE D., MOLLY L., JACOBS R., VANDEKERCKHOVE B., QUIRYNEN M., NAERT I.
J Oral Implantol 2005;31(1):18-24
Doctor OS Mag 2003;14(5):479-84

Gruber [1].
Overview Figure 1.
References [1] Gruber, T.
Machine Learning, 34(1-3), pp. 43-69, 1999
Computational linguistics, 18(4), 467-479 (1992) [7] Bengio, Y., Schwenk, H., Senécal, J.

Thus refrigeration system should regulate its capacity to match the building loads [1].
Figure 1.
The frequency of the compressor and the opening amount of the expansion valve are control parameters in order to drive the water outlet temperature and the degree of superheat respectively to desired values (Fig.1).
The Internal Running Parameters Thermal load Compressor Condenser Evaporator Inlet Outlet Inlet Outlet Inlet Outlet （%） P(KPa) T(°C ) P(KPa) T(°C) P(KPa) T(°C) P(KPa) T(°C) P(KPa) T(°C) P(KPa) T(°C) 100 358 12.6 1440 92.6 1446 90.8 1421 34.6 496 6.5 375 11.2 70 418 12.5 1316 77.4 1326 76.0 1310 31.0 479 5.2 419 10.1 TABLE III.
HVAC&R Research 2008;14(1), pp. 3–32

Table 1.
XRD patterns of the FeCo/Cu core shell nanostructured samples are shown in Fig. 1(a-d).
Fig. 1.
References [1] R.S.
Mater. 393 (2015) 479–483