Search results

The second stage is activation with steam at a high temperature to enlarge the pore structure and to increase the internal surface area.
Their morphology, internal structure, elemental decomposition, porosity and electrochemical properties of the ACs were investigated.
It is hardly to observe porous structure on the surface of C500.
Several parameters of ACs have an influence on supercapacitor performance such as surface area, pore size, pore distribution, surface chemistry and intrinsic electronic conductivity.
The porous structures were entirely formed on the surface.

The AHL sample was studied by the transmission electron microscopy (TEM) for a more detailed investigation of the structure.
SEM images show the formation of a layered structure in the sample (Fig. 2).
The peaks D (≈1355 cm–1) are associated with disordered and defective graphite structure [8].
Sonicated sample AHL-D loses it porous structure and its specific capacity become comparable to HL one (Fig. 7).
Ziatdinov, Nanographite Films: Structure and Properties, Solid St.

The immobilization process shown no effect on the membrane structure and it was stable to be used as a support in immobilization process.
Enzymatic hydrolysis performance of the mixed cellulase-amylase immobilized on the polymeric structure was determined.
The asymmetric porous structure, finger-like structure and tear-shaped elongated macrovoids which close to surface layer represented the significant influence of additives PVP.
The results have shown that, immobilized enzymes on the structure achieved its maximum activities at 50°C.
Wedekind: Chemistry Vol.200 (1999) [7] R.

The mass crystal nucleus appearance promoted the short range structure increase, and the long range structure would be destroyed almost, and thus the real contact surface was increasing and further improved the h.e. catalytic activity of electrodes.
That means the amorphous short-range order structure and long-range order structure can give a better structure of hydrogen absorption and desorption.
This was due to the amorphous content combined with nanocrystal structure, lager contact surface and binding energy of Ni-Mo structure.
J: Electroanalytical Chemistry, Vol. 448 (1998) No.1, pp. 87-93
J: Molecular Structure: Theochem, Vol.862 (2008) No.1-3, pp. 80-84

At a cathode oxygen becomes an ion (O2 reduction) and goes through an electrolyte crystalline structure to an anode side where it’s liberated.
The LSM powder was prepared by pyrolysis of nitrates (Institute of Chemistry of Solids, Ekaterinburg).
Tape casting and radial magnetic pulsed compaction (RMPC) were used to fabricate LSM-YSZ-LSM tubular structure.
To form a triple layer tubular structure the tapes were wrapped around a rod in certain consequence.
SEM examination of PL microstructure showed that PL of 7 μm in thick has a solid structure and be adhered well to Crofer (Fig. 6).

The crystalline phase in the films was identified to be the delafossite structure by X-ray diffraction.
In this delafossite structure, each Cu1+ ion linearly coordinated between two oxygen atoms, forming O-Cu-O dumbbells parallel to the c Axis.
This anisotropic geometrical arrangement of the structure should lead up to anisotropic transport and optical properties.
Until now, the optical measurements indicate that the delafossite structure composition CuAlO2 has indirect band gaps [13, 14].
It can be observed that the crystal structure of Ni-doped CuAlO2 samples is rhombohedral, along with diffraction peaks of the substrates of sapphire.

Powder distribution of the powders obtained at these experiments was determined with laser particle measurement device located at chemistry laboratory of Gazi University Engineering Faculty.
When figure 2 is examined, it can be seen that the dentritic powder structures varied as acicular, globular and tabular, which is similar to the findings in the literature.
At powder removal times of 30 and 490 minutes, a structure mostly dominated by globular dendrites was observable.
Pavlovic, M.G., Pavlovic, LJ.J., Ivanovic, E.R., Radmilovic, V., Popov, K.L., “The Effect of Particle Structure on Apparent density of Electrolitic Copper Powder”, J.

Optically Active Films Fabricated from Poly(allylamine hydrochloride) and R-(+)-1-phenylethylamine Derivatives of Poly(ethylene-alt-maleic acid) with Different Degrees of Substitution Hongyan Wang1, Kunlun Xu1, Yanqi Liu2, Xiuming Jiang1, a, Guoqiang Xiang1, Lijun He1 1School of Chemistry & Chemical Engineering, Henan University of Technology, Zhengzhou 450001, PR China 2School of Food & Biological Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002, PR China ajxm1965@haut.edu.cn Keywords: optical activity, polyelectrolyte multilayer, layer-by-layer, circular dichroism Abstract.
The structure of PEMA-PEA is shown in Fig. 1.
Chemical structure of the optically active polyelectrolyte PEMA-PEA.
The chemical structure of PEMA-PEA (Fig. 1) displays that the charge density of PEMA-PEA decrease with the increase in DS.

Additionally, application of DME can also reduce the dependence on foreign oil and secure the national energy structure.
For polymers, their oil-resistance depends strongly on the properties of the polar functional groups in their molecular structures.
Since DME has no polar head in its molecular structure and is called as a moderate polar fuel, polymers with different polarity were prepared for testing in this study, shown as chloroprene Rubber(CR), acrylate rubber(ACM), fluorosilicone rubber(FMQ), ethylene propylene-diene monomer rubber(EPDM), Nitrile Rubber(NBR) and fluoro rubber(FKM).
ACS Fuel Chemistry Division Preprints, 46(2), 400-401(2001)

Introduction Magnesium is the lightest metal structure materials in engineering, not only because of tis good electrical conductivity, thermal conductivity, damping resistance, dimensional stability and electromagnetic shielding properties, but also because of its good casting and machining performance, leading to be widely used in the automotive, electronics and aviation [1].
The alloy property is determined by its internal structure.
It shows that PU / EP is 20% for good micro-network structure and good mechanical properties.
Beijing: Chemistry industry publisher (2004) [2] Li Ying, Yu Gang, Liu Yuelong etc.