Search results

Fig. 1 Drawing of the supporting-foot plastic part The product is consisted of a large square, some small cylinder and a cone.
In the range of each factor, 4 levels are uniformly selected, as shown in table 1[1].
Warpage values at endpoints of the crack along Z axis obtained from the experiments are shown in table 2[1].
References [1] Ko-Ta Chiang, Fu-ping Chang, Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology.
Int J Adv Manuf Technol 35(2007) 468–479

The Antenna Design 1.  
As shown in Figure 1 a, air-gap L-shaped feeding arc slot antenna structure is equivalent to taking air as the medium substrate of a microstrip patch antenna. 
The air-gap L-shaped feeding arc slot antenna structure shows in figure 1 b.
References [1] Rong Fengmei, Gong Shuxi, He Xiulian.
Journal of Xi’an Electronic University,2006(33):479-481

The corresponding parameters are shown in Table 1.
The parameters of model under the case 1. 15 8 5 3 0.10 120 0 Figure 1.
The following equitation can be derived while the parameters of Tab.1 are introduced
References [1] Jashankarya M.S: Supplier Diversification Effect of Discrete Demand.
IIE Transactions, Vol.39 (2007), p.465~479.

However, the recrystal at high temperature annealing facilitated an increase of sheet resistance instaneously. 1.
The reduction reagent was prepared including CoSO4 4.59g, C2H2(NH2)2 1.296ml and 2-[2-(Bis(carboxymethyl)amino)ethyl-(carboxymethyl) amino] acetic acid, EDTA, 3.51 g.
Figure 1 shows the binding energy of the surface of Ti/Si.
References [1] H.
Elwenspoek, Thin Solid Films, Vol.479 (2005), p.89 [4] J.H.

It is therefore redevelopment of moisture masonry and protection of buildings against water and moisture integral part of the construction[4]. 2 MOISTURE OF BUILDING STRUCTURES According to Standard ČSN P 73 0610 [5] moisture of masonry is classified by Table 1.
For common practice the classification according to Table 1 is sufficient, but from viewpoint of applicability of grouting methods it is not enough.
ACKNOWLEDGEMENT The contribution was made on the basis of results of the grant project Vega Nr. 1/0472/11 named “Correlation relations between the properties of autoclaved aerated concrete and its use in the process of quality management in construction”.
REFERENCES [1] Scheffler M., Colombo P.: Cellular ceramics.
Volume 216, March 2011, 479-484 p., [3] Drochytka R., Výborný J., Košatka P., Pume D.: Pórobetón.

Dynamic Analysis of Trebling-pivot Vehicle on Undulate Pavement CAO Yuan-wen1,a, YI yan-li2,b and QIN min3,c 1.
And the full vehicle model was shown in Figure 1.
Tab.1 Main technical parameters of trebling-pivot vehicle Full vehicle LWH Boxcar LWH Wheel base front / rear tread Axle load Maximum/minim speed mm mm mm mm kg km﹒h-1 8850/2500/3200 5750/2300/1200 4500/1300 1940/1860 7000/18000 85/2 Fig.1 Full-vehicle model Pavement Model The dynamic analysis of vehicle model moving on undulate pavement was studied.
References [1] Xuejun DENG, LU SUN.
[5] Xuejun DENG.Study on System Dynamics of Vehicles and Pavement Structure [J].Journal of Southeast University，2002，32 (3):474-479

Introduction Amides play a pivotal role in pharmaceutical industry and materials chemistry [1].
Scheme 1.
Table 1.
References [1] A.
Bode Rethinking amide bond synthesis, Nature 480 (2011) 471–479 [3] E.

Solid-Phase Synthesis of Carbon Nanoparticles and their Application to Direct Methanol Fuel Cell Jingmei Shen 1, Guiqin Lv1, Ning Zhang2 , Shengsheng Zhang2 , Xiaohong Kang2, Hong Zhu2∗ 1.
In a typical synthesis, an aqueous reaction mixture with an H2O/cobalt salt/nickel salt/resorcinol/formaldehyde=100:0.4:0.4:1:2 was prepared by mixing the constituent material was cured at 85℃ for 3h in a closed system.
For the oxidation of amorphous carbon, the carbon sample was stirred in a solution mixture with a molar ratio of H2O/H2SO4/KMnO4=1:0.01:0.003 at 90℃for 2h .
The specific surface area of the material is 479.8m 2 /g, much larger than carbon Vulcan-XC72 carbon.
Reference [1] S, Iijima, Nature 1991, 354,56-58 [2] C.A.

There are following unresolved questions facing before the modern researchers working in the field of electron beam lithography: 1.
The resulting structures (Figure 1) have sharp edges, fewer defects than in conventional lithography, high repeatability of elements in the arrays.
Fig. 1.
Acknowledgements Authors acknowledge the support of the Russian Ministry of Education and Science under government contracts 14.A18.21.1277, 2.8649.2013, Council of Russian President Grants under project MK-479.2013.2, the Scientific Fund of FEFU and the Russian Foundation for Basic Research under project 12-02-31328-mol-a.
References [1] M.E.

Introduction Metabonomics is defined as the quantitative measurement of the dynamic multi parametric metabolic responses of living systems to pathophysiological stimuli or genetic modification[1] .Metabonomics is the branch of science concerned with the quantitative understandings of the metabolite complement of integrated living systems and dynamic responses to the changes of both endogenous factors(such as physiology and development) and exogenous factors (such as environmental factors and xenobiotics) [2].
All data was performanced on principal component analysis(PCA), the sample score values were obtained, as shown in Figure 1, and the drug dose-effect curves was drawn by PCA mean scores, as shown in Figure 2.
Figure 1 .
References [1] J.K.
Journal of Proteome Research, 2007, 6 (2), 469-479