Search results

It is expected that large particles remaining may induce local large grains in the products after HIP.
Acknowledgements This work was supported by JSPS KAKENHI Grant Number 16H02443 and NIFS Budget Code NIFS16KOBF035.

By degree of impact strength-modifying additives may range in number LiNO₃∙3H₂O > KNO₃ > NH₄NO₃ > NaNO₃.
Methods for determination of ultimate shearing strength parallel to grain

Graphite growth results in a reduction in the concentration of carbon in the alloy so that eventually it will remain spherical graphite between the austenite grains which will be transformed into pearlite.
Increasing the number of pearlite phase means an increase of cementite phase in the material.

Despite a large number of fundamental efforts were dedicated to the DRX behaviors of the Mg alloys, few works were conducted to apply the DRX models into the FE analysis of the practical extrusion process.
The grain size is fine.

It was obvious that the appropriate addition of ZrO2 could enhance the BET surface area of Co/Al2O3 catalysts, possible because ZrO2 prevented Al2O3 to generate the large grains.
It could be seen that the olefin/paraffin ratios decreased with the increase of carbon number, indicating that the content of olefins decreased and the content of paraffins increased.

Fig.1 Grain size distribution of the silt / (mm) accumulation percentage / % Fig.2 The disposal of pore water pressure sensors Table 1 Physical properties of the silt density (g/cm3) water content ( %) void ratio liquid limit (%) compressibility coefficient (kPa-1) cohesion (kPa) internal friction angle (°) permeability coefficient (m/s) 1.99 26.4 0.733 27.3 1.4×10-4 8 34 3.5×10-7 The method of mud sedimentation under gravity is used in the model tests, which mixes the silt with water and makes the mixed mud fluid stand for 1 month in the tank.
Table 2 Model bucket foundation and the testing data of suction penetration model bucket number model bucket material diameter height wall thickness initial depth penetration rate final depth (cm) (cm) (cm) (cm) (cm/s) (cm) 2 plexiglass 15 15 0.5 3.7 0.08 3.0 3 plexiglass 15 22.5 0.5 4.0 0.07 4.2 5 steel 15 15 0.1 3.1 0.10 1.3 6 steel 15 15 0.1 2.5 0.11 2.2 7 steel 22.73 22.73 0.15 4.5 0.05 1.5 The testing results indicate that the height of soil plug seems well correlated with suction pressure and action time.

This cellulose was partly depolymerized, low in water content, white, tasteless and pure powder with the average grain size of 20μm.
When pyrolysis happened at 500°C for 5s, the products were mainly organic compounds with carbon number of 2-6.

Wei Xu [13] has employed glycol as reducing agent to synthetize evenly-proportionated globular nanometer Ni with average grain diameter 50~100nm.
Then add 200ml deionized water and stir, and add the citric acid of the number of moles of 2 times metal oxygen ion.

Namely, it is known that the electrochemically active surface of porous structure is distinguishable from outer (directly facing the electrolyte) and inner (pores and loose grain boundaries) parts.
At the highest concentration, the impregnation of carbon surface is dominant, with simultaneous decrease in the number of oxide particles deposited in the intergranular space. 4.

Most specimens showed increased compressive strength when mixed with mono-dispersed grains (Fig. 5).
Acknowledgement This research was supported by the Public Welfare & Safety Research Program through the National Research Foundation of Korea (NFR) funded by the Ministry of Science, ICT & Future Planning (Grant number : 2013M3A2A1067159) References [1] A.