Search results

Introduction The functional tolerancing of mechanisms has now become well accepted in industry since this approach contributes to a reduction of manufacturing costs while improving product quality [1].
The functional requirement is thus expressed by the acceptable limits of an ending geometric entity related to another or to a datum reference system built from several geometric entities of the mechanism.
For a position tolerance of the cylinder axis related to a datum reference system (Fig. 2), the tolerance zone is a cylinder of diameter t, the deviation torsor comprises four components: D={tx, ty, 0; rx, ry, 0}.

Error percent was calculated to reach the accuracy of ANN model in head acceleration prediction by Eq.1: (1) Table.1 The average of error for eight signal examples Example Number 1st 2nd 3rd 4th 5th 6th 7th 8th Percent Average of Error 0.39 3.5 0.8 0.31 0.41 2.11 1.59 2.25 Accuracy of estimation for head acceleration in this study is near to ANN model for spine and head oscillations which was represented by Gohari et al. [10] based on experimental data.
Dong, Vibration characteristics and hand transmitted vibration reduction of walking tractor.

Since the rubber used is almost incompressible, I3 = 1, the expression can be reduced to (2) The material parameter of the rubber introduced in the Ansys Workbench data properties can be expressed in terms of initial shear modulus G and initial bulk modulus K where G = 2(C10+C01) and D1 = 2/K.
Abdelhafid, Effects of seismic isolation in the reduction of the seismic response of the Structure, International Journal Of Applied Engineering Research, 2.2 (2011) 290–295

. %) Steel C Si Mn P S Cr Ni Cu LCS 0.63 0.60 0.31 0.031 0.016 0.011 0.01 0.012 PS 0.12 0.22 0.37 0.023 0.015 0.011 0.01 0.009 A serial of isothermal compression tests were carried out at a Gleeble 3500 thermomechanical simulator in the deformation temperatures ranging from 1073 to 1373 K at an interval of 100 K, the strain rates of 0.02, 0.1, 1 and 10 s-1, and the height reduction of 60%.
During the isothermal compression, the flow stress-strain curves, which are the essential data in computation of the SHE, were recorded automatically by the microprocessor of Gleeble 3500.

Figure 1: Schematic representation of 90nm device Local Interconnect Contact Figure 2: RCVCC, one of the Electrical parameters data trend based on the previous lot results (Bold line is spec high) Due to RCVCC (Vcc Contact Resistance) failure and other factors, the device being developed did not exhibit repeatable yield and failed 100% site yield when using the POR clean.
Results and Discussion Processed wafers were subjected to a series of physical analyses including SEM inspection, etch rate qualification, pattern damage inspection and defect reduction.

Photochromic diarylethenes undergo reversible photoinduced cyclization/cycloreversion reactions between two isomers upon irradiation with UV and visible light, the two isomers of diarylethenes differ from each other not only in their absorption spectra, but in many physical and chemical properties including geometry, refractive index, as well as oxidation/reduction potential, etc [3].
Sincerbox: Holographic Data Storage (Springer-Verlag, New York 2000) [3] Y.

The absorption in the multilayer and the base would cause reduction of the transmission for UV, but it will be avoidable in case of the design for SSPS which needs the reflection also for UV.
Table 2 Data for TiO2, SiO2 and TiO2-SiO2 composite films.

Element diffusion, magnetic dilution and defect reaction between ferroelectric and ferromagnetic phases are main reason for the permittivity reduction of sintered ceramic compared with pure PT [13].
The data show that the saturation magnetization increases linearly with an increase in x.

Results Analysis According to the boundary conditions, the various data of gear is obtained.
This is mainly because that the spiral bevel gear is point contacting in contact process, the local temperature rises due to friction, and thermal expansion increases the contact area, as a result, the gear stress areas increase, leading to the reduction of the tooth surface contact stress and bending stress.

Locating CNTs have been also obtained on prepatterned substrates with different methods, such as offset printing [13], lithography [14-16], using reduction potentials [17].
Taken together, XPS and Roman data suggest that SWCNTs were successfully functionalized with hydroxyl and carboxyl by mixture acid oxidation.