Search results

Then, the deformed mesh characteristics (stored energy, spatial location and crystallographic orientation) can be taken as input data in a Monte Carlo model in order to link the results with nucleation and growth mechanisms during primary recrystallization [3].
Then, a cold rolling is simulated at a constant reduction rate at room temperature to a reduction of 40 % using the ABAQUS software.

The existing data are inadequate to establish their relative importance and further work is required.
Moreover, its efficiency also depends on the content of material added and its capacity in the reduction of Ca(OH)2 content.
In this study, it appears that the replacement rate (% mass) from which the reduction in expansion by DEF is efficient is 15% for FA, 10% for MK, 40% for GGBS and 10% for SF.

A very good example is the early ULSAB project started in 1995 and leaded by the principal steel makers to develop new advanced steels where a 25% of weight reduction was possible keeping the structural behavior.
Characterization of the solution heat treatment Aiming to optimize the future industrial process of the W-temper forming strategy, as received material was longitudinally cut in small pieces of 100x20 mm and solution heat treated using different oven temperatures and times. 470ºC was proven to be a good compromise for the reduction of the hardness in a small time.
Each hardness data represents an average measurement of three through-thickness measurements from three different parts treated at the same conditions.

The reduction of these vibrations is a common way to address the problem [6].
The measured data is analysed and processed on NI Signal Express software.
The machine's vibration amplitude using damping system shows the reduction of 75.3%, compared to that using the non-damping system in the same machining conditions.

Therefore, the sensitivity of tapered POF towards environmental changes will increased due to the reduction in fiber diameter that can strongly enhancing the evanescent wave [2].
The diameter reduction is essential to increment the sensitivity of sensor compare to the bare POF.
Interface B Outer medium Evanescent Field Interface A Figure 6 Sensing mechanism of modified cladding region Table 2 shows the data interpretation of output power for 20 mm of ZnO coated POF to detect the methanol concentration that range from 0 to 50 v/v%.

The model is tested against external data showing a high level of accuracy.
[9] Rajan Filomeno Coelho, Piotr Breitkopf, Catherine Knopf-Lenoir, Pierre Villon Bi-level model reduction for coupled problems.
Model reduction for multidisciplinary optimization application to a 2d wing.

In contrast, the cost reduction of the VRFB by improvement of the current density [18] with lower internal resistances, e.g., the mass transport resistance and the reaction resistance, is still required for its commercialization.
From the aforementioned data, the fraction of Uloss in the discharged energy was 4.0% for both the unloaded electrode and the composite-upstream electrode.
Nogami, Mechanism of Dioxovanadium Ion Reduction on Oxygen-Enriched Carbon Surface, J.

Herzberg was the systematization of data about the kinds of stress-strain curves for materials with different types of crystal lattice and the structural state [1].
This stages characterized by a reduction of diagrams = f (e), associated with the localization of deformation.
Macrolocalization deformation, accompanied by formation of a neck, usually leads to a significant reduction in the activity of AE until complete disappearance.

There was no occurrence of large M6C carbides in this case, and the carbides on the grain boundaries showed no serious aggregation and coarsen, so the tensile strength at room temperature did not produce a dramatic reduction.
However, it is apparent that there was the largest reduction calculated to be about 8.8% of the as-received tensile strength at high temperature after aging for 500h compared to that of 1000h and 3000h, which indicates that the bainitic lath microstructure plays an important role in the high temperature tensile strength.
[8] NRIM Creep Data Sheet No. 38, NIMS (formerly NRIM), Tsukuba, 1986 (in Japanese)

This work interested in reduction of the strong acidic sites of HZSM-5 for improvement of the catalytic activity for methanol dehydration.
Brückner, Reduction of N2O with CO over FeMFI zeolites: influence of the preparation method on the iron species and catalytic behavior, J.
Pitfalls and limitations in gas adsorption data analysis, Micropor.