Search results

The general control structure In Fig. 5, the element TP(M) signifies the technological process (TP), in this case the d.c. motor (M).
This variant is more expensive due to the necessity of using more equipment comparing with the case of a simple control structure.
It can be remarked that contains a PI and a PID structure connected in series.
The modeling procedure of the d.c. motor and of the elements used in the control structure is presented. 2.
Modeling and Simulation, Russian Journal of Physical Chemistry, 85, 4 (2011), pp. 549-556

Factors such as particle size, morphology, and surface chemistry are critical determinants of nanoparticle-induced toxicity [10].
Despite TiO₂ broad use in dermatological products, its interactions with 3D cell culture models such as spheroids - structures that mimic in vivo tissue organization - remain underexplored [8, 9].
The structure of the TNTs was characterized by X-ray diffraction (XRD) D8 FOCUS diffractometer (Bruker, Billerica Ma, USA) with Cu-Kα radiation (1.5418 Å).
The Ti2O crystalline structure of the TNTs was found in the XRD pattern, this type of titanium oxide has only been reported in in vitro assays by our research group.
Even after 72 h of continuous contact, which included the UV exposure period, the spheroids retained their normal structure and morphology, with no evidence of disintegration or abnormal compaction.

The deposited material is quickly cooled at room temperature, solidifies, and joins the previously extruded structures.
The specimens filled with 50% (%w) showed greater preservation in the structure, showing greater mechanical resistance for this percentage of polymer.
Figure 5.B illustrates the specimens filled with 50%, by mass, and it is possible to observe greater preservation of the structure after the compressive strength test.
Specimens with 100% filling had a greater drop in Young's modulus, showing greater deformation in the structure (260% greater than 30% filling), behaving as a very tenacious material.
Evaluation of 3D printing mate-rials for fabrication of a novel multi-functional 3D thyroid phantom for medical dosimetry and image quali-ty‖, Radiation Physics and Chemistry.

Odriozola 6 1 Department of Chemistry, Universidad Autónoma Metropolitana-Iztapalapa, Av.
Among the ordered mesoporous silica structures, SBA-15 possesses an hexagonal array of mesopores of 6.0 nm in diameter, approximately; which is much larger than the 3.0 nm pores characteristics of the MCM-41 structure reported previously for drug delivery [12].
It has been described that the characteristics of porosity of the SBA-15 depend on the way in which the micellization of copolymeric surfactants are prepared to generate an specific structure.
These results suggest that the ordered structure was not completed in this sample.
The mesoporous structure of the BINOM-Silica-2 and BINOM-Silica-4 samples is clearly different from those above described, the first sample, BINOM-Silica-2, shows a multimodal porous structure and the second one, BINOM-Silica-4, show a type H2 hysteresis loop that points to a porous system in which the distribution of pore size and shape is not well-defined.

The organization of this paper is depicted as follows: Section 2 makes a brief description of the small-scale unmanned helicopter physical characters and device, and introduces the 13-order model structure.
The structure of matrix A, matrix B presents below.
The model structure (1) could be observed through some tips.
With the model structure (1), acquisition of model parameters within acceptable time, which have high agreement with real flight data, is the pursuit of identification method.
Physics and Chemistry of the Earth, 2002.

It shows that the most of particles have a spherical structure.
The crystal structure of the ZnO fabricated in this work had a hexagonal wurtzite, according to the XRD analysis.
Furthermore, SEM investigations for the ZnO/Ag/SiO2 revealed that the morphology with sphere-like structure can be observed.
Tasbihi, Preparation, characterization, and application of ZnO@ SiO2 core–shell structured catalyst for photocatalytic degradation of phenol, Environ.
Iler, The chemistry of silica: solubility, polymerization, colloid and surface properties,and biochemistry, Wiley Interscience, New York, 1979 [23] H.

So, with an increase in the iron content in the coating, the formation of a finely dispersed structure increases.
With increasing process temperature, the structure of the coatings becomes more coarse.
Zinc-iron coating structure with iron content in the coating = 40% x 500 Figure 10.
Structure of the zinc-iron coating, obtained at an electrolyte temperature = 90 0С х 500 a) b) Figure 11.
Laboratory workshop on electrochemical coating technology, Moscow, Chemistry, 1980

In recent years considerable research has been carried out on carbon structures to be used in reversible absorption-desorption systems [4].
The hexagonal boron nitride (h-BN) is an artificial ceramic whose structure is very similar to graphite or high surface carbon derived powders.
The layer structure of BN is clearly identified on the darker parts of the micrograph.
These low values of the hydrogen storage obtained in spite of a large surface area of the BN powders can be related to the two kinds of pores present in the structure.
The important nanoporosity seemed to be inefficient in the storage which only realised into the mesoporous structure.

The CeO2 nano fibers and nano cubes are of pure cubic phase (fluorite structure, JCPDS 4–0593, space group Fm-3m; lattice constant (cubic) = 5.4110 Å).
X-ray photoelectron spectroscopic studies XPS is a powerful technique for surface compositional analysis of nano-structured materials.
Low band gap value gives an indication of densely packed crystalline structures.
Formation mechanism In order to understand the formation of the cubic structure, the effects of hydrothermal temperature on the morphology of the products were further investigated.
Tret’yakov, Synthesis of nanocrystalline ceria colloids in nonpolar solvents, Doklady Chemistry 430 (2010) 24-26

The lime was hydrated, and reacted with the ash to cement the whole structure together.
CSH in modern concrete resembles a combination of naturally occurring layered minerals, called tobermorite and jennite, however never with ideal crystalline structures.
Structure Magazine, January 2009:11-15
Czarnecki, From microstructure to macrostructure: an integrated model of structure formation in polymer modified concrete.
RILEM Materials and Structures, vol 38, nr 280, 2005, p 601-607