Search results

Dimensional data was also taken to understand springback rates and understand if the predicted compensation worked.
The vehicle is an all aluminum body and frame to maximize weight reduction to improve vehicle range on electric battery only mode.

Tab.2 Model best fits and root mean square error Linear model Non-linear model Hammerstein model Matching Degree 79.98% 88.69% 97.36% RMSE 0.0793 0.0420 0.0124 Compare the output curve in Fig.4 with the input data curve in Fig.3 (a), the experiment output has stronger clipping effect in 2, 6 and 16s, compared to input signal.
The reduction of stick-slip friction in hyraulic actuators [J].

Nevertheless, the construction made with fire retardant are also stain, pursuing different goals: to provide signal-warning and identification functions by applying the appropriate color; increasing the life of the fire-retardant coating; giving special properties, in addition to flame retardants, due to the topcoat; reduction of pollution on a white surface [10].
As a result, for the construction of structures of industrial buildings and structures are almost always makes sense to use fire retardant coatings improve the fire resistance of data structures using it colored topcoat, not flame retardant.

Heat treatment of deposited products does not always lead to the required degree of residual stress reduction.
Strip type n×(mm×mm) Layer Composition of chemical elements, % by weight C Mn Si Cr Ni Mo N 1 Soudokay 308 L (60×0.5) + Record BLT 101 1 0.035 3.20 0.60 22.35 18.12 1.40 0.10 2 0.028 3.60 0.50 23.00 21.30 1.90 0.12 3 0.025 3.89 0.26 24.61 22.30 2.10 0.12 4 0.021 4.50 0.15 25 22.30 2.10 0.14 2 Soudokay 308 L 2×(60×0.5) + Record BLT 101 1 0.029 3.60 0.52 22.17 19.91 1.70 0.13 2 0.022 4.40 0.17 24.90 22.30 2.07 0.13 The chemical analysis data given in Table 2, indicate that when using two strip electrodes, a deposited layer with a chemical composition identical to the electrode material can be obtained, as with electroslag welding, already in the second layer [15-17].

BSE images and EBSD data were obtained from the longitudinal cross section surface of the samples which were mechanically ground on abrasive papers containing SiC particles to a level of 4000 grit and then polished to 1μm.
The reduction rate grain size during the third and fourth pass was slower than the second pass.

Study of surface metrology in nano range is becoming more commonplace in many applications and research environments as well as data treatments dealing with standardized rules.
R2 is a measure of the amount of reduction in the variability of Y obtained by using the model.

For adequate use of Central Angle theory, it is useful to consider reduction methods that can relate two defined power systems based on power flows, line and susceptances; and involving voltage angles in the boundary buses.
Salazar, "Synchronized Phasor Data Based Energy Function Analysis of Dominant Power Transfer Paths in Large Power Systems," IEEE Transactions on Power Systems, vol. 22, no. 2, p. 727–734, May 2007

Experimental study on seismic response of shear wall structure, not only can provide necessary parameters for theoretical analysis, but also can obtain abundant experimental data.
According to Table 5, due to the influence of soil, the seismic wave from the table has reduced, that is, the seismic wave input to the table has a great influence toward the upper structure, the frequencies in two direction have reduced 71.9% and 76.3% respectively, the direction in which lateral stiffness is higher has a greater reduction on frequency, that is 76.3%.

The reasons for the development of cracks in large-diameter grinding balls are defects of metallurgical origin of non-continuously cast billets with a small cross-section (shrinkage and gas porosity), which are not completely eliminated during rolling due to the low degree of reduction and structure elaboration [9 - 20].
Franek, Data processing of measured surface temperatures of continuously cast billets and blooms to verify the numerical solidification model, 29th International Conference on Metallurgy and Materials, Brno, Czech Republic, 2020, pp. 80-85

In technical literature, there are several papers presenting experimental data, analytical and numerical models about masonry columns confined with FRP[7,8] using different type of masonry (natural stone, tuff, clay brick) and fibers (carbon, glass, basalt); on the contrary, very few recent works concerns the axial behavior of FRCM- confined masonry columns[9].
The constitutive law is able to take into account the increase of the strength according to Selby and Vecchio [12] and the lateral crack effect according the relationship of Vecchio and Collins [13] about the reduction of the compression because of the large tensile strain perpendicular to the principal compressive direction.