Search results

Hot rolling at 460°C followed by cold rolling with a reduction of 40% provides achieving superplastic elongation-to-fracture of 320% at a temperature of 500°C and ε̇=5×10−4 s−1 in an Al-6%Cu-0.8Mg-0.6%Ag-0.15Zr alloy [5,6].
All misorientation maps were obtained with a sufficient level of indexing to provide reliable data.

The effectiveness of any such residual stress reduction strategy was proven by many destructive as well as non-destructive techniques [8].
The Opium NIM module was programmed to synchronise the acquisition of the MCA data and the operation of the welding unit.

The SHPB had a high-strength 12 mm silver steel roll diameter and a striking plate, incident panel, transmitter plate, sample tester and data acquisition system (Fig. 1).
Nevertheless, the reduction in peak stress and stress of recycled mortar specimens may include single and hybrid fibre in recycled mortar, given the results of adverse effects of the use of recycled mortar.

Two partial pressures of oxygen were used to evaluate the impact of changing oxidation-reduction conditions on slag-refractory interaction reflecting the variation in synthetic gas composition inside of gasifier.
Experimental data on the slag-refractory interaction will be incorporated into mathematical model that will be used to 1) identify critical conditions at which refractory corrosion sharply increases, and 2) predict the service life of a gasifier refractory.

Using the method reported in [12], the loading curve can be represented in the system of functional logarithmic coordinates as ln(s-s0)=f(lne) (here s is the true stress which takes no account of the reduction in the work cross-section and e is the true deformation).
The quantitative data on mechanical characteristics and deformation stages of alloys are listed in the Table 1.

The reduction of the oxidized sensitizer dye by the electrolyte is in competition with the unfavorable recombination of the injected electron with the oxidized dye [10].
Based on the data listed, the best annealing temperature for anatase TiO2 photoanode is at 420 oC (0.094%) with the crystallite size of 18.76 nm and average particle size of 19 nm that is favorable for the dye attachment and thus enhances the energy conversion efficiency of the DSSC.

.% composite powder was synthesized by using vacuum in situ reduction and carburization reactions[5-7], the composite powder composite powder molding into flan of cutting inserts under the pressure of 150MPa. 
Continuous Cutting Test Experimental Conditions.Tool life is the most basic and most important criterion to judge the performance of a cutting insert materials, it is mainly obtained through the tool wear test data.

Results given in Fig.3 shows at the first sight positive results of sound insulation DnT,w of facade walls or as a case may be windows in ventilation position considering health protection when comparing to above quoted data according to WHO [11] or given in relation to (1), where soundproofing indicator of slightly open window of value Rw = 10 to 15 dB is considered for window.
Following suggestions and facts may contribute to higher level of prevention and reduction of health risk from stress factors in new built residential building in the future: • Concurrence of conflicting requirements at so called hygienic window may concrete pressure for projecting buildings with so called quiet facades [18] and legitimate need to define quiet areas and zones connected with park greenery and better use of anti-noise barrier building in accordance with the mission and objectives of Directive2002/49/EC [10] in urbanism

Statistical Analysis: The data were expressed as the mean ± standard deviation (SD).
However, chain scission of the scaffold irradiated by 50 kGy make macromolecular chains breakdown to occur small molecule segment which begin to decompose at 320°C[11] and the high-energy irradiation in air lead to progressive reduction in molecular weight and eventual degradation to non-polymeric materials to some extent.

So, it reduces the operation time and leads to overall value reduction.
Methodology and Data Collection. 3.1 One Factor at a Time Approach The experiments were conducted by victimization of One-factor-at-a-Time-Approach and L9 mixed level in which, one input parameter is unbroken constant and every one alternative parameters are varied.