Search results

Materials Science and Engineering: A, 507(1–2) (2009): 102-109
Materials & Design, 42(2012): 418-423
Materials & Design, 57 (2014): 315-324
Materials Science and Engineering: A, 488(1) (2008): 281-295
Materials Science Forum, 817(2015): 621-626.

Devine* 1 Materials Research Institute, Athlone Institute of Technology, Athlone, Co.
Westmeath, Ireland Email: ychen@research.ait.ie 2 Materials Research Institute, Athlone Institute of Technology, Athlone, Co.
Since PCL is a ductile material, the two materials were blended together in an effort to improve the mechanical properties.
EXPERIMENTAL 2.1 Materials PLA was obtained from NatureWorks LLC, Ingeo biopolymer 7032D.
Biodegradable polymer blends of poly(lactic acid) and poly(ethylene glycol), Journal of applied polymer science, Vol. 66 (1997), pp. 1495-1505

The materials for preparing bimetal strips with cold roll bonding should have a good plasticity.
To meet the critical reduction, the materials for cold roll bonding therefore should have a good plasticity.
References [1] Yang Liu, Wenjing Shang, Hongfang Liu, Zhigang Huang, Applied Mechanics and Materials, 2012, 184-185(1): 959-962
[2] Gyeong Tae Kang, Jae Sook Song, Sun Ig Hong, Advanced Materials Research, 2014, 951(1): 83-86
[7] Wei Cai, Zao Qi Hu, Hong Fang Liu, Advanced Materials Research, 2011, 194-196: 1347-1351.

Potential of induction of heterogeneous nucleation of apatite on substrate materials is an important parameter to achieve a successful coating of apatite.
Hydroxyapatite coating on organic polymers is an attractive way to develop such hybrid materials.
Potential of induction of heterogeneous nucleation of apatite on the substrate materials is an important parameter to achieve a successful coating of apatite layer.
Materials and Method Four types of sericin were obtained by extraction from raw silk fiber under various conditions.
Acknowledgement This work was conducted under the auspices of the research project, "Technology Development for Medical Materials Merging Genome Information and Materials Science", in the Kansai Science City Innovative Cluster Creation Project, supported by the Ministry of Education, Culture, Sports, Science and Technology of Japan.

“Innovation is the soul of the development of science and technology”, the development of the tobacco industry also needs constant innovation.
This is the main cause of uneven material liquid.
Journal of Zhengzhou Institute of Light Industry (Natural Science Edition), (2011), No. 2, p.26 [3] State Tobacco Monopoly Administration.
Tobacco Science and Technology, (2003), No. 6, p.75-90 [5] Chen Liangyuan.
Zhengzhou: Henan Science and Technology Press, (2002)

Combination of the two, materials can be selected. 
References [1] School of Metallurgy and Materials Residual stresses at the surface of automotive suspension springs.
Journal of materials science ,35 (2000), pp.3313-3320
[4] Kotaro Watanabe, KMasahi Tamura and Ken Yamaya: Journal of materials processing Technology,Vol. 111 (2001), pp.132-134
Last spring production process design and optimization of new materials, new technologies and new standards for product quality inspection applications and practical manual.

Experimental results Different sensors based on three kinds of materials are tested respectively, the results is shown in Figure 3, where material 1 stands for NBR, material 2 stands for HDPSF and material 3 represents PTFE.
Experimental results of three kinds of materials Under the condition that the microbending degrees are in same level, the greater the elastic modulus of a gasket is, the wider the range of the sensor measurement can be achieved accordingly.
Acknowledgement This project is subject to natural science foundation of Heilongjiang province (project number: ZJG0607-02).
Journal of Beijing university of posts and telecommunications, 1994 (1): 56-58
Du, Multifunctional fiber optic smart composite materials research [J], Journal of composite materials, 2000 (1): 37-42.

Industrial water jet has a wide working pressure range, therefore the nozzle materials of water jet are various.
The working pressure of the industrial water jet is comparatively higher, and commonly used nozzle materials are blue diamonds, red diamond and diamond. [8] Blue diamond, whose using life is about 50 to 100 hours on a good water quality condition and lifetime is half of it when adding sands to water, is one of the most commonly used material, is artificial single-crystal gem and is good at jet quality.
Military Medical Science Academy of the PLA AMMSInstitute of medical equipment2009.5.22.
Journal of Engineering Design,2003.12.
“Water jet theory and technology”.China Safety Science Journal,1999.10 (In Chinese)

Flame retardant low density polyethylene with aluminium hydroxide/ commercial fire retardants FR01 synergistic system Nina Wang1,a, Dinghan Xiang1,a, Pinshu Mo1,a,Yi Lu1,a 1College of Materials Science and Engineering, Guilin University of Electronic Technology, Guilin 541004, China axiangdh@guet.edu.cn Keywords: flame retardant; LDPE; Aluminium hydroxide; thermal stability Abstract.
Many fire accidents caused by polymeric materials, there was 150 million RMB in property loss and more than 1300 fire-related deaths in China in 2008 [3].
Therefore, one focus of research in recent years has been how to improve flame retardancy of polymeric materials, such as EVA/LDPE [4].
China Safety Science Journal. 21 (2011) 54-59
Fire Safety Journal. 42 (2007) 232–239

In this paper, the model of the diamond coatings/WC interface is built by molecular dynamics simulation software Materials Studio with the modeling process as shown in Fig. 2.
Models with different interface scales built by Materials Studio are used to explore the influence of interface scales on the adhesive strength of diamond coatings/WC interface.
Journal of Chemical Physics.2010,59(8),5687-05 [9]Li Jun, Gule, Zheng Dezhi.
Molecular simulation of the mechanical properties of carbon nanotube/gold composite material[J].Rare Metal Materials and Engineering,2008,37(7),1217-1220 [11]W.Z.Lu, D.W.Zuo, M.Wang, et al.
WC-Co cutting tool inserts with diamond coatings.Diamond and Related Materials,1999(8)1913-1918