Search results

Wu et al. [36] showed that on the plasma etched surface, the white lines represented the cross-section of the GNP fillers and the contrast between GNP fillers and the matrix was better than the polished surface.
Du et al. [37] presented that uniform distribution and low aggregation of carbon fillers in polymer matrix caused a segregated network structure, resulting in high conducting network formation at low filler loading.
In addition, Gu et al. [41] revealed that strong interactions between polymer matrix and fillers may also cause greater activation energies of flow.
El Achaby, F.E.
El Kacem, M.

The Fe-Fe electrode combination had the highest removal efficiencies of the heavy metal ions of Fe-Al, Al-Fe, and Al-Al combinations.
The experiments were conducted by arranging Al-Fe, Al-Al, Fe-Al, and Fe-Fe electrodes.
So, the removal efficiency of Fe-Fe is highest than the removal efficiency of Al-Al, Al-Fe, and Fe-Al, but the electrode combinations of Fe-Al removal efficiency are greater than that of Al-Al and Al-Fe.
[18] Moussa, D.T., El-Naas, M.H., Nasser, M., Al-Marri, M.
El-Naas.

For his part, El-Sebaiietal [9] contrasted the temperatures of the outlet air and the absorber layer for the double-pass solar air heater configuration with the corrugated layer.
On the other hand, Wazed et al. [10] contrasted the forced and natural circulation of air in the solar air heater.
Driss et al. [15] studied the aerodynamic components of a building system fitted with a solar patio.
In another research study, Driss et al. [16] suggested an acceptable building environment to boost thermal comfort.
El-Sebaii, S.

[8] Karthk, V., et al.
[13] Bing, Li, et al.
[14] Kleiber, M et al.
[15] Bing, L et al.
[17] Koç, M et al.

Quested, A.L.
Vandyoussefi, A.L.
Results and Discussions Simulations were conducted for Al-Fe, Al-Mg, Al-Ti and Al-Fe-Mg alloy systems solidified under spatially isothermal condition.
Greer el al assumed that the Q values of different solutes in a multicomponent alloy are additive implying the same initial Q of different alloy systems should produce the same final grain size [1].
(a) (b) Fig. 3 The grain sizes measured by Spittle et al are plotted with 1/Q (a) and 1/R (b) for binary Al-Cu, Al-Zn, Al-Si and Al-Mg alloys inoculated with 2 PPT Al-Ti-B grain refiners.

Uematsu et al. [9], Cao et al. [10] and Reimann et al. [11] have discussed a refill technique applied to various types of material in different ways.
Sajed et al. [14] proposed a two-stage refilled friction stir spot welding (TFSSW) applied on Al 1100 sheets.
Materials and Experiments A 1.6-mm thick Al-clad sheet of Al-Cu-Mg alloy AA2024 in T3 condition was used in the current study.
The base material sheet has 100-µm thick Al-clad layer of pure Al on both sides.
SZ TMAZ Al-clad layer Fig.7.

Al Zn Mn Fe Cu Ni Be Mg MZY addition (wt.%) Ⅰ 9.0000 0.800 0.250 0.020 0.020 0.001 0.0018 Bal 0 Ⅱ 8.8900 0.820 0.248 0.018 0.018 0.001 0.0018 Bal 2 Ⅲ 8.8700 0.826 0.247 0.017 0.017 0.001 0.0018 Bal 4 Ⅳ 8.8500 0.830 0.246 0.016 0.016 0.001 0.0018 Bal 6 Ⅴ 8.8300 0.841 0.245 0.015 0.015 0.001 0.0018 Bal 8 Results and Discussion The microstructure and XRD analysis patterns of Mg30Zn60Y10 quasicrystals alloy which was prepared in normal casting condition are shown in Fig.1.
[13] E.l.

Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca.
The influence of particle size to Al, Si, P, S and Ca contents is shown in Figure 2.
The analysis of the distribution result shows that particle sizes of -150/+120 mesh have Al, Si, P, S, and Ca contents below 3.5%.
This is because there are impurities that must be eliminated such as Fe, Mg, Al, Si, and Ca trough the purification process.
[5] Abdel-Karim, A.M., Moustafa, M.I., El-Afandy, A.H., and Barakat, M.G., 2017, Mineralogy, chemical characteristics and upgrading of beach ilmenite of the top meter of black sand deposits of the kafr Al-Sheikh Governorate, Northern Egypt, Acta Geologica Sinica (English Edition) 91(4) 1326-1338 [6] Zhang, S., Cioppa, M.T., and Shihong, S. 2010.

According to the study done by Lin et al, we used Alg film as the carrier and chose 20mg/mL PTX as the highest dose in a pilot to determine the best PTX concentration Five mg/mL was chosen based on the MTT and ALP activity assays [13].
El-Massik, AGA.
El-Lakkany, M.
El-Lakkany, SS. el-Din, F.

Its electronic properties can be effectively tuned by external fields, atomic doping (B, N, P for p-type; Al for n-type), metal adsorption, hydrogenation, or oxidation.
El-Sayed, M.A.
El-Mansy, Electro-absorption of silicene and bilayer graphene quantum dots, J.
El-Sayed, M.A.
El-Mansy, Stability and electronic properties of edge functionalized silicene quantum dots: A first principles study, Physica E, 108 (2019) 339–346