Search results

Additionally, the construction of building involved the usage of building materials in various forms.
Materials and Test Methods Materials and concrete mixes Fly ash is abundantly available in Malaysia, since the use of pulverised coal firing remains one of the ways of generating electricity in the country.
American Society for Testing and Materials [9] BS EN 12350-2 (2009).
Effect of High Temperature on High-Volume Fly Ash Concrete.Arabian Journal for Science and Engineering, 38(6), 1369-1378
Construction and Building Materials, 76(2), 214-220.

The multilayers of Al2O3/TiO2 may combine the merits of both materials to show enhanced anti-corrosion property.
Darling: Solar Energy Materials and Solar Cells, Vol. 99 (2012) Sl, p.235
George: Acs Applied Materials & Interfaces, Vol. 3 (2011) No. 12, p.4593
Cai: Materials Research and Application, Vol. 5 (2011) No. 3, p.229
Nam: Journal of Vacuum Science & Technology A, Vol. 15 (1997) No. 6, p.2993

(2)Low-carbon material.This index shows whether to use low-carbon and reusable material in the process of building or not.
The evaluation focus on three indexes, they are local material, materials producing and reusable, and disposal of waste
Table 1 The evaluation system of low-carbon building Target layer Criterion layer Index layer The evaluation system of low-carbon building Low-carbon structure index (U1) Lighting system (U11) Heating system (U12) Flooring system (U13) Wall system (U14) Low-carbon material index (U2) Local material (U21) Building materials (U22) material reuse and waste disposal (U23) Low-carbon energy index (U3) Energy measurement and detection (U31) Collective heating (U32) Renewable energy utilization (U33) Clean energy utilization (U34) Low-carbon technique index (U4) Usage of low-carbon and new material (U41) New technology (U42) Usage of energy saving (U43) Investment of Intelligent electronic equipment (U44) Professional ratio of building team (U45) Low-carbon management index (U5) Greening rate (U51) Property service (U52) Waste treatment (U53) Operation management (U54) Establishment of model for evaluation system of low-carbon building Firstly, the evaluation factor set is determined.
Acknowledgements This work was financially supported by the2012 Housing and Urban-Rural Construction Department of Shandong Province Science and Technology Project (2012RK028) ,General project of Shandong Province statistical research key topics (KT12049) Reference [1] Liu CC, Qin FH, The research on development of low-carbon building[J].
Journal of Hunan University, 2012,(6):6

Metallurgy and Materials, 2022, 42(05): 25-26+29
Materials China, 2023, Vol. 42, No. 06, pp. 464-474
A new understanding of the effect of Cr on the corrosion resistance evolution of weathering steel based on big data technology, J.Journal of Materials Science and Technology -Shenyang-, 2021, 104
Advanced Materials Research, 2014, 989-994:420-424
Advanced Materials Research, 2009, 79-82:957-960

First, important issues about the common materials for CubeSat and potentially 3D printing materials for CubeSats are addressed.
Therefore, suitable materials must be selected properly to meet these requirements.
Published material property data for selected materials [14, 38].
In 3D printing, there is at least 20% of waste materials due to the raft and support materials.
Series: Materials Science and Engineering 608 (2019)

Materials and Methods Dielectric Material.
Key Engineering Materials 655(2015):132-135
Key Engineering Materials 697(2016):227-230
Key Engineering Materials 562-565(2013):33-38
Key Engineering Materials 697 (2016): 231.

Ishak1 1School of Materials Engineering, Universiti Malaysia Perlis, 02600 Jejawi, Perlis.
European Polymer Journal. 38(9) (2002) 1887-1897
Materials & Design. 41 (2012)131-141
Strong, Abrasion and Hardness, in Plastic Materials and Processing, S.
Strong, Flexural Properties, in Plastic Materials and Processing, S.

Working above limit temperature for long-term, metal materials of exhaust valve are likely to anneal, which leads to the great reduction in hardness of the valve materials, enlargement in deformation and wear of valve, and even to fracture.
The 21-4NWNb is chosen for the material of valve head, while 40Cr as material of the valve rod.
The property of two kinds of materials are as follows: the modulus of elasticity of the bar and the head are () and (), so as their poisson's ratios 0.277 and 0.3, their densities () and (), their coefficients of thermal expansions () and(), their specific heats ()and (), thermal conductivities 44.0 () and 14.5 ().
Journal of Mechanical Science and Technology.
Journal of WuHan University of Technology. 2002,24(3): 33-36.

In addition, the SAM layer can be expected to act as an adhesion promotor with metal materials.
In addition, the SAM layer can be expected to act as an adhesion promotor with metal materials.
Mor, Journal of Vacuum Science & Technology B 20, 1334 (2002)

Research on the Color Models of the Heat Transfer Printing Paper Linghua Guo 1, a, Meiyun Zhang 1, b, Xinhua Guo 2, c and Qian Zhu 1,d 1 Shaanxi university of science &Technology, Xian 710021, China 2Jinan University, Zhuhai 519070, China a guolinghua318@126.com, b myzhang@sust.edu.cn c xinhua008@sina.com, dzhuqian520@126.com Keywords: transfer printing paper; color gamut; color tone; quality evaluation Abstract.
Experimentation Experimental material.
The printing materials are chemical fibers which are different from the paper on the ink receptivity[11].  
Acknowledgements This work was financially supported by the Shaanxi provincial Education Department Special Science Foundation (2010JK424),Shaanxi university of science &Technology Science Program (ZX10-02).We also thank the ShaanXi university of Science & Technology and JiNan University for their experimental equipments.
Graciela and R.John: Journal of Imaging Science and Technology Vol. 47 (2003), p. 296~303 [3] Xianhong Zhang: China Forest Products Industry(in Chinese )Vol. 33(2006),p. 39~41 [4] Xinyao Chen, CHINA.