Search results

The line scan and element mapping of Mg, Ti, O and Al are shown in Figs. 6b and 6c.
Mg Ti O Al Figure 6b.
Mg Ti O Al Figure 6c.
The elemental mapping of Mg, Ti , O and Al at the location indicated in Fig. 6a.
Wartman, and E.L.

Such a calibration was developed by Kruger et al. [3] for austenite grain sizes in a wide range of C-Mn steels assuming n=3.
It has been shown by Sarkar et al. [5] that cylindrical samples can be used for laser-ultrasonic measurements during and after hot deformation.
For example, the work by Sarkar et al. [5] on recrystallization (see Fig. 7) led to propose a revised equation for the recrystallized grain size as a function of initial grain size, applied strain and temperature.
Subsequent grain growth is affected by Nb in solution and Sarkar et al. [5] showed that the grain growth rate can be described by (5) where M is the grain boundary mobility, g is the grain boundary energy and P is an effective pinning parameter.
Vol. 42 (2000), p. 867 [2] E.L.

[2] Xu H, Hashimoto K, Mukaigawa T, et al.
[3] Gim Y,Hudson T,Fan Yet al.Microstructure and dielectric properties of Ba1-xSrxTiO3 film grown on LaAlO3 substrates.
[4] ZhuW,WangC C,AkbarSA, el a.l Fast-sintering of hydrother mally synthesized BaTiO3powder and their dielectric properties [J].
[6] Chen J G,Tang J,Meng X J,et al.Fabrication and characterization of pyroelectric Ba0.8Sr0.2TiO3 thin flims by a sol-gel process [J].J Am Ceram Soc ,2001,84(7):1421–1424
[10] AYYUB P, PALKAR V R, CHATTOPADHYAYS, et al.

A Comparative Study of Hydromechanical Properties in Saturated and Partially Saturated Conditions of Two Soils from the Runway of Oran Airport CHIKHAOUI Mohamed1,2, a*, HOXHA Dashnor2, b, BELAYACHI Naima2, c and NECHNECH Ammar1, d 1LEEGO, FGC, USTHB, BP 32 El-Alia, Bab-Ezzouar, Algeria 2Univ.
Equally, the thermal conductivity received special attention by Low et al. [5].
Mertens et al. [9] found out that the distributions over all locations are significantly different in regard to all parameters at a 5% level. 
While relative permeability test are performed following procedure proposed by Homand and al. [12], for the sake of simplicity and because the absence of equivalent measurement in situ, the results of these tests are not discussed here.
Al-Barri, and W.

Nakayama et al. [6] reported that apatite-type structure of compositions Ln10-xSi6O26+y (Ln = La Sm, Nd, Dy, Gd, x = 8 to 11) materials exhibited ionic conductivity.
Tao et al. [17] reported that the relative densities for La10Si6O27 sintered at 1400 0C for 20h and for a three day period have resulted in densification of 69% and 74%, theoretical density respectively.
El-Koury, et al.
Zhang et al., Low temperature solid oxide fuel cells based on Sm 0.2Ce0.8 O1.9 films fabricated by slurry spin coating, J Power Sources 159 (2006) 637-640
Aono, et al., Ionic Conductivity of Lanthanide Silicates, Ln10(SiO4)6O3 (Ln = La, Nd, Sm, Gd, Dy, Y, Ho, Er and Yb), J.

Kiehn,et al.: the Lancet.
Chen, et al.: J.
Kim, et al.: Materials Transaction JIM.
Vol. 47 (2002), p. 1359 [6] L.El.
Rocher, et al.: Biomolecular Engineering.

References [1] Agrawal A, Kumari S, Bagchi D, et al.
[6] Nikolić N D, Pavlović L J, Pavlović M G, et al.
[10] Cifuentes L, Castro J M, Crisóstomo G, et al.
[11] Soliman H, El-Moneim A A.
[14] Popov K I, Krstić S B, Obradović M Č, et al.

Therefore, the phytoremediation needs to be improved for example with the help of electric current (electro-assisted), which then known as electro-assisted phytoremediation (EAPR) Putra et al. (2011) [2].
The application of EAPR on the removal of Cd in the aquatic plume was first reported by Bi, et al. (2010) [3] using Lactutasativa.
Another EAPR study was reported by Kubiak et al. (2012) [4] showed that the significant absorption of As (> 90%) by Lemna minor.
In addition, the chlorophyll concentration was also measuredat the end of an experimentusing acetone extraction of spectroscopy analysis.The copper and iron concentration in the acid extract was determined by a flame atomic absorption spectrophotometer (PinAAcle 900 Perkin Elmer, USA) according to Putra et al. [5].
El-Alawi, D.M.

., et al. [4] reported the synthesis of cordierite from andalusite.
K., et al. [5] applied mechanical force by attrition milling on the synthesis of cordierite.
Yalamac, E. and Akkurt, S. [6] used kaolin, talc and Al(OH)3 as raw materials for cordierite synthesis and investigated the effects of raw mixture milling parameters on the final product.
Endothermic reaction peaks at 556°C and 704°C in un-milled precursors corresponded to decomposition of talc to enstatite and silica. [8, 10] In milled precursor, decomposition peak of talc shifted to 505°C due to the influence of milling process. [6] Similar results were reported by Benhammou, A., et al. and Goren, R., et al. [4, 11].
El Hafiane, A.

The thermoanalyzer was calibrated on the melting point of Al standard.
Zandbergen, et al., Transformations of gold nanoparticles investigated using variable temperature high-resolution transmission electron microscopy, Ultramicroscopy. 110 (2010) 506–516
Zhang, et al., Size dependent melting behaviors of nanocrystalline in particles embedded in amorphous matrix, J.
Dong, et al., Size-dependent melting properties of tin nanoparticles, Chem.
Sedoi, et al., Productions of ultra-fine powders and their use in high energetic compositions, Propellants, Explos.