Search results

Results and discussion Fig. 1 shows the typical SEM images of the deposits prepared by electrochemical deposition at the current density of 10mA/cm2 and pH value of about 2 on the ITO glass.
Fig. 1 SEM images of deposits synthesized by electrochemical deposition on ITO glass at current density of 10mA/cm2 and pH value of about 2.
Fig. 4 SEM images of deposits synthesized by electrochemical deposition on ITO glass at pH value of about 2 and current density of 1(a), 5 (b), 15 (c), and 20mA/cm2 (d).
References [1] A.P.
Xiao: Material Science Forum Vol. 475-479 (2005), p. 3579 [11] B.P.

The optimal classification hyper plane, refers not only to all the training samples for accurate classification, and can make the distance classification hyper plane point nearest to the plane of the largest distance, As shown in Figure 1： H1 H H2 Fig. 1 The Optimal Hyperplane In Fig.1, H is classification line of the two classes of samples the inerrant separate. , are lines through two kinds of samples from the classification with recent samples and parallel to the linear classification respectively.
References [1] Pan Quan,Yang Feng,Ye Liang et al.
Journal of Harbin Institute of Technology. 2006,13(1):113-117
Machine Learning and Applications (ICMLA), 2010 Ninth International Conference on: 479 – 484
Machine Learning Journal 2009, 77(1):27-59.

Figure 3 shows the XPS results for InP for a H2SO4/H2O2 solution of pH 1.
Figure 1: Etching kinetics measured by ICP-MS for GaAs and InP in acidic H2O2 solution.
References [1] N.J.
[2] J.A. del Alamo, Nature 479 (7373) (2011), p. 317
Technol, 3 (1) (2014), p.

Two atomic structures with different metal/insulator interfaces are shown in Fig.1.
Table 1.
The results were shown in Table 1.
References [1] T.
Forum Vol. 475-479 (2005), pp. 2255.

Start timing after the five test-tubes were laid until detonate, (see Fig.1).
Fig. 1 Deflagration Results and Discussion The stabilizer contents (Ak II and Res) of the samples were measured by GC.
All measured values by GC and methyl-violet test are listed in table 1-3.
411 413 413 1 1.07 1.60 401 403 404 404 406 3 1.10 1.60 394 395 397 399 401 5 0.92 1.57 386 387 387 390 391 7 0.83 1.60 380 382 384 384 389 9 0.71 1.60 370 373 373 378 379 11 0.60 1.59 357 357 359 361 364 13 0.40 1.56 337 337 338 340 342 Scattering Field Of Methyl-Violet Burst Times From table 1-3, it can be found that the repeatability of the tb is good for same ta.
References [1] Jiang Jin-yong, Lu Gui-e, Su Zhen-zhong, et al.

The AFM image of ITO nanocolumns prepared at different substrate temperatures are shown in Fig.1.
The roughness average and peak-to-valley are listed in Table 1.
(b) (a) (d) (c) Fig. 1, AFM 3 x 3 µm 3D image of ITO nanocolumns sample deposited at a substrate temperature of (a) room temperature, (b) 100°C, (C) 200°C and (d) 300°C Table 1, Numerical analysis of AFM 3D image.
References [1] I.
Adesida, Properties of R.F. magnetron sputtered cadmium-tin-oxide and indium-tin-oxide thin films, Thin Solid Films 479 (2005) 223-231

Fig. 1 Increase of Deflection Due to Crack in Dapped-end.
This can result in developing of a crack if sufficient stiffening is not provided (Fig. 1).
Table 1.
Component Amount [kg] Aggregate 0/4 836 Aggregate 4/8 897 Water 185 Cement CEM I 42.5 R 479 Plasticizer 3.48 W/C ratio 0.39 Experimental Setup An experimental loading test were performed at the 33rd day after the casting on all the specimens.
The reinforced concrete samples (RC 1-3) provided significantly higher load-bearing capacity compared to the plain concrete samples.

The green bodies were sintered in air under 2 different regimes: one-step sintering at 800 °C and two-step sintering at 800-700 °C (Fig. 1).
Fig. 1.
The absorption bands around 1100 cm-1 can be attributed to the deformation vibrations of Ti-OH bonds.
References [1] T.
Acta 280/281 (1996) 479–490

Fig. 1 shows a picture of the model.
Table 1: Specifications of the scale model ship Item Description Length 0.78m Width 0.19m Mass 9.2 Kg Propelling source DC motor Endurance 1.2 hours Maximum speed 0.7 m/s Fig. 1.
(1) In this problem we have two inputs, δz (k) and ψ(k-5), and one output ψ(k)
References [1] Wang Meng, Li Hong Sheng, Miao Qing ans Bian Guang Rong.
Archives of Control Sciences, Vol. 24, No. 4, p.p.: 479–497. 2014

Salinas-Delgado2e 1 Cinvestav-Unidad Saltillo, Carr.
Results and discussion Fig. 1 shows the surface of the gentamicin-containg ceramics before and after 21 days of immersion in SBF.
Fig. 1.
References [1] M.
Mater Med 10, 475-479