Search results

Micromechanical Damage Constitutive Model of Leached Concrete Chunxiang Qian1,2,a, Bei Huang1,2,b , Zhihai He3,c,* 1School of materials Science and Engineering, Southeast University，Nanjing 211189, China 2Jiangsu Key Lab on Civil Engineering Materials, Nanjing 211189, China 3College of Civil Engineering, Shaoxing University, Shaoxing 312000, China aemail: cxqian@seu.edu.cn, bemail: hb031020@163.com, cemail:zhihaihe19811020@126.com Keywords: leaching; concrete; constitutive model; mechanical; stress-strain relation Abstract: This paper deal with concrete behavior under chemical and mechanical degradation.
Experimental Descriptions 2.1 Materials and Samples In our experiment, there were two kinds of samples: concrete and paste.
A mechanical 300 KN material test system (MTS) was used to carry out stress-strain curve measurement under uniaxial loading.
Fig.2 Loading test setup 2.4 Analysis Methods The pH value in the pore solution of cementitious materials in higher than 12.5, creating a very basic environment.
Heukamp: submitted to International Journal of Solids and Structures (2001) [3] J.J.

The presented study follows the research focused on strengthening of railway subsoils using FGRC [7, 8].Materials and Samples The samples were made of Portland cement CEM I 42.5 R produced in Radotín and finely ground recycled concrete (FGRC), prepared from old railway sleepers.
Matias et al., Mechanical properties of concrete produced with recycled coarse aggregates - Influence of the use of superplasticizers, Construction and Building Materials 44 (2013) 101-109
Barbudo et al., Influence of water-reducing admixtures on the mechanical performance of recycled concrete, Journal of Cleaner Production 59 (2013) 93-98
Lidmila et al., Mechanical properties of recycled binder/micro-filler cement-based material, Advanced Materials Research 1054 (2014) 234-237
,Utilization of Recycled Fine-ground Concrete from Railway Sleepers for Production of Cement-Based Binder, Applied Mechanics and Materials 486 (2014) 323-326

Zhang etal: Journal of Material Processing technology Vol. 6118 (2002) pp. 1-4
Zhang: Key Engineering Materials Vol. 315 (2006) pp. 607-611
Zhou, S.Huang, X.Ji, etal: Key Engineering Materials Vols. 375-376 (2008) pp. 57-61
Demma, et al: Advanced Materials & Processes Vol. 161 (2003) pp.65-71
Zhao: Material mechanics (Harbin Institute of Technology Press, China 1992)

First, the old materials used one hundred or more years ago are poorly known today, if at all.
An experimental campaign was carried out in order to find the elastic parameters and strengths for individual materials (clay unit and mortar).
Materials and Structures, DOI 10.1617/s11527-009-9492-0
European Journal of Mechanics A-solids, 17, 285-303
PhD thesis, Université des Sciences et Techniques de Lille, France.

In IOP Conference Series: Materials Science and Engineering (Vol. 523, No. 1, p. 012078).
In IOP Conference Series: Materials Science and Engineering (Vol. 523, No. 1, p. 012080).
Journal of Cleaner Production, 107, pp.557-567
Construction and Building Materials, 174, pp.713-729
In IOP conference series: materials science and engineering (Vol. 739, No. 1, p. 012035).

Ismat Shah2,3 c 1Egyptian Petroleum Research Institute (EPRI), Nasr City 11727, Cairo, Egypt. 2Department of Materials Science and Engineering, University of Delaware, Newark, DE 19716, USA 3Department of Physics and Astronomy, University of Delaware, Newark, DE 19716, USA asawsanhassan2003@yahoo.com b. emre@udel.edu c.
Chlorobenzenes and other halo-aromatics are widely used as raw materials for pesticide manufacturing and have a variety of other uses in chemical syntheses and other applications.
Bahramian,High transparent sol-gel derived nanostructured TiO2 thin film, Materials Letters, 62 (2008) 361-364
RangaRao, V.Dutta, Low-temperature synthesis of TiO2 nanoparticles and preparation of TiO2 thin films by spray deposition, Solar Energy Materials and Solar Cells.9 (2007) 1075-1080
[45] U.Diebold, the surface science of TiO2, Surface Science Reports 48 (2003) 53-229

Microstructure and Microwave Absorption Characteristics of BaTiO3-CoFe2O4 Composites Yuda Bakti Zainal1,2,a, Dedi3,b and Azwar Manaf1,c* 1Postgraduate Program of Materials Science, Faculty of Mathematics and Natural Sciences, Universitas Indonesia, Jl.
A few to mention, ferrite-based magnetic materials: Fe-35Co/Fe3O4 composite prepared by solvothermal method.
The two mentioned types of magnetic and dielectric materials have been used as absorbing materials for electromagnetic waves.
Such three physical properties are needed by materials capable of absorbing the electromagnetic waves.
Series: Materials Science and Engineering. 292 (2018) 012062

Pawińskiego 5B, 02-106 Warsaw, Poland 2Faculty of Materials Science and Engineering, Warsaw University of Technology, Woloska 141., 02-507 Warsaw, Poland;: a* dkukla@ippt.gov.pl, brsitek@inmat.pw.edu.pl Keywords: super nickel alloy, alumina layer, fatigue damage Abstract.
The coatings increase the creep strength and also the local thermal stress in the near-surface areas due to the differing thermal expansion of particular material layers.
Introduction The extreme operating conditions of modern aircraft engine turbines require the application of heat-resistant and high-temperature materials.
The material most frequently used as the top coat is the zirconium oxide stabilised with yttrium oxide - ZrO2+Y2O3 [4,5].
The influence of oxides on the performance of advanced gas turbines, Journal of the European Ceramic Society 28 (2008) 1405-1419

Kim: Materials science and engineering, A 402, p. 170–176. (2005)
Zhang: Journal of materials processing technologgy, 137, p. 195-200. (2003)
Steiberg: Materials science and engineering, A286,p.18-29. (2000)
Carr: Materials science and engineerin, A.236, p. 370–381. (2002)
Xia: Materials Science and Engineering, A283, p. 70–75, (2000)

Shape Memory Effect in New Ti-Nb-Ta Alloy Alaa Mahmoud Keshtta 1, a and Mohamed Abdel-Hady Gepreel 1,b 1 Department of Materials Science and Engineering, Egypt-Japan University of Science and Technology (E-JUST), Alexandria, 21934, Egypt.
Materials Science and Engineering: A(2006) 438: pp. 18-24
Materials Science and Engineering: A (1998) 243(1): pp. 244-249
Materials Science and Engineering: C (2005) 25(3): p. 363-369
Materials Transactions. 45(7): pp. 2443-2448