Search results

Improvement in the Sensitivity of the Response of Diamond Thin Films to X-ray Xiaoming Liao, Junguo Ran* , Li Gou, Jin Zhang, Baohui Su and Jiangli Lin Department of inorganic materials, Sichuan University, Chengdu 610065, China Keywords: Diamond thin films, Radiation dosimeter, Response to X-ray, Sensitivity Abstract.
Advances in the preparation of diamond by CVD technology have resulted in improvement in the quality and availability of material suitable for radiation dosimetry.
Experimental Materials and Procedures Diamond thin films were prepared on (100) p-type Si substrates, which were polished with diamond powders to induce nucleation, by a bell jar-type MWPCVD deposition technique.
Acknowledgements This work was supported by the National Natural Science Foundation of China (No. 10275046).
Gou: Journal of Sichuan University (Engineering Science Edition) Vol. 36(4) (2004), pp. 57

Materials and methods Materials Beef flavor was bought from the super market.
Meat Science.
Journal of Clinical and Experimental Medicine (In Chinese).
Meat Science.
Food Science (In Chinese).

., v≥25m/s, the use of tough matrix materials may result in more laminate tensile and flexural strength reduction than that of brittle matrix materials.
The nanoparticles SiO2 (Nanostructured & Amorphous Materials, Inc.
T.Custis: Composites Science and Technology Vol.23 (1985), p.221
Sun: Journal of Composite Materials Vol.19 (1985), p.56
Friedrich: Composites Science and Technology Vol. 65 (2005), p. 635

The semi-solid material was solidified in the mold and preliminary microstructural characterization was performed.
ACKNOWLEDGMENTS The authors acknowledge the financial support from National Council for Science and Technology (CONACyT) and SIP-IPN.
REFERENCES [1] Kotadia, H.R., Hari, B.N., Zhang, H., Arumuganathar, S., Fan, Z., Solidification Behavior of Intensively Sheared Hypoeutectic Al-Si Alloy Liquid, The Minerals, Metals & Materials Society and ASM International (2010); Metallurgical and Materials Transactions A, DOI:10.1007/s11661-010-516-8
[3] Rosso, M., Thixocasting and rheocasting technologies, improvements going on, Journal on Achievements in Materials and Manufacturing Engineering, Vol. 54, 1, (2012), pp 113-114
[6] Figueredo, K., Flemings, M.C., Viscosity of semi-solid A357 alloy in the transient high shear rate regime, Metallurgical Science and Technology (2000); Vol. 18 (2), pp 32-36

In the automotive industry this higher strength enables lightweight, fuel-efficient designs which are nevertheless safer than those using conventional materials.
Science 84 (2014) 339-349 [2] S.M.T.
Journal for Numerical Methods in Engineering 79, issue 11 (2009) 1309-1331 [5] P.
Science 46 (20??)
Kouznetsova, Computational homogenization for the multi-scale analysis of multi-phase materials, PhD.

It effects the friction level and material pick-up behaviour of cutting tool upon sliding with workpiece material [5].
Experiment Material and Method.
Dowling, Journal of Materials Processing Technology 155-156 (2004) 1861-1866
Clemens, Progress in Materials Science 51 (2006) 1032-1114
Vleck, Material Chemistry and Physics 54 (1998) 116-122

Rapid prototyping using robot is made with metallic [11] and non metallic [10,12] materials.
Advanced Materials Research, vol. 463-464, (2012), pp. 1643-1646 [4] H.
Mikolajczyk, Robot-turner, Advanced Materials Research, vol. 463-464, (2012), pp. 1682-1685 [7] T.
Mikolajczyk, Robot application to surface finishing, Journal of Polish CIMAC, vol. 5, nr 3, (2010), pp. 107-112 [10] J.
Advanced Materials Research, vol. 463-464 (2012), pp. 708-711 [16] T.

Kim, "Continuous Casting and Rolling for Aluminum Alloy Wire and Rod", Materials Science Forum, 638-642(2010)255-260
Jabłoński, Effect of Iron Addition to Aluminium on the Structure and Properties of Wires Used for Electrical Purposes, Materials Science Forum, 690(2011)459-462
Gold, Solidification Conditions and Microstructure in Continuously Cast Aluminum 　 JOURNAL OF METALS　April 1982, Volume 34(1982)28–34
Miyake, Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods: Key Engineering Materials, Vol. 805(2019), p. 31-36 [10] T.
Miyake, Fabrication of Aluminum Alloy Rods Using a Single Wheel Caster with Rotating Side Dam Plates and Pool-Less Pouring: Key Engineering Materials, Vol. 792(2018), p. 35-40.

Adnan Tekin High Technological Ceramics & Composites Research Center, Istanbul, Turkey 2 Gebze Institute of Technology, Department of Physics, Gebze, Kocaeli, Turkey 3 Gebze Institute of Technology, Department of Materials Science & Engineering, Electronic Materials Laboratory, Gebze, Kocaeli, Turkey Keywords: thin films, functionally graded coatings, diamond-like carbon, SIMS Abstract.
Experimental Studies A high-speed steel (HSS - Thyssen DIN 13343) was used as a substrate material in our experiments.
From Fig. 2 (b), the main constituent of the HSS substrate material, Fe, is located at the center (right hand side of the figure).
Grill: IBM Journal of Research and Development, Vol. 43 (1999), p. 147 [2] O.H.
Felix: Materials Science and Engineering A, Vol.

Correlations between coating components and mechanical properties of weld deposited metal Gongge Meng1, a, Jijun Chu2,b, Jingyue Luan2,c , Yongsheng Chen1,d 1School of Material Science & Engineering, Harbin University of Science and Technology, Harbin 150040, China; 2Harbin Welding Institute, China Academy of Machinery Science and Technology, Harbin 150080, China; amenggongge@126.com, bcjj28@tom.com, cala_216@163.com, dchengyongsheng111@126.com Keywords: basic electrode; coating components; mechanical properties; deposited metal; uniform design Abstract.
The mechanical properties of metal materials depend on the microstructure, and the microstructure is closely related to the chemical compositions of materials.
(in Chinese) [6] Yuelan Xu, Angjun Hu, Kehong Wang, et al: Ordnance material science and engineering Vol. 27(2004), p. 30-33.
(in Chinese) [8] Youshe Sun, Yimin Tu, Lunchao You: Development and Application of Materials Vol. 17 (2002), p. 8-10.
Majumdar: Journal of Materials Processing Technology Vol. 171(2006), p. 223–231 [10] E.S.