Search results

Deep understanding of the physical properties of the materials under the influence of radiation is vital for effective design of dosimeter devices [3].
Numerous efforts are devoted to investigate the influence of radiation onto the properties of metal oxide materials [4].
However, nature of thin films could be amorphous or polycrystalline at its best, depending on the materials used and the method of preparation [4, 11-13].
SiO films are usually dielectric and are widely used in microelectronics industry as capacitor materials.
Atanassova et al: Microelectronics Journal Vol 32 (2001), p. 553

For the basis of the NASICON structure, researchers have substituted other elements to replace Zr, P or Si., the other research creates replacement materials to produce divalent and trivalent ions, such as Al3+ or Mg2+ [9].
The raw materials were ball-milled for 2 hours, dried at 80°C for 12 hours, then calcined in air at 1125°C for 12h with heating rate of 2°C.min-1.
Bhatnagar, Preparation, Structure and Conductivity of Sn Modified NASICON Material, J.
[15] Bingxing Xie, Danyu Jiang, Jian Wu, Tao Feng, Jinfeng Xia, Hongqiang Nian, Effect Of Substituting Ce For Zr On The Electrical Properties Of Nasicon Materials, Journal of Physics and Chemistry of Solids 88 (2016) 104-108
Setyawan, The Effects of the Addition of Silica Mol Fraction (x= 1.5; 2; 2.5) as a Solid Electrolyte on Ion Conductivity of NASICON (Na1-xZr2SixP3-xO12) Using Solid-State Method, IOP Conference Series: Materials Science and Engineering 202 (1), 012083

Materials and Methods 2.1 Materials and their properties The paving blocks were made using waste materials which include plastic bottles and C&D waste.
The use of only coarse aggregate resulted in significant voids within the mix which ultimately caused poor binding of the materials.
Materials 14, no. 21 (2021): 6605. https://doi.org/10.3390/ma14216605 [25] Balasubramanian, G., D.
Kaith, Composite materials based on recycled polyethylene terephthalate and their properties–A comprehensive review, Compos.
Ispal, and SJ Matlan, Development of Paver Block Containing Recycled Plastic, In IOP Conference Series: Materials Science and Engineering, 1144 (2021) 012094. https://doi.org/10.1088/1757-899X/1144/1/012094 [43] T.

Materials and Methods Isolation, culture and characterization of hUCMSCs.
The isolated hUCMSCs displayed the potential to differentiate along adipogenic and osteogenic lineages after treatment with the respective differentiation protocols described in Materials and Methods (Fig. 3).
First, synthetic matrix materials with the same crosslinking degrees can have distinct modulus due to lack of unified effective representation and measuring methods.
Lin, Crosslinked chitosan: Its physical properties and the effects of matrix stiffness on chondrocyte cell morphology and proliferation, Journal of Biomedical Materials Research Part A. 75A(2005) 742-753
Boyan, Integrin alpha(5) controls osteoblastic proliferation and differentiation responses to titanium substrates presenting different roughness characteristics in a roughness independent manner, Journal of Biomedical Materials Research Part A. 80A (2007) 700-710

Full characterization of this material is providing some information on PANI behavior due to pH and concentration in the prepared precursor.
These three unique chemical states make PANI a preferred polymeric material by researchers.
Dharmadasa, Development of polyaniline using electrochemical technique for plugging pinholes in cadmium sulfide/cadmium telluride solar cells, Journal of Electronic Materials 43(11) (2014) 4003-4010
Giolando, Solar Energy Materials & Solar Cells Pinhole treatment of a CdTe photovoltaic device by electrochemical polymerization technique, Sol.
Patil, Applied Surface Science Effect of pH on the properties of chemical bath deposited polyaniline thin film, Appl.

.% FFA, for used as a raw material to produce biodiesel in the second-step transesterification process.
Furthermore, there are few researches towards the study on the POME as a raw material for produce the biodiesel using heterogeneous acid catalyst of Amberlyst-15.
Materials and Methods Materials.
Acknowledgments This research was supported by National Science, Research and Innovation Fund (NSRF) and Prince of Songkla University (Grant No ENG6505020S).
Journal of Environmental Chemical Engineering Vol. 8 (2020), p. 103538

Introduction The newest technologies together with materials science created a new material group called intelligent materials.
It is a fully reversible transformation and exactly this unique transformation allows SMA materials to revert to their original shape [8].
A tangible effect of using SMA materials is a considerable simplification of the presently used constructions which entails obvious economic benefits.
Along with an increase in the volume of production and decrease in the costs of production, SMA materials become increasingly available on the consumer market [7].
Mechatronic Systems and Materials III /Switzerland: Trans Tech Publications, cop. (2009) [13] K.K.

Modified phenolic resins based on hyperbranched polysiloxane with improved thermal stability and flame retardancy Chenglong Gu, Aijuan Gu*, Guozheng Liang, Li Yuan Jiangsu Key Laboratory of Advanced Functional Polymer Design and Application Department of Materials Science and Engineering College of Chemistry, Chemical Engineering and Materials Science Soochow University, Suzhou 215123, China guchenglong@126.com Keywords: phenolic resin; hybranched phenyl polysiloxane; thermal property; flame retardancy.
What’s more, nowadays certain materials, such as melamine, through adding phenolic resin, can form broad-spectrum moulding compounds to use for applications in electrical equipment as cases, connectors, clamps, etc [7].
Experimental Materials.
Munoz JC, Ku H, Cardona F, Rogers D(2008)Journal of Material Processing Technology 202:486-492
Yang G，Tang C L．Synthesis of the phenol resin modified with an aniline derivative[J]．Insulating Materials，2003，36(2)：l-3 [18].

The residual stress sensitivity determines the influence of residual stress on the materials strength and resistance against fatigue; it increases with tensile strength (Figure 1, a).
Figure 3: Stress strain diagram for investigated materials Specimens were prepared by turning according to [12].
The accuracy and applicability of the presented method, mainly depends on the materials’ residual stress sensitivity, which increases with the ultimate strength.
Further research will be carried out analyzing literature results to identify coefficients for different materials such as AISI 4140.
International Journal of Fatigue, 30, pp. 2050-2055 (2008)

Materials Science Forum Vols. *** (2004) pp.697-701 online at http://scientific.net  2004 Trans Tech Publications, Switzerland A Monitoring System of Drill Wear States Using A Hybrid Neural Network V.
Although there were many works done in on-line tool wear monitoring, in most instances the networks have been trained Advances in Materials Manufacturing Science and Technology 698 using only a few cutting conditions where a range of cutting conditions would have been more appropriate in practice.
Advances in Materials Manufacturing Science and Technology 700 An average flank wear land of 0.3 mm or a maximum flank wear land of 0.6 mm is the criteria to define effective tool-life.
Misclassification cases of Materials Science Forum Vols. *** 701 training data have also occurred in the same way as that of testing data.
Anantharaman: Journal of Engineering for Industy Vol. 116 (1994), p. 392 [4] S.C.