Search results

Improved low Cr steel L Pigliacampo et al. developed the optimization of low carbon steel 3Cr, to fill in the conventional carbon steel and low alloy steel (carbon and low alloy steels, CLASs) and corrosion resistant alloy steel (corrosion resistant alloys, CRAs), the gap between this kind of material than the CLASs has a higher corrosion resistance, with enough mechanical properties at the same time, so low carbon 3Cr optimization will be the choice of appropriate completion homework.
Nasr-El-Din, A.S.
Al- Khuraidah, etc.

Planes et al. [13], on the other hand, suggested that fillers with a large interface influence degradation by trapping radicals that can react with intermediary chemical species implicated in matrix breakdown.
According to Tang et al., [16] formation of the compact charred layer is essential to provide an effective shield against mass and heat transfer.
El-Nemr, Effect of different curing systems on the mechanical and physico-chemical properties of acrylonitrile butadiene rubber vulcanizates, Mater.

., El-Sehily B.M..
[6] Miller E.E., Sutton M.A., Deng X., et al.
Experimental and Predicted Crack Paths for Al-2024-T351 Under Mixed-Mode I/II Fatigue.

The validation of the AEM numerical model has been made simulating in the ELS® computer software an experimental test performed by Yi et al. [13] on a planar RC frame.
A time removal of tr = 5 ms is used, and similar with Sasani et al. [18], Thai and Lin [5], the damping ratio is set to ξ = 5%.
El-Fouly and H.

Hiratsuka has investigated dry sliding friction and wear in vacuum and oxygen of Al, Ni and Cu.
The materials studied were a CuZn brass alloy and steel AISI 1045 with the following chemical composition in weight percent, respectively: for the pin 64% Cu, 0.25% Si, 0.11% Al, 0.21% Fe and the balance Zn; for steel disc Fe + 0.45% to 0.51% C, 0.5% Mn, Si < 0.1, P < 0.035% .
[3] El Mansori M, Zaidi H, Kadiri EK, Paulmier D.

Al-Shareeda3,c, Khalid Asaad Hashim3,d, Nurfarhana Mohamad Sapiee2,e, Hamzah Hidi Qasm4,5,f, Alaa Ibrahim1,g, Nawar Hayder Tawfeeq4,h, Muhammad N.
Saeed et al., "IoT health monitoring system for preventing and controlling risk in confined space using microcontrollers," Int.
Al-Jadiri, "Door lock system based on internet of things and Bluetooth by using Raspberry Pi," Bulletin of Electrical Engineering and Informatics, vol. 12, no. 5, pp. 2753-2762, 2023
El Gannour, N.
Hamzah et al., "Advancing the measurement speed and accuracy of conventional BOTDA fiber sensor systems via SoC data acquisition," Optical Fiber Technology, vol. 84, p. 103712, 2024.

Tsakiridis et al. [19] used RM as a raw material to produce clinker of Portland cement.
In report of Do and Nguyen [15] and Nguyen et al. [30], RM contains quartz (SiO2), hematite (Fe2O3), gibbsite (Al(OH)3), goethite (α-FeOOH), lepidocrokite (γ-FeOOH) and other clay minerals in its minerals compositions.
There have been several investigations using RM as raw meal for the production of clinker cement known as studies of Singh et al. [17, 18], Tsakiridis et al [19], Pontikes and Angelopoulos [21], and Zhang et al. [23].
Al-Dhamri, K.
El-Korchi, G. 

Yung et al. used carbon nanotubes (CNTs) as a filler to produce basalt flake epoxy resin (CNT-BF/EP) coating.
Huang et al enhanced tribological properties of epoxy coating by blending it with different ratios of basalt fiber.
As shown in Fig. 1 (XRD pattern andesine), after crushing and milling andesite basalt rock into fine powder it is found that it composed of a dominant mineral of plagioclase mineral series ((Na,Ca)Al(Si,Al)Si2O8).
Moreover, another mineral from the plagioclase series known as labradorite ((Ca,Na)Al(Al,Si)Si2O8), which is richer in Ca than andesine.
El-Sabbagh, and H.

Ammonia leaching - pressurized hydrogen reduction method of electroplating sludge recycling copper and nickel.Environmental Science and Technology, 2010, 33 (6E): 135-137, 140 [6] F Veglioa, R Quaresimaa, P Fornarib, et al.
Recovery of valuable m et als f rom elect ronic and galvani c indust rial wast es by l eachin g and el ect row inning.
DE MELLO NT, MENEZES DUARTE MM, et al.

[4]Foster I, Kesselman, Nick J, et al.
[5] Cardorso J,Miller J,Sheth A,et al.
El-Hawary, “Hybrid particle swarm opti-mization approach for solving the discrete OPF problem considering the valve loading effects,” IEEE Transactions on Power Systems, vol. 22, No. 4, 2007, pp.2030-2038