Search results

Daria et al. 2020 confirmed that geotextiles made of natural fibers will be widely used in environmental engineering in the years to come [5].
Assumptions: The usual supply perimeters are located in several Moroccan rural communes: Bouchfâa, Smiâa, Ait Zeghrouchen, and in Rebat El Khair.

To our knowledge, only Chen et al. [7] reported the EC/BA/MMA Hybrid Latexes were prepared by batch emulsion polymerization with 6.6wt% toluene and 6.7 wt% hexadecane.
El-Aasser: Macromolecules, Vol. 36 (2003), p. 5573 [13] M.A.

Al-Hazmi: The Second International Conference on Modeling Simulation, and Applied Optimaization ICMSA2007, (Abu Dhabi, March, 2007) [8] X.
Kang, E.L.

They also developed three critical and still living techniques for CIS-based thin-film PV technology; The first was to apply the ZnO:2wt%Al (AZO) window by sputtering techniques, the second was to put the intrinsic (high resistivity) ZnO layer between AZO window and CdS buffer to reinforce the surface coverage of absorber deposited with their CBD-CdS buffer and the third was to alloy gallium (Ga) into the CuInSe2 absorber to form a Cu(In,Ga)Se2 (CIGS) absorber.
Therefore, mapping techniques like EL and PL mapping and LBIC have been employed more as simple and quick characterization techniques for large area [9, 10].

According to the article 5.1.2 in the Code, the EL CENTRO earthquake wave record is adopted as the horizontal seismic wave input.
Wang, A.L.

These were determined through a direct process consisting on digital images treatment from micrographs obtained by optical microscopy following the protocol referred by Fidelis et al, [15]; the images processing consisted of a binarization of the micrographs to black and white images, to subsequently make the pixel counting corresponding to the occupied areas by fibers and subsequently those data were converted to the area units used in the study (mm2), all the process was performed using Fiji, a free specialized digital image processing software.
Tapia Pazmiño, “Estudio de la Adherencia de un Sistema Compuesto FRCM Sostenibles para el Reforzamiento de Elementos de Hormigón Armado,” 2016

Yang et al. [12], who investigated CGHAZ of HSLA steel, suggested that higher heat input may increase granular bainite and M-A phases.
Table 2 Mechanical properties of parent metal SM570-TMC and filler metal E81-Ni1 Material TS (N/mm2) YS (N/mm2) El (%) Impact value (J) SM570-TMC 590 488 38 201 (at -20 °C) E81-Ni1 605 525 27 120 (at -40 °C) Metallographic Examination The metallographic specimens were extracted from welded samples of LNi1 and HNi1 for microstructural analysis.

A study done by While, Ashour et al found that the thermal conductivity for earth plaster reinforced with straw fibres decreased with increasing fibre content and increased with increasing sand content [4].
El-Kassas and A.

However, according to Miyaji et al. 2005 [11] the presence of zinc reduces the crystalline disorder on the carbonated apatite, which results in crystal with less defects and more soluble.
Feki, H.El Feki, Biologic Response to Carbonated Hydroxyapatite Associated with Orthopedic Device: Experimental Study in a Rabbit Model, Korean J Pathol. 46 (2012) 48-54

Almeida Paz,2,c Baltazar de Castro,1,d and Luís Cunha-Silva1,e 1REQUIMTE & Department of Chemistry and Biochemistry, Faculty of Sciences, University of Porto, 4169-007 Porto, Portugal 2CICECO & Department of Chemistry, University of Aveiro, 3810-193 Aveiro, Portugal aandredbarbosa@gmail.com, bsbalula@fc.up.pt, cfilipe.paz@ua.pt, dbcastro@fc.up.pt, el.cunha.silva@fc.up.pt (corresponding author) Keywords: Porous MOFs; Microwave assisted synthesis; oxidation; heterogeneous catalysis.
Synthesis of MIL-101(Cr). hydrothermal method: MIL-101(Cr) was prepared by the adaptation of the original method reported by Férey et al.[17].