Search results

According to Guo et al., in, Al–Si–Fe–Mg alloys hot rolling was found to break down eutectic phases and redistribute them more uniformly, leading to refined particles [45].
[21] Alateyah AI, Alawad MO, Aljohani TA, El-Garaihy WH.
Effect of process parameters on porosity defects in Al-Si alloy hot rolling.
Study on Bulk Texture and Mechanical Properties of As-Extruded Wide Mg-Al-Zn Alloy Sheets with Different Al Addition.
[58] Noradila AL, Sajuri Z, Syarif J, Miyashita Y, Mutoh Y.

Studied the dynamic behaviors of photo-induced insulator-metal phase transition in vanadium oxide thin films with different oxygen stoichiometry, Liu at el[46] found that the phase transition of VO2 was very sensitive to oxygen stoichiometry also.
Pan, et al.
Ko, et al.
Oh, et al.
Ko, et al.

Equilibrium modeling and experimental work on fixed-bed gasification has been reported by a number of researchers such as Umeki et al. [8], Adam et al. [11], Schuster et al. [4], Sheth and Babu [12], Zainal et al. [3], Sharma [13], Puig-Arnavat et al. [14], Jarungthammachote and Dutta [15], but not as widely reported as the research published on fluidized bed gasification.
Equilibrium and kinetic predictions were compared by Dupont et al. [21] and the conclusion was that steam reforming of methane is far from equilibrium under the operating conditions of interest for biomass gasifiers and thus the reaction is kinetically limited.
In addition, the optimized steam gasification conditions (temperature and steam flow rate) in this study are in agreement with the experimentally determined values for steam gasification of wood by Franco et al. [9].
[19] E.L.

Model Validation We compared the model with CDM, which is modeled by Huang at el. and with outfield diffusion experiments.
Progress in Safety Science and Technology Ⅵ, 10(2006),p. 1362-1365 [3] Huang S.X., Liu P., Chen H.P., et al.
Acta Scientiarum Naturalium Universitatis Pekinensis, (2010a),p. 35-38 [4] Zhang L.J., Hu F., Li L., et al.
J Korea Air Pollution Research Association, (1995),p. 145-152 [9] Huang S.X., Liu F. et al.
CCCA 2011, Hong Kong, China, IEEE, 02(2011),p. 301-305 [12] Tong H, Andrew Walton, et al.

Sedghi et al.’s method [15].
Feng et al. [19] have also reported this phenomenon.
Yahya et al., “A review of integrated photocatalyst adsorbents for wastewater treatment,” J.
Yahya et al., “PT SC,” Biochem.
Abd El-latif, A.

These results are found to be in good agreement with those obtained by Gu et al. [5], Alqahtani et al. [7] and Choi et al. [15].
These findings are in agreement with those reported by Alqahtani et al. [7] and Choi et al. [15].
This corroborates the results obtained by Benosman et al. [29] and Zuccheratte et al. [17].
These results are in good agreement with those obtained by Saikia et al. [4], Alqahtani et al. [7], Benosman et al. [8], Marzouk et al. [10], Choi et al. [15], Malešev et al. [26], Hannawi et al. [28, 42], Rahmani et al. [43] and Gupta et al. [12,44].
Panzera, A.L.

Regarding E-devices, Gaonkar et al. [13] demonstrated that the bathtub model is not applicable to predict the hazard rate, promoting instead a “roller-coaster” curve.
As Collins et al. [10] pointed out, the growth can be measured as the rate of defect detection and correction per time interval (Figure 5).
Collins et al. [10] warned that highly accelerating tests are neither structured nor fixed, being instead linked to the experience and intuition of the experts.
Vikki et al., [26] have isolated the main causes determining the failure of tantalum capacitors.
Pecht, «Establishing a Relationship Between Warranty and Reliability,» IEEE Trans. on El., Pack. and Man., vol. 29, n. 3, 2006

Burke et al. reported the successful use of a physiologically acceptable artificial dermis in the treatment of extensive burn injuries with full thickness component on ten patients [2].
All the absorption bands described earlier were still in the range of research conducted by Rose et al. in 2013 [8].
Journal of Applied Materials and Interfaces [9] Peng H, Tan L, Osaki M, Zhan Y, Ijiri K, Tsuchimochi K et al., 2008.
[11] Spielmann H, et. al. 2007.
Vol. 16 No.1 pp.37-44, 2006 [19] El-Sayed YS, 2016.

[6] Frohling S, Schlenk RF, Kayser S, Morhardt M, Benner A, Dohner K, et al.
[11] Gao P , Zhou G Y, Lei D P , Zhang XF, Li L, Xu JW, et al.
[13] El-Khoury V, Breuzard G, Fourré N ,Dufer J.
[17] Shao SL, Sun YY, Li XY, Zhang WW, Fu B, Yun DZ, et al.
[18] Shao SL, Zhang WW, Li XY, Zhang ZZ, Yun DZ, Fu B, et al.

The second type, represented by Kang et al. [4], Massoni et al. [5], and Bennett et al. [6], is an extension of the first type aimed at improving the mechanistic description of hot spot formation with focus on void collapse and frictional sliding.
[2] E.L.
Massoni et al.: Phys.
Bennett et al.: J.
Bdzil et al.: Phys.