Search results

（2）Crack width （4） bj: Crack width (mm);λb: Crack width coefficient; The design temperature difference and steel reinforcement ratio are the main factors influencing the design of crack width and spacing under certain conditions of the concrete and steel material.
Journal of Traffic and Transportation Engineering,2001, 1(2):56-57
Journal of North China Institute of Water Conservancy and Hydroelectric Power, 2012, 33(3):40-43
Shanxi Science & Technology of Communications, 2012,01：1-3 [5] Selezneva, O.
Journal of Transportation Engineering, 2005,131(9):645-652

And also, it is right to forbid throwing household garbage and domestic sewage discharge, and trying to avoid bituminous material, and polluting water by gasoline in the couse of transportation.
[3] Gu xiaoxu,Li zhulong,We wei,Li ting, Research in Construction of Harmonious Color with Circumstance in Highway Architecture[J], Journal of South-to-North Water Transfers and Water Science & Technology,pp.157-160
[7] Li zhulong, Wu hanmin,Zhang jinzhao,New Scientific Research on Qinghai-xizang Highway Engineering[J], Journal of Glaciology and Geocryology,the Fourth International Conference on the Frozen Ground Academic ,2000,pp.48-52
[8] Zhang jinzhao, Li zhulong, Wu hanmin, History of Study on Road Building Techniques in Permafrost Region of Plateau [J], Journal of Glaciology and Geocryology,1999(2),pp.187-191.

This technique is also able to characterize the mechanical behavior of materials using a greatly reduced volume of material.
Williams: International Materials Reviews, 52 (2007) 213 4.
Viswanathan: Journal of Engineering Materials and Technology, 116 (1994) 457 6.
Satpati and S.N.Ojha: Materials Science – Poland, 28 (2010) 335 7.
Husain: Materials Letters, 58 (2004) 2569 9.

Soboyejo a,f,i,* a Department of Materials Science and Engineering, African University of Science and Technology (AUST), Abuja, Federal Capital Territory, Nigeria.
e Department of Materials Science and Engineering, Malete, Kwara State University, Nigeria.
i Princeton Institute for the Science and Technology of Materials (PRISM), 70 Prospect Street, Princeton, NJ 08544, USA.
The materials that were used in the PNIPA gel synthesis were purchased from Sigma Aldrich Co.
Allan, Hoffman, Jorge Heller, An Introduction to Materials in Medicine, 2nd Edition.

You can use additive chromium-type austenitic materials based on steel type 308 and others.
The aforementioned austenitic materials thus fully meet the requirements generally applicable to high-pressure metal hoses.
Table 1 shows the average values of the content of chemical elements in the materials under study from 5 measurements for the corresponding parameters.
The results showed that, in terms of chemical composition, the materials under study meet the requirements of regulatory documents [1, 2].
[14] Ivanov, V., Lavrova, E., Morgay, F. & Semkiv, O (2021) Investigation of the heat-affected zone properties during cladding of power equipment with austenitic materials using control mechanical impacts on the strip electrode, Materials Science Forum, 1038, 100-107. https://doi.org/10.4028/www.scientific.net/MSF.1038.100.

Various sources, including the use of unclean fuels for household purposes in developing countries, emissions from furniture and construction materials, and emissions from microorganisms cause indoor air pollution.
The Journal of the Association of Physicians of India, 71(7), 11–12
SSRN Electronic Journal. 10.2139/ssrn.3952375
International Journal of Scientific & Technology Research 9 (2020): 118-123
The Science of the total environment, 906, 167759. https://doi.org/10.1016/j.scitotenv.2023.167759 [48] Eastham, S.

The major concern about hazardous material infiltration flow underground is concentrated on environment protection, mineral deposit, industry production, etc [2-7].
International Journal of Multiphase Flow, 2002, 28(10): 1659-1686 [5] He Xueqiu, Nie Baisheng.
Journal of Chemical Industry and Engineering, 2005, 56(5): 920-924 [7] C.Y.
International Journal of Multiphase Flow, 2002, 28(10): 1659-1686 [9] Hu M. r., Gu A.Z. , Wang M.
Journal of Southeast University (Natural Science Edition), 2002, 32(2): 237-240 (In Chinese)

Ishai, Engineering mechanics of composite materials, 2nd ed, Oxford University Press, New York, 2006
Chung, Composite materials.
Materials, manufacturing, and design. 3rd ed., CRC Press, Boca Raton, FL, 2008
In: Official Journal of the European Union, 2014
Teti, Machining of Composite Materials, CIRP Annals - Manufacturing Technology 51(2) (2002) 611–634

Tewari Department of Metallurgical and Materials Engineering, Indian Institute of Technology Roorkee, Roorkee-247667, India *email: vnshuklamtech@gmail.com Keywords: High velocity oxy fuel, Microhardness, Microstructure, High temperature oxidation.
The nominal chemical composition of the substrate material is given in Table 1.
Prakash, Mechanical and metallurgical properties of plasma sprayed and laser remelted Ni3Al coatings on boiler tube steels, materials Science and Engineering A, 368 (2004) 149-158
Berndt, Ed., Materials Park, OH, USA: ASM International, (1992) 735-742
Sampath, Eds., Materials Park, OH, USA: ASM International, (1994) 121-126

The increasing diversity of materials and product quality enlarges the application areas of additive manufacturing.
Polymers are the most widely used materials for additive manufacturing.
However, it requires an application orientated choice of the used materials and the set process parameters.
In: British Journal of Sports Medicine 38 (2004) pp. 168-172
[15] Scholz M, Blanchfield J, Bloom L: The use of composite materials in modern orthopaedic medicine and prosthetic devices: A review, Composites Science and Technology 71, pp. 1791-1803, UK, (2011)