Search results

Acknowledgement This project is supported by Scientific&Technical supporting Porject of Gansu Province (No. 1011GKCA007) and Natural Science Foundation of Gansu Province, China (No. 096RJZA099).
Journal of Mathematical Analysis and Applications, 246,28-57 (2000) [3] Walid Abdul-Kader: Capacity improvement of an unreliable production line – an analytical approach, Computer & Operations Research, 33(6), 1695-1712 (2006) [4] Gershwin S B.: An efficient decomposition method for the approximate evaluation of tandem queues with finite storage space and blocking.
Applied Mechanics and Materials, 58-60, 410-416 [9] Terracol C, Davie R.: An Aggregation Technique for Performance Evaluation of Transfer Lines with Unreliable Machines and Finite Buffers, In: IEEE Conf.

Journal Citation (to be inserted by the publisher) Copyright by Trans Tech Publications Two Excited State Structures of Donor-Acceptor Substituted "Proton Sponge" A.
Vistorobskii4 1 Faculty of Chemistry, University of Wrocław, Joliot-Curie 14 St., 50-383 Wrocław, Poland 2 Institute of Physics, Polish Academy of Sciences, Al.
Introduction "Proton sponges" [1, 2], the bi-center nitrogen bases, exhibit a strong basicity and demonstrate an unusual reactivity that organic chemists are exploring for the synthesis of effective new catalysts [3], new photochromic materials and other types of potentially useful compounds [4].

Considering machining efficiency and accuracy, machining gap should be the corresponding gap value when the machining speed reaches its maximum. 1 Introduction Electrochemical machining (ECM) is a kind of material removing machining process, which is based on the principle of electrochemical dissolution of anodic metal in electrolyte.
The typical experimental conditions are as follows: workpiece material is 0Cr18Ni9, concentration of 3NaNO solution is 40g/L, and machining voltage is 5V, so  =3.67e-5 3 cm /(A s) , =0.037 -1 (Ω cm) , RU ≈5V, and =0.4[9].
Science[J], 2000,Vol.289,No.7: pp 98-101
International Journal of Machine Tools & Manufacture[J], 2003,Vol.43:pp 1301-1310

J.Li,Pitting Behavior of aluminum foil during alternating current etching in hydrochloric acid containing sulfate ions,Journal of the electrochemical society,153(2006), C51-C56
[6]Hou Zhaohui,Zeng Jianhuang,Chen Jianjun,Liao Shijun,Ultrasonic-assisted ac etching of aluminum foils for electrolytic capacitor electrodes with enhanced capacitance.Materials Chemistry and Physics,123(2010), 625-628
[9]N.Osawa,K.Fukuoka,Pit nucleation behavior of aluminum foil for electrolytic capacitors during early stage of DC etching,Corrosion Science,42(2000),585-597

Personalized Layer Retrieve for M-learning Resources on User Interest Honghua Xu1,a, Ye Tian2,b, Lin Hu*3,c, Quanbao Gao4,d 1,2,4 Changchun University of Science and Technology, Changchun, Jilin Province, China 3Changchun University of Finance and Economics, Changchun, Jilin Province, China ahonghuax@126.com, btiany@sina.com, chuhu315@126.com, dqbgao@sohu.com Keywords: Personalize, Interest, Ant colony Abstract.
When people search for information materials, they always hope to find out abundant and accurate information, that is, they hope that the result information can satisfy the following two demands: One is that the result information can include all the relative content concerning the query theme.
Journal of Computer assisted learning, vol. 22, pp. 320–325.2004

Fig. 1 Schematic sketch of test setup Fig. 2 Various combinations of anchor Fig. 3 Photograph showing mild steel tank, raining box and lever hatchet Fig. 4 Thin curved plastic shear zone emerging from the bottom of the anchor and then terminating at the ground surface above the level of anchors Material Properties The chosen sand was kept dry and using the sieve analysis, following grain size parameters were obtained: (i) D10 = 0.24 mm, (ii) D30 = 0.42 mm, (iii) D60 = 0.7 mm, (iv) uniformity coefficient, Cu = 3.04, and (v) coefficient of curvature, Cc = 1.096 where D10, D30 and D60 are the sizes corresponding to which 10, 30 and 60% material by mass are respectively smaller than that size.
Earth Science Research, Vol.1, No.1, 27- 56
[9] Niroumand, H. (2010) “Numerical and Experimental Analysis of Pullout Test on Square Horizontal Anchor Plates in Sand”, GEOTROPIKA 2010, 1-3 Dec, Sabah, Malaysia [10] Niroumand, H., and Kassim, Kh.A. (2010) “Analytical and Numerical Studies of Horizontal Anchor Plates in Cohesionless Soils”, Electronic Journal of Geotechnical Engineering (EJGE), Vol. 15, Page 281-292 [11] Niroumand, H., and Kassim, Kh.A. (2010) “Compare of Anchor Systems in Geotechnical Engineering”, MICCE 2010, Makassar, Indonesia, 9-10 March [12] Ovesen, N.

Acknowledgment This work has been funded by the Spanish Ministry of Science and Innovation under the grant of the research project DPI2011-27567-C02-01.
Ahmad, Complex dynamics of slack mooring system under wave and wind excitations, The Open Oceanography Journal (2010)
Workshop on Advanced Smart Materials and Smart Structures Technology, Dalian, China (2011)

Experimental Materials.
O, Malaysian Journal of Microbiology, Vol. 15(2009),P.1-5
Wang: Science China Chemistry, Vol. 54(2011), P.715-723.

Stress-Temperature Phase Diagram of Ni2MnGa and Structural Relations between Its Constituent Phases Takashi Fukuda a, Tomoyuki Terai, Hidefumi Maeda, and Tomoyuki Kakeshita Department of Materials Science and Engineering, Graduate School of Engineering, Osaka University, 2-1, Yamada-oka, Suita, Osaka 565-0871, Japan afukuda@mat.eng.osaka-u.ac.jp Key words: Stress-induced transformation, ferromagnetic shape memory alloy, single crystal, incommensurate structure Abstract.
Physica Journal Special Topics 158 (2008) 87

Effects of nutritional conditions on the Stable Carbon and Nitrogen Isotope of Microalgae WANG Haixia1, a, LIU Yu1,b, LIU Ling1,c, Bao Huiming1,d and LIU Baozhan2,e 1College of Environmental Science and Engineering, Dalian Maritime University, Dalian 116026, P.R.China 2Department of Geology and Geophysics, Louisiana State University, Baton Rouge 7803, U.S.A.
Materials and methods Culture.
Edna, “Carbon isotope signature variability among cultured microalgae: Influence of species, nutrients and growth”, Journal of Experimental Marine Biology and Ecology, vol.372, pp.98-105, 2009