Search results

References [1] Huang-Sung Liu, 2005, “A study on the characterization of high nickel alloy micro-holes using micro-EDM and their applications”, Journal of materials processing technology, 169,418-426
[4] H.T.Lee, T.Y.Tai, 2003, “Relationship between EDM parameters and surface crack formation”, Journal of materials processing Technology, 142, 676-683
Luis, 2003, “A study on the machining parameters optimisation of electrical discharge machining”, Journal of Materials Processing Technology, 143-144, 521-526
Bleys, 2004, “Investigation of material removal mechanisms in EDM of composite ceramic material”, Journal of Materials Processing Technology, 149(1-3), 347-352
[7] R.S.Paeade, Suhas S.Joshi, P.K.Brahmankar, and M.Rahman, 2007, “An investigation of cutting forces and surface damage in high-speed turning of Inconel 718”, Journal of Materials processing technology, 192-193,139-146.

Experimental Study on the Tribological Properties of Water-lubricated Rubber Bearings You-Qiang Wang a and Mei-Shu Wang b Qingdao Technological University, Qingdao, 266033, P.R.China awyq@qtech.edu.cn bwangmeishu123@126.com Keywords: Rubber journal bearing; water lubrication; experimental study; tribological property; friction coefficient.
The outer shell material is 45 steel and the diameter is 90 mm.
Acknowledgements This work was financially supported by the National Natural Science Foundation of P.R.China through contract no.50875137, Natural Science Foundation of Shandong Province Government P.R.China through contract no.Y2007F30 and Taishan Scholar Special Fund of Shandong Province Government.
[5] X.J.Hua, J.X.Wang et al: Journal of Advanced Manufacturing Systems.

Experimental Study on the Lubrication Behaviors of Seawater-lubricated Thordon Bearings You-Qiang Wang a ,Wen-Li Sun b Qingdao Technological University, Qingdao,266033, P.R.China awyq@qtech.edu.cn, bwenliaimama@sina.com Keywords: Thordon journal bearing; seawater lubrication; experimental study; tribological property; friction coefficient.
The outer shell material is 45 steel and the diameter is 90 mm.
Acknowledgements This work was financially supported by the National Natural Science Foundation of P.R.China through contract no.50875137, Natural Science Foundation of Shandong Province Government P.R.China through contract no.Y2007F30 and Taishan Scholar Special Fund of Shandong Province Government.
[5]X.J.Hua, J.X.Wang et al: Journal of Advanced Manufacturing Systems.

Preface PUBLICATION OF POWDER DIFFRACTION RESULTS "times are changing" For a long time scientific results were published in printed form on paper in issues of scientific journals dedicated to the field of science concerned.
This explains the emergence of new electronic journals and electronic versions of the established journals.
All previous EPDIC proceedings have appeared as volumes of the journal Materials Science Forum; both in hard copy and electronically in full text on the web.
Reviewing the eight editions of the EPDIC proceedings, the ratios of the numbers of papers on developments in the methods and techniques of powder diffraction and those on applications of powder diffraction methods to specific classes of materials are found to be 1.0, 0.7, 0.5, 1.0, 0.9, 0.5, 0.7 and, for the current proceedings, 0.7.
All too many papers just increase the entropy of the subject without providing substantial advancement of science.

Concretely, the titanium alloy Ti-6Al-4V and the composites Ti-6Al-4V with 10 vol% (TiB+TiC) particulates were employed as the ground materials respectively.
Chrysanthou: Journal of the European Ceramic Society, Vol. 28 (2008), pp.1697–1713
Mai: Composites Science and Technology, Vol. 68 (2008), pp.583-601
Zhang: Key Engineering Materials, Vol. 351 (2007), pp.201-207
Hung: Journal of Materials Processing Technology, Vol. 123 (2002), pp.13-17.

Rational Provision of Functional Properties of Interference Fit Joints in Case of Assembly with Implementation of Anaerobic Materials I.I.
Horník4,g 1Penza State University, 40, Krasnaya street, Penza, 440026, Russia 2LLC «Stankomashstroy», 9, Titova street, Penza, 9440028, Russia 3Slovak University of Technology in Bratislava, Faculty of Materials Science and Technology, J.
[8] The application of anaerobic materials in assembling fixed joints type shaft – bushing / I.I.
Technological provision of the strength characteristics of pressure joints during assembly with anaerobic materials: dissertation for the degree of candidate of technical sciences: 05.02.08 / Evstifeeva Ekaterina Anatolyevna. - Penza, 2009. - 170 p
Improving the technology of assembly and design of interference fit joints using anaerobic materials / I.I.

Based on this work, the tape casting slurry recipe was recently adapted to other materials aiming at the processing of proton conducting and oxygen ion conducting materials.
One of the current membrane materials is the mixed ionic and electronic conductive material BSCF [8].
Journal of Fuel Cell Science and Technology, 2009. 6(2): p. 021302. 7.
Journal of Membrane Science, Membranes and CO2 Separation, 2010. 359(1-2): p. 149-159. 9.
Journal of Membrane Science (submitted Jan 2011), 2011.

However, these materials suffer from poor mechanical properties.
Experimental Materials and Methods Methods for Creating the Moldings.
In this study, we evaluated the use of bamboo fibers and powder as raw materials and for molding purposes, respectively.
Two evaluations were conducted on the raw materials.
S., Manson, J, -A., E., Gibson, A., G., A model for the consolidation of aligned thermoplastic powder impregnated composites, Journal of Thermoplastic Composite Materials, Vol. 8, (1995), pp. 138-162

Experimental progam Materials.
Materials. 2010, 3(2): 918-942
MATERIALS & DESIGN. 2014, 59: 1-9
KONA Powder and Particle Journal. 2009, 27: 119-129
Journal of Applied Polymer Science. 2013, 129(1): 346-353

Explore for new, high strength to weight ratio materials with better strength and toughness has guided to the improvement of a new age group of materials, while their properties may generate key challenges in machining operations.
Material that can be Machined All conducting metals and alloys Limitations Non conducting materials can’t be machined.
References [1] Che Chung Wang, Biing Hwa Yan, Blind-hole drilling of Al2O3/6061Al composite using rotary electro-discharge machining, Journal of Materials Processing Technology 102 (2000) 90-102
[2] S.Sivasankar, R.Jeyapaul, Performance study of tool materials and optimization of process parameters during EDM on zrb2-sic composite through particle swarm optimization algorithm, International Journal of Engineering Science and Technology, Vol. 5 No.01 January 2013
[3] Balbir Singh, Jatinder Kumar, Sudhir Kumar, Influences of Process Parameters on MRR Improvement in Simple and Powder Mixed EDM of AA6061/10%SiC Composite, Journal of Materials and Manufacturing Processes, December 2014, 303-312