Papers by Author: Didier Chaussende

Abstract: Using 6H SiC wafers including regions with a varying residual stress, the birefringence pattern of almost vertical dislocations is measured and modeled. We show that it is possible to identify the basal plane component of "small" dislocations by a quantitative fit of the birefringence pattern. Combining birefringence and etch pit detection after KOH etching shows that most of the vertical dislocations are of a mixed nature, exhibiting both an edge and a screw component.

Abstract: The 3C-6H polytypic transition in 3C-SiC single crystals is studied by means of diffuse X-ray scattering (DXS) coupled with transmission electron microscopy (TEM). TEM reveals that the partially transformed SiC crystals contain regions of significantly transformed SiC (characterized by a high density of stacking faults) co-existing with regions of pure 3C-SiC. The simulation of the diffuse intensity allows to determine both the volume fraction of transformed material and the transformation level within these regions. It is further shown that the evolution with time and temperature of the transition implies the multiplication and glide of partial dislocations, the kinetics of which are quantified by means of DXS.

Abstract: Besides the seeded sublimation process, which is the current industrial crystal growth process for silicon carbide (SiC), solution growth appears as a possible method for high quality bulk crystals. For a further development of the latter technique, a robust numerical model has been implemented with the aim to give quantitative outcomes in addition to qualitative information. Growth rates have been calculated for three different temperature ranges (1700, 1800 and 1900°C) in pure silicon. The computed values were found to be in good agreement with the experimental ones.

Abstract: We present the results of an optical investigation performed using low temperature photomuminescence and Raman spectroscopy on bulk 3C-SiC samples grown with the Continuous-Feed Physical Vapor Transport technique, using a small diameter neck to filter the defects and improve the as-grown material.

Abstract: This work presents the crystalline quality investigation of 3C-SiC unseeded crystals grown from vapor phase. Samples were polished after different crystallographic planes from crystals grown with or without nitrogen flow. The structural and optical investigation showed that the central part of the samples exhibited a very good crystalline quality. The best samples proved to be the {100} growth sectors where the only defects found were stacking faults with a defect density under 103 cm-1. At the edges, i.e. between two adjacent growth sectors, structural investigation by transmission electron microscopy revealed stacking faults and hexagonal polytype inclusions. The nitrogen doping was found not to have an influence on the crystalline quality.

Abstract: In the present work the defects appearing in layers grown by liquid phase epitaxy on different substrates are compared. The used seeds were (i) 3C-SiC with (111) orientation, grown heteroepitaxially on (0001) 4H-SiC or 6H-SiC substrates by continuous feed physical vapour transport process and the vapour-liquid-solid mechanism, respectively, and (ii) 3C-SiC wafer with (100) orientation from HOYA. The structural and optical investigation showed that (i) on the (111) substrates, due to the appearance of silicon and 6H-SiC inclusions, a layer which consisted of a sequence of long period polytypes was formed. The dominant polytype formed was 21R-SiC, which after successive transformation to 39R- and 57R- SiC led to the formation of 6H-SiC on the top of the layer. (ii) On the (100) substrates, a 3C-SiC layer with comparatively uniform defect density was formed. The main defects were stacking faults and their density was reducing during the process.

Abstract: The influence of nitrogen impurity on the stabilization of 3C-SiC polytype has been studied during vapour-liquid-solid (VLS) growth on 6H-SiC(0001) seed with Si-Ge melt. By changing the partial pressure of N2 during growth, it was found that the proportion of 3C-SiC inside the grown material increases with N2 partial pressure. 6H inclusions are only found for high purity (low N2 content) conditions. The possible interactions proposed to explain this effect are divided in two effects: i) lattice parameter modification and ii) surface induced lateral enlargement variation. A combination of both effects is suspected.

Abstract: Despite outstanding properties, the development of 3C-SiC electronics is still suffering from the lack of bulk 3C-SiC substrates. Up to now, there is no real seed and optimized growth processes for this material. We address in this work the bulk growth of 3C-SiC by a two-step-liquid phase approach. By coupling experiments with global process simulation, we address the problems that must be overcome to consider the solution growth technique as a possible approach for the growth of bulk 3C-SiC.

Abstract: The Continuous Feed-Physical Vapor Transport Technique (CF-PVT) was optimized by considering the heating, thermal insulation and the geometry of growth cavity. The effects of seeds on the surface morphology of the grown layer have been discussed. We successfully grew 3C-SiC bulk with a diameter of 7.0 mm and 3.3 mm in height with a high growth rate of 0.8 mm/h by the CF-PVT technique.

Abstract: We report in this work, the solution growth of heavily p-type doped 3C-SiC and 6H-SiC. Description of the 3C and 6H-SiC crystals in terms of defects and resistivity are presented and discussed with respect to growth conditions such as temperature, Al content in the melt and seed polarity. Crystals and thick layers are investigated by means of TEM, NDIC microscopy and Raman.