Static and Dynamic Analysis of Aluminium Composite in Wing Section Using ANSYS

Abstract:

The cold of this cardboard is to abstraction and analyze the amount accustomed accommodation and weight accumulation of blended aircraft (Aluminium Silicon Carbide) addition with that of Aluminium wing and appropriately access the acceptable aircraft addition of minimum weight accomplished of address a accustomed changeless amount after failure. And also this paper presents a model and a static analysis of the aircraft wing, using the finite element software ANSYS. The geometry was created in CATIA V5 R18 and imported. The static and model analysis are carried out in analysis software ANSYS. The result of from the static analysis refers to the total deformation, equivalent stress, shear stress and shear intensity on the skin of the aircraft wing. The model analysis will be carried out to find out the first six modes of vibrations and the different mode shape in which wing can deform without the application of load. Compared to the conventional Aluminium wing, the hybridized composite wing experience far lower stresses and the aircraft wing weight nearly 40% and 50% lower stress.

• Periodical: Advanced Materials Research (Volumes 984-985)
• Pages: 367-371
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.984-985.367
• Online since: July 2014
• Authors: E.S. Esakkiraj*, S. Anish, V. Anish
• Keywords: Aircraft Wing, Aluminium Composite, Modes of Vibrations, Shear Intensity, Shear Stress, Static Load

References

[1] Eng. bogdancaloian, Eng. dorinlozici, Eng. Radubisca, Stress and Modal Analysis Report for Avert Program, DOI 10. 13111/ 2066-8201. 2009. 1. 1. 6- (2009). 28-32.

[2] Mr. Mayurkymarkevadiya, CFD Analysis of Pressure Coefficient for NACA 4412, IJETT Vol 4 ISSUE 5 – (2013). 2041-(2043).

[3] Md. Shamim Mahmud, Analysis of effectiveness an airfoil with BicamberSurface, ISSN 2049-3444, Vol 3, No 5, ( 2013). 569-577.

[4] Mayurkumarkevadiya, Hemish A. Vaidy, 2D analysis of NACA 4412 airfoil, ISSN 2319-8753, Vol 2, issue 5, ( 2013). 1686-1691.

[5] C. Mohanraj, J. Osanna, Areoeleasticity Consideration in Aerodynamic Adaptation of wing, issn 2319-6734, (2012). 101-109.

[6] Mr. ArvindPrabhakar, CFD Analaysis of static pressure and dynamic pressure for NACA 4412, IJETT, Vol4 issue8( 2013). 32-41.

[7] Mahendraagrawal, Gaurav Saxena, Analysis of wings using airfoil NACA 4412 at different angle of attack, IJMER, Vol3, issue3, ( 2013). 3258-3265.

[8] Douvi C. Eleni, Tsavalos I. Athanasios and Margaris p. Dionissios, Evalution of the turbulences models for the stimulation of the flow over a national advisory committee for aeronautics NACA 0012 airfoil, JMER Vol4(3), pp.100-111, ( 2012)100-111.

DOI: 10.5897/jmer11.074

[9] Dr.R. Rajappan, V. Pugazhenthi, Finite element analysis of aircraft wing using composite structure, IJES, Vol 2, issue2( 2013). 74-80.

[10] Sunanda,M. SivaNayak, Analysis of NACA 2412 for automobile rear spoiler using composite material, IJETAE, Vol3, issue1, (2013). 236-24.