Fatigue Crack Propagation in 5754 Aluminum Alloy under Four-Point Bending

Abstract:

The aluminum 5754 alloy is one of the widely used engineering materials in shipping, rivet making, tread plates and automotive industries. These engineering structures envisage variable loading conditions during their service. In addition to it, it is also experiencing seismic vibrations. Hence, the engineering components made from such aluminum alloy are susceptible to fatigue fracture. In the current study, the prediction of fatigue crack growth (FCG) in 5754 aluminum alloy was made using the exponential function. The beam specimen comes up with a cross-section of 25X25 mm², a span length of 300 mm with a mechanical notch length of 2.70 mm at the centre was subjected to four-point bending (FPB) employing hydraulic INSTRON 8800 tensile testing apparatus. The periodic loading condition deformed the material up to large plastic deformation. The applied load was further down the elasticity of the material. The experimental data provided the relation between crack length (a) to the number of cycles (N) to failure. The response surface methodology (RSM) and modified exponential equation were used to predict the FCG. In RSM, when “stress intensity factor (K)” and “number of the cycle (N)" were considered independent variables, the response (a) was optimum (maximum) as compared to when “stress intensity factor range (del K)” and “fatigue crack growth rate (da/dN)” were considered independent variables. Hence, for designing the aluminum 5754 alloys as engineering structures, it was the number of cycles which provides a safe design as compared to da/dN. The modified exponential equation using an exponential function predicted the FCG for aluminum 5754 alloy in the form of a beam specimen. The anticipated results agreed with experimental data as the prediction ratio was 1.20 and the % deviation was 3.7.

• Periodical: Defect and Diffusion Forum (Volume 430)
• Pages: 55-62
• DOI: https://doi.org/10.4028/p-bZQd89
• Online since: January 2024
• Authors: Mamookho Elizabeth Makhatha, Pawan Kumar*, D.A. Baruwa
• Keywords: Aluminium Alloy, Crack Length, Fatigue, Four Point Bend Test, Stress Intensity

References

[1] Rudawska, A., & Wahab, M. A. (2019). The effect of cataphoretic and powder coatings on the strength and failure modes of EN AW-5754 aluminium alloy adhesive joints. International Journal of Adhesion and Adhesives, 89, 40-50.

DOI: 10.1016/j.ijadhadh.2018.11.005

[2] Hussain, K. (1997). Short fatigue crack behaviour and analytical models: a review. Engineering Fracture Mechanics, 58(4), 327-354.

DOI: 10.1016/s0013-7944(97)00102-1

[3] Beden, S. M., Abdullah, S., & Ariffin, A. K. (2009). Review of fatigue crack propagation models for metallic components. European Journal of Scientific Research, 28(3), 364-397.

[4] Pippan, R., & Hohenwarter, A. (2017). Fatigue crack closure: a review of the physical phenomena. Fatigue & fracture of engineering materials & structures, 40(4), 471-495.

DOI: 10.1111/ffe.12578

[5] Kumar, P., Makhatha, M. E., Sengupta, S., & Dutt, A. K. (2020). Prediction of the propagation of fatigue cracks in part-through cracked pipes with CASCA and FRANC2D. Transactions of the Indian Institute of Metals, 73, 1417-1420.

DOI: 10.1007/s12666-020-01886-z

[6] Kumar, P., Sahu, V. K., Ray, P. K., & Verma, B. B. (2016). Modelling of Fatigue Crack Propagation in Part-Through Cracked Pipes Using Gamma Function. Mechanics, Materials Science & Engineering, 6.

[7] Tran, V. X., Pan, J., & Pan, T. (2008). Fatigue behaviour of aluminum 5754-O and 6111-T4 spot friction welds in lap-shear specimens. International Journal of Fatigue, 30(12), 2175-2190.

DOI: 10.1016/j.ijfatigue.2008.05.025

[8] Chowdhury, S. H., Chen, D. L., Bhole, S. D., Cao, X., & Wanjara, P. (2012). Lap shear strength and fatigue life of friction stir spot welded AZ31 magnesium and 5754 aluminum alloys. Materials Science and Engineering: A, 556, 500-509.

DOI: 10.1016/j.msea.2012.07.019

[9] Qiao, Y., Zhang, H., Zhao, L., & Feng, Q. (2020). Fatigue crack growth properties of AA 5754 aluminum alloy gas tungsten arc welding and friction stir welding joints. Journal of Materials Engineering and Performance, 29, 2113-2124.

DOI: 10.1007/s11665-020-04739-4

[10] Mirza, F. A., Macwan, A., Bhole, S. D., & Chen, D. L. (2016). Microstructure and fatigue properties of ultrasonic spot welded joints of aluminum 5754 alloy. JOM, 68, 1465-1475.

DOI: 10.1007/s11837-015-1796-7

[11] Mohanty, J. R., Verma, B. B., & Ray, P. K. (2009). Prediction of fatigue crack growth and residual life using an exponential model: Part I (constant amplitude loading). International Journal of Fatigue, 31(3), 418-424.

DOI: 10.1016/j.ijfatigue.2008.07.015

[12] Mohanty, J. R., Verma, B. B., & Ray, P. K. (2009). Prediction of fatigue crack growth and residual life using an exponential model: Part II (mode-I overload induced retardation). International Journal of Fatigue, 31(3), 425-432.

DOI: 10.1016/j.ijfatigue.2008.07.018

[13] Kumar, P., Hemendra, P., Ray, P. K., & Verma, B. B. (2016). Calibration of COD Gauge and Determination of Crack Profile for Prediction of Through the Thickness Fatigue Crack Growth in Pipes Using Exponential Function. Mechanics, Materials Science & Engineering, DOI, 10.

[14] Vishwanatha, H. M., Kumar, P., Das, A., Agrawal, A., Kumar, C. S., & Verma, B. B. (2022, September). Prediction of the Propagation of Fatigue Cracks for a Beam Specimen in Four-Point Bending Using CASCA and FRANC2D. In Advances in Multidisciplinary Analysis and Optimization: Proceedings of the 4th National Conference on Multidisciplinary Analysis and Optimization (p.301). Springer.

DOI: 10.1007/978-981-19-3938-9_32

[15] Tarafder, S., Tarafder, M., & Ranganath, V. R. (1994). Compliance crack length relations for the four-point bend specimen. Engineering fracture mechanics, 47(6), 901-907.

DOI: 10.1016/0013-7944(94)90068-x

[16] Anderson, T. L. (2017). Fracture mechanics: fundamentals and applications. CRC press.