Effect of Cooling Rate on the As-Cast Microstructure of a High Strength Steel Produced in a Large Size Ingot

Abstract:

This paper presents an experimental study on the influence of solidification cooling rate on the evolutions of microstructural morphologies of a high strength low alloy steel. To this end, solidification samples (cylindrical form with 10 mm diameter and 120 mm length) were prepared from 30 cm below the ingot/hot-top interface, at the center, of a 40 MT (Metric Ton) ingot. Solidification experiments were carried out by using Gleeble^® 3800 thermo-mechanical simulator. Two solidification cooling rates of 1 and 50°C/s were chosen. For microstructural characterization, samples were prepared by mounting, polishing and etching with 3% Nital solution. Also, an optical microscope was employed for microstructural observations. The obtained results showed that for 1°C/s, the microstructure is composed with dendrites and grains. Here, the grain morphology is the dominant one. In the case of 50°C/s, the dendrites were localized at the sample surface and the grains were present more into the depth of the sample. Moreover, the increase of solidification cooling rate results in finer dendrites. The results are discussed in the framework of solidification mechanisms.

• Periodical: Key Engineering Materials (Volume 1016)
• Pages: 9-14
• DOI: https://doi.org/10.4028/p-WM5xmN
• Online since: June 2025
• Authors: Abdelhalim Loucif*, Davood Shahriari, Kanwal Chadha, Chunping Zhang, Jean Benoit Morin, Mohammad Jahazi
• Keywords: Dendrite, Grain, Morphology, Solidification Cooling Rate, Steel

References

[1] D.M. Stefanescu and R. Ruxanda: Fundamentals of solidification, Book chapter, Metallography and microstructures, ASM International, Vol. 9 (2004), p.1

DOI: 10.31399/asm.hb.v09.a0003724

[2] S. Feng, E. Liotti and P.S. Grant: Materials, Vol. 15, 1319 (2022), p.1

[3] J. Campbell: Complete casting, Handbook, Metals casting processes, metallurgy, techniques and design, Butterworth-Heinemann is an imprint of Elsevier, First edition, (2011)

[4] K. Tamta and D.B. Karunakar: Int. J. Mech. Eng. & Rob. Res., Vol. 1 (2014), p.1

[5] A. Loucif, M. Bitterlin, M. Jahazi, R. Tremblay, J-B Morin and L-P. Lapierre-Boire: Metallogr. Microstruct. Anal., Vol. 7 (2018), p.203

DOI: 10.1007/s13632-018-0434-5

[6] C. Zhang, A. Loucif, M. Jahazi, R. Tremblay and L-P. Lapierre-Boire: Appl. Sci., Vol. 8, 1878 (2018), p.1

[7] A. SenGupta, B. Santillana, S. Sridhar and M. Auinger: Dendrite growth direction measurements: understanding the solute advancement in continuous casting of steel, IOP Conf. Series: Materials Science and Engineering 529, (2019), p.1

DOI: 10.1088/1757-899x/529/1/012065

[8] H. Mehrara, B. Santillana, D.G. Eskin, R. Boom, L. Katgerman and G. Abbel: Modeling of primary dendrite arm spacing variations in thin-slab casting of low carbon and low alloy steels, The 3rd International Conference on Advances in Solidification Processes, IOP Conf. Series: Materials Science and Engineering 27, (2011), p.1

DOI: 10.1088/1757-899x/27/1/012046

[9] F.C. Campbell: Fundamentals of solidification, Phase diagrams-understanding the basics, ASM International, (2012), p.429

[10] M. Torkar, F. Tehovnik, B. Arh, M. Jenko, B. Šarler and Ž. Rajic: Mater. Technol., Vol. 48 (2014), p.537

[11] E.S. Dahle: Grain refinement of high alloyed steel with cerium addition, Master thesis, Norwegian University of Science and Technology, (2011)

[12] A. Loucif, D. Shahriari, K. Chadha, C. Zhang, M. Jahazi, L-P. Lapierre-Boire and R. Tremblay: Mater. Sci. Forum., Vol. 941 (2018), p.15

DOI: 10.4028/www.scientific.net/msf.941.15

[13] C. Zhang , Y. Bao and M. Wang: La Metall. Ital., Vol. 1 (2016), p.37

[14] J. Ma, M. Miou, H. Esaka, K. Morishita and H. Miyahara: ISIJ Int., Vol. 63 (2023), p.1122

[15] Y. Zhang, X. Wang, S. Yang, W. Chen and H. Hou: Materials, Vol. 14 (2021), p.1

[16] M. Bleckmann, J. Gleinig, J. Hufenbach, H. Wendrock, L. Giebeler, J. Zeisig, U. Diekmann, J. Eckert and U. Kühn: J. Alloys Compd, Vol. 634 (2015), p.200

DOI: 10.1016/j.jallcom.2015.02.004

[17] T. Wang: The effects of cooling rate and alloying elements on the solidification behaviour of continuously cast super-austenitic and duplex stainless steels, School of Mechanical, Materials, Mechatronics and Biomedical Engineering, Master of Material Engineering, (2019)