Surface Modification of Pure Magnesium and Magnesium Alloy AZ91 by Friction Stir Processing

Abstract:

In recent years an interest in magnesium and magnesium alloys not only for the automotive industry but also for medical applications was increasing due to the low density and good specific strength. Magnesium alloys show good castability but lower ductility and strength than wrought materials. For this reason, refinement of grains and homogenous distribution of intermetallic phases are needed to improve formability and mechanical properties. On the other hand, the degradation of the material by corrosion is influenced by the grain size and phase distribution. This work investigates the microstructure evolution of pure Mg and magnesium alloy AZ91 by friction stir processing (FSP) technique. FSP experiments are carried out by constant force, optimizing the rotation and feed rate to obtain a homogenous microstructure, free of defects stir zone, good surface finishing and stable conditions during the process. The results show that the grain size is affected by the spindle speed. Increasing the number of passes reduces also the size of the grains and the intermetallic phases in the AZ91 alloy. The overlapping of passes between overlapping ratio 0.5 to 1 determines an uniform depth of the stir zone over a larger surface area.Hardness measurements are performed to evaluate the influence of FSP parameters on the mechanical properties. The degradation rate of the studied FSP Mg alloys is determined by hydrogen evolution in corrosion immersion tests, which depend strongly on the phase distribution and grain size.

• Periodical: Key Engineering Materials (Volumes 651-653)
• Pages: 796-801
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.651-653.796
• Online since: July 2015
• Authors: Andreas Hütter*, Wilfried Huemer, Claudia Ramskogler, Fernando Gustavo Warchomicka, Aymen Lachehab, Rudolf Vallant, Christof Sommitsch
• Keywords: AZ91, Corrosion, Friction Stir Processing, Magnesium

References

[1] B. Mordike, T. Ebert: Magnesium: Properties-applications-potential, Materials Science and Engineering: A, Vol. 302, (2001), 37-45.

[2] M. P. Staiger, A. M. Pietak, J. Huadmai, G. Dias: Magnesium and its alloys as orthopedic biomaterials: A review, Biomaterials 27, (2006), 1728–1734.

DOI: 10.1016/j.biomaterials.2005.10.003

[3] J. Gandra, R. M. Miranda, P. Vilaca: Effect of overlapping direction in multipass friction stir processing, Materials Science and Engineering A, Vol. 528, (2011), 5593-5599.

DOI: 10.1016/j.msea.2011.03.105

[4] A. A. Nia, H. Omidvar, S. H. Nourbakhsh: Effects of overlapping multi-pass friction stir process and process and rapid cooling on the mechanical properties and microstructure of AZ31 magnesium alloy, Materials and Design, Vol. 58, (2014), 298-304.

DOI: 10.1016/j.matdes.2014.01.069

[5] M. Alvaro-Lopez, M. D. Pereda, J. A. del Vallea, M. Fernandez-Lorenzo, M. C. Garcia-Alonso, O. A. Ruano and M. L. Escudero: Corrosion behaviour of AZ31 magnesium alloy with different grain sizes in simulated biological fluids, (2009).

DOI: 10.1016/j.actbio.2009.04.041

[6] M. B. Kannan, W. Dietzel, R. Zettler: In vitro degradation behaviour of a friction stir processed magnesium alloy, J Mater Sci: Mater Med, Vol. 22, (2011), 2397-2399.

DOI: 10.1007/s10856-011-4429-x

[7] M. -C. Zhao, M. Liu, G. Song, A. Atrens: Influence of the β-phase morphology on the corrosion of the Mg alloy AZ91, Corrosion Science, Vol. 50, (2008), 1939-(1940).

DOI: 10.1016/j.corsci.2008.04.010

[8] Datasheet of the material provided by the manufacturer Non Ferrum Metal Powders, (2013).

[9] G. Song, A. Atrens, D. StJohn: An Hydrogen Evolution Method for the Estimation of the Corrosion Rate of Magnesium Alloys, Magnesium Technology 2001, (2001), 256-257.

DOI: 10.1002/9781118805497.ch44

[10] R. Ambat, N. N. Aung, W. Zhou: Evaluation of microstructural effects on corrosion behavior of AZ91D magnesium alloy, Corrosion Science, Vol. 42, (2000), 1439-1450.

DOI: 10.1016/s0010-938x(99)00143-2