Finite Element Simulation of the Cutting Process for Inconel 718 Alloy Using a New Material Constitutive Model

Xiang Yu Wang; Chuan Zhen Huang; Jun Wang; Bin Zou; Guo Liang Liu; Han Lian Liu

doi:10.4028/www.scientific.net/KEM.693.1046

Paper Titles

Experimental Study on the Wear of Single Crystal Diamond Tools in Ultra-Precision Cutting of Titanium Alloy
p.1015

Finite Element Analysis of SiCp/Al Model of Unit Cell during Ultrasonic Vibration Scratching
p.1022

Finite Element Analysis of Temperature Field in Vibration Milling
p.1030

Finite Element Deformation Analysis of Long Thin Cantilever Shape Parts in High Speed Ball End Milling of Titanium Alloy Ti-6Al-4V with PCD Tools at Various Tool Inclination Angles
p.1038

Finite Element Simulation of the Cutting Process for Inconel 718 Alloy Using a New Material Constitutive Model
p.1046

Finite Element Simulation on the Distribution of Discharge Gas in Hollow Cathode Plasma
p.1054

Heat Conduction in Coated Tools during Cutting Based on Finite Element Simulation
p.1061

Influence of Edge Preparation Parameters on the Cutting Edge in Drag Finishing
p.1067

Microfabrication and Characterization of Tool Embedded Ni-Chrome Thin Film Micro-Sensors for Cutting Force Measurement
p.1074

HomeKey Engineering MaterialsKey Engineering Materials Vol. 693Finite Element Simulation of the Cutting Process...

Finite Element Simulation of the Cutting Process for Inconel 718 Alloy Using a New Material Constitutive Model

Abstract:

Inconel 718 alloy is a typical difficult-to-cut material and widely used in the aerospace industry. Finite element simulation is an efficient method to investigate the cutting process, whereby a work material constitutive model plays an important role. In this paper, finite element simulation of the cutting process for Inconel 718 alloy using a new material constitutive model for high strain rates is presented. The effect of tool cutting edge radius on the cutting forces and temperature is then investigated with a view to facilitate cutting tool design. It is found that as the cutting edge radius increases, the characteristics of tool-work friction and the material removal mechanisms change, resulting in variation in cutting forces and temperature. It is shown that a smaller cutting edge radius is preferred to reduce the cutting forces and cutting temperature.

You might also be interested in these eBooks

Advanced Materials and Manufacturing Technology II

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 693)

Pages:

1046-1053

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.693.1046

Citation:

Cite this paper

Online since:

May 2016

Authors:

Xiang Yu Wang*, Chuan Zhen Huang, Jun Wang, Bin Zou, Guo Liang Liu, Han Lian Liu

Keywords:

Cutting Edge Radius, Finite Element Simulation, Inconel 718, Material Constitutive Model

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] D. Dudzinski, A. Devillez, A. Moufki, D. Larrouquère and V. Zerrouki, J. Vigneau: Int. J. Mach. Tools Manuf. Vol. 44 (2004), p.439–456.

DOI: 10.1016/s0890-6955(03)00159-7

Google Scholar

[2] A.V. Mitrofanov, V.I. Babitsky and V.V. Silberschmidt: J. Mater. Process. Technol. Vol. 153-154 (2004), p.233.

Google Scholar

[3] A.V. Mitrofanov, V.I. Babitsky and V.V. Silberschmidt: Comput. Mater. Sci. Vol. 32 (2005), p.463.

Google Scholar

[4] N. Ahmed, A.V. Mitrofanov, V.I. Babitsky and V.V. Silberschmidt: Mater. Sci. Eng. A. Vol. 424 (2006), p.318.

Google Scholar

[5] C. Hortig and B. Svendsen: J. Mater. Process. Technol. Vol. 186 (2007), p.66.

Google Scholar

[6] T. Özel: Proc. ASME 2009 Int. Manuf. Sci. Eng. Conf., 2009: p.1–6.

Google Scholar

[7] T. Özel, I. Llanos, J. Soriano and P. -J. Arrazola: Mach. Sci. Technol. Vol. 15 (2011), p.21.

Google Scholar

[8] S.P.F.C. Jaspers and J.H. Dautzenberg: J. Mater. Process. Technol. Vol. 122 (2002), p.322.

Google Scholar

[9] X. Wang, C. Huang, B. Zou, H. Liu, H. Zhu and J. Wang: Mater. Sci. Eng. A. Vol. 580 (2013), p.385.

Google Scholar