Key Engineering Materials

ISSN: 1662-9795

Main Themes

Volumes
Edited by: Yang Liu
Online since: June 2015
Description: In China, the amount of deteriorating bridges is increasing gradually, and the costs of maintenance, repair and rehabilitation of these bridges far exceed available budgets. Internationally, above issue also is paid more attention. To alleviate this issue, the bridge engineering profession continues to take positive steps towards developing more comprehensive bridge monitoring and management systems. Therefore, it is significant to combine some good works that have been done in this field, which is the original objective to introduce the recent research results in the fields of bridge health monitoring, bridge maintenance and safety in the mainland of China. This project encompasses some aspects of bridge health monitoring, maintenance and safety. Specifically, it deals with: bridge health monitoring; bridge repair and rehabilitation issues; bridge related safety and other implications.

648

Edited by: Josef Kasl and Dagmar Jandová
Online since: May 2015
Description: Collection of selected, peer reviewed papers from the 13th Contribution of Metallography to Solving of Production Trouble, June 17-19, 2014, Lázně Libverda, Czech Republic.
The 33 papers are grouped as follows:
I. Steels;
II. Alloys;
III. Surface Treatment and Powder Metallurgy;
VI. Welding and Creep Resistant Materials;
V. Methods of Research and Analyze;
IV. Failure Analysis

647

Edited by: Fei Tang
Online since: May 2015
Description: Collection of selected, peer reviewed papers from the 16th Annual Conference and 5th International Conference of the Chinese Society of Micro-Nano Technology (CSMNT 2014), August 31-September 3, 2014, Chengdu, China.
The 226 papers are grouped as follows:
Chapter 1: Materials and Technologies in the Scale of Micro and Nano;
Chapter 2: Micro/Nanofluids Research and Technologies;
Chapter 3: Measurements, Sensors and MEMS;
Chapter 4: Micro Actuators and Devices;
Chapter 5: Optics in the Scale of Micro and Nano;
Chapter 6: Energy Harvesting, Power Supply and Technologies for Fuel Cells;
Chapter 7: Bioresearch and Biomedical Engineering

645-646

Edited by: J. Gutierez, J.M. Barandiarán, Evangelos Hristoforou and D.S. Vlachos
Online since: May 2015
Description: These are the proceedings of the 4th International Conference on Materials and Applications for Sensors and Transducers, Bilbao, Spain. The collection covers a selection of 63 peer review papers covering up-to-date research result in the field. IC-MAST is an international annual held conference which tries to meet the needs for various types of sensors, particularly those ones which may be manufactured by low cost methods (i.e. hybrid sensors, smart specialization devices, particular applications not necessarily requiring integrated micro-nano technologies), covering all types of materials and physical effects.

644

Edited by: Sumio Hosaka
Online since: May 2015
Description: Collection of selected, peer reviewed papers from the 5th International Conference on Advanced Micro-Device Engineering 2013 (AMDE 2013), December 19, 2013, Kiryu, Japan.
The 28 papers are grouped as follows:
I. Micro- and Nano-Science and Technologies;
II. Photonic and Magnetic Materials and Devices; III. Electronics, Microelectronics and Communication;
IV. Novel Methods and Devices for Measurements;
V. Medical Science and Health Security

643

Edited by: Yunn-Lin Hwang, Jeng-Haur Horng and Chin-Chung Wei
Online since: April 2015
Description: Collection of selected, peer reviewed papers from the Selected, peer reviewed papers from the International Conference on Engineering Tribology Technology 2014 (ICETT 2014), November 21-23, 2014, Nantou, Taiwan.
The 62 papers are grouped as follows:
Chapter 1: Tribology Engineering and Applications

642

Edited by: Tomasz Tokarski
Online since: April 2015
Description: Collection of selected, peer reviewed papers from the International Conference of Non-Ferrous Metals - Processing and New Technologies, June 4-6, 2014, Wisła, Poland.
The 40 papers are grouped as follows:
Chapter 1: Materials and Related Industrial Technologies;
Chapter 2: Metalworking

641

Edited by: M. Karama, Karl Delbé and J. Denape
Online since: March 2015
Description: The main objectives of this special issue (consisting mainly of a selection of extended papers presented at 5th International Symposium on AirCraft Materials ACMA 2014) are to push the current limits in modeling and computation in response to industrial and society challenges. It is also to control the calculations and models in a framework that takes into account the major sources of uncertainty to optimize materials and structures. Particular attention is given to the modeling and validation of composite materials and structures.

640

Edited by: M. Merklein, J. Duflou, A. Leacock, F. Micari and H. Hagenah
Online since: March 2015
Description: Collection of selected, peer reviewed papers from the 16th International Conference on Sheet Metal (SheMet 2015), March 16-18, Erlangen-Nürnberg, Germany.
The 70 papers are grouped as follows:
Chapter 1: Keynote;
Chapter 2: Forming;
Chapter 3: Bending;
Chapter 4: Incremental Forming;
Chapter 5: Hot Stamping;
Chapter 6: Sheet-Bulk Metal Forming;
Chapter 7: Materials Testing;
Chapter 8: Modelling;
Chapter 9: Cutting and Joining;
Chapter 10: Planning;
Chapter 11: MatProFuture

639

Edited by: Antoniac Iulian, Albu Madalina, Sinescu Cosmin and Miculescu Marian
Online since: March 2015
Description: Collection of selected, peer reviewed papers from the the 6th International Conference “Biomaterials, Tissue Engineering & Medical Devices” (BiomMedD’2014), September 17-20, 2014, Constanța, România.
The 60 papers are grouped as follows:
Chapter 1: Biomaterials;
Chapter 2: Biomedical Engineering;
Chapter 3: Biomaterials and Technologies in Clinical Practice;
Chapter 4: Auxiliary Techniques and Tools in Biomedical Practice

638

Showing 121 to 130 of 508 Main Themes