Iron Carbon Masteralloy as Sintering Activator for Low Alloy Powder Metallurgy Steels

Abstract:

In real industrial environment there is always a difference between ideal theoretical condition and real production condition which bears the risk of producing defective or low quality parts. Getting closer to this ideal situation requires more effort and investment which tends to increase the production cost. In the P/M production lines, the sintering stage is one of the most critical processes. Maintaining an open continuous sintering furnace in an ideal condition is a challenge, and this issue gets more pronounced when using alloy powder containing oxygen-sensitive elements such as Cr or Mn which provide good hardenability at low cost but on the other hand form stable oxides that weaken the sintering contacts if they are not reduced properly. In the present study, using a carbon master alloy as a sintering enhancer in the sintering process of Cr-Mo alloyed powder compacts has been investigated. For clearly depicting the effect of carbon master alloy addition on carbon dissolution and deoxidation, sintering was done in argon as inert atmosphere to avoid other reducing agents such as H₂. The physical and mechanical properties of the sintered specimens were investigated, and thermal chemical analysis by DIL/MS and carbon/oxygen measurements were performed. The experiments showed that adding iron-carbon masteralloys promote the sintering processes such as reduction of oxides and carbon dissolution in the early stages of sintering, resulting in better properties after final sintering.

• Periodical: Materials Science Forum (Volume 1016)
• Pages: 561-567
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.1016.561
• Online since: January 2021
• Authors: Milad Hojati*, Christian Gierl-Mayer, Herbert Danninger
• Keywords: Carbon Dissolution, Ferrous Powders, Master Alloy, Oxygen, Reduction, Sintering, Thermal Analysis

References

[1] H. Danninger, et al., Dissolution of different graphite grades during sintering of PM steels. Materials Chemistry and Physics, 2001. 67(1): pp.72-77.

DOI: 10.1016/s0254-0584(00)00422-3

[2] J.R. Davis, K.M. Mills, S.R. Lampman, Properties and selection: irons, steels, and high-performance alloys. Metals handbook. Vol. 1. 1990: ASM International, Materials Park, Ohio 44073.

DOI: 10.31399/asm.hb.v01.9781627081610

[3] N.Dautzenberg, J.Hewing, Reaction Kinetics during Sintering of Mixed Alloyed Steels of Iron and Graphite Powders. Powder Metall. Int., 1977. 9: p. no.1, pp.16-19.

[4] Y.Tanaka, J.A. Lund, Catalytic Effect of Carbonates in Iron-Graphite Compacts. Powder Metallurgy Progress, 1988. 31: p. no.1, pp.45-51.

DOI: 10.1179/pom.1988.31.1.45

[5] Y.Tanaka, J.A. Lund, Alloying and Sintering in Iron-Graphite Compacts at 900°C. Powder Metall. Int., 1989. 18: p. no.6, pp.409-411.

[6] J. Park, et al., Complex effects of alloy composition and porosity on the phase transformations and mechanical properties of powder metallurgy steels. Powder Technology, 2015. 284.

DOI: 10.1016/j.powtec.2015.07.029

[7] D. Chasoglou, E. Hryha, and L. Nyborg, Effect of process parameters on surface oxides on chromium-alloyed steel powder during sintering. Materials Chemistry and Physics, 2013. 138(1): pp.405-415.

DOI: 10.1016/j.matchemphys.2012.11.074

[8] M.W. Wu, et al., The effects of alloying elements and microstructure on the impact toughness of powder metal steels. Materials Science and Engineering: A, 2012. 538: pp.135-144.

DOI: 10.1016/j.msea.2011.12.113

[9] D. Shanmugasundaram, and R. Chandramouli, Tensile and impact behaviour of sinter-forged Cr, Ni and Mo alloyed powder metallurgy steels. Materials & Design, 2009. 30(9): pp.3444-3449.

DOI: 10.1016/j.matdes.2009.03.020

[10] M. Campos, L. Blanco, and J. Torralba, Thermalanalysis of prealloyed Fe–3Cr–0.5Mo sintered steel. Journal of Thermal Analysis and Calorimetry - J THERM ANAL CALORIM, 2006. 84: pp.483-487.

DOI: 10.1007/s10973-005-6991-2

[11] N. Candela, , et al., Influence of microstructure on mechanical properties of molybdenum alloyed P/M steels. Journal of Materials Processing Technology, 2005. 168(3): pp.505-510.

DOI: 10.1016/j.jmatprotec.2004.02.066

[12] O. Bergman, Influence of oxygen partial pressure in sintering atmosphere on properties of Cr-Mo prealloyed powder metallurgy steel. Powder Metallurgy, 2007. 50(3): pp.243-249.

DOI: 10.1179/174329007x205073

[13] M. Dlapka, et al., Reaction of Unalloyed and Cr-Mo Alloyed Steels with Nitrogen from the Sintering Atmosphere. Powder Metallurgy Progress, 2016. 16.

DOI: 10.1515/pmp-2016-0007

[14] H. Danninger, R. De Oro Calderon, and C. Gierl-Mayer, Oxygen Transfer Reactions during Sintering of Ferrous Powder Compacts. Advanced Engineering Forum, 2018. 27: pp.3-13.

DOI: 10.4028/www.scientific.net/aef.27.3

[15] C. Gierl-Mayer, R. de Oro Calderon, and H. Danninger, The Role of Oxygen Transfer in Sintering of Low Alloy Steel Powder Compacts: A Review of the Internal Getter, Effect. JOM, 2016. 68(3): pp.920-927.

DOI: 10.1007/s11837-016-1819-z