Investigation into the Distribution of Erosion-Corrosion in the Furnace Tubes of Oil Refineries

Abstract:

Crude oil is one of the most important sources of energy in the world. To extract its multiple components, we need oil refineries. Refineries consist of multiple parts, including heat exchangers, furnaces, and others. It is known that one of the initial operations in the refineries is the process of gradually raising the temperature of crude oil to 370 degrees centigrade or higher. Hence, in this investigation the focus is on the furnaces and the corrosion in their tubes. The investigation was accomplished by reading the thickness of the tubes for the period from 2008 to 2020 with a test in every two year, had passed from their introduction into the work. Where the thickness of more than one point was measured on each tube in the same row and the corrosion rate was extracted for three furnaces, starting from the area of ​​heat transfer by radiation to the heat transfer area of ​​the convection in three different operating units. It was found that the highest percentage corrosion value between the standard tube thickness and the thickness of conduction position was 37% with the conduction zone, and 31% with radiation zone. There, the tubes specification was tested. Five percent Cr-0.5 Moly and the temperature of radiation zone was 578 °C to 613 °C and the stack temperature was 410 °C to 450 °C. So, the results show that the maximum erosion occur at the convection zone.

• Periodical: Materials Science Forum (Volume 1039)
• Pages: 165-181
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.1039.165
• Online since: July 2021
• Authors: Muhsin Jaber Jweeg, Karrar Ibrahim Mohammed, Moneer H. Tolephih, Muhannad Al-Waily*
• Keywords: Corrosion Pipe, Distribution of Erosion, Furnace Tubes, Oil Refineries, Pipe Line

References

[1] Ugya A Y, T S Imam and S M Tahir, Emerging Trends in the Remediation of Pollution, Lambert Publishing Company, (2016).

[2] Mir Esmaeil Masoumi and Zahra Izakmehri, Improving of Refinery Furnaces Efficiency Using Mathematical Modeling, International Journal of Modeling and Optimization, 1, 1 (2011).

DOI: 10.7763/ijmo.2011.v1.14

[3] Jianyang Xie and Peter M Walsh, Erosion-Corrosion of Carbon Steel By Products of Coal Combustion, Wear journal, 186–187, Part 1 (1995) 256–265.

DOI: 10.1016/0043-1648(95)07168-7

[4] E G Plett, A C Alkidas, R E Shrader and M Summerfield, Erosion of Metals by High Pressure Combustion Gases Inert and Reactive Erosion, Journal of Heat Transfer, 97, Part 1 (2010) 110–115.

DOI: 10.1115/1.3450257

[5] M R Ismail, Evaluating the Dynamical Behavior and Stability of Pipes Conveying Fluid, PhD Thesis Al-Nahrain University, Mechanical Engineering (2011).

[6] K I Mohammed, Hassan Mansour Raheem, Radhwan Hussein Abdulzhraa Al-Sagheer and Hayder Al-Sarraf, Detection of Faults in Pipe That Transmits Crude Oil by Vibration Sensing: Analytically and Experimentally, International Conference on Mechanical and Aerospace Engineering (2018).

[7] Karrar Ibrahim Mohammed and Younus Mohammed Younus, Experimental Investigation into the Effect of Erosion and Corrosion in Pipes Conveying Fluid on its Frequencies, International journal of energy and environment, 10, 1 (2019) 25–32.

[8] Xiangdong Men ,Fenghe Tao, Lin Gan and Fang Zhao, Erosion Behavior of Ni-Based Coating under High-Speed Hot Airflow, Surface Engineering, 35 (2019) 710–718.

DOI: 10.1080/02670844.2019.1573343

[9] ASTM A213/A213M-19a, Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes, ASTM International, West Conshohocken, PA (2019).

DOI: 10.1520/a0213_a0213m-21b

[10] Muhsin J Jweeg, Application of Finite Element Analysis to Rotating Fan Impellers, Doctoral Thesis, Aston University (1983).

[11] Muhsin J Jweeg and S Z Said, Effect of Rotational and Geometric Stiffness Matrices on Dynamic Stresses and Deformations of Rotating Blades, Journal of the Institution of Engineers (India): Mechanical Engineering Division, 76 (1995) 29–38.

[12] Ghaith G Hameed, Muhsin J Jweeg and Ali Hussein, Springback and Side Wall Curl of Metal Sheet in Plain Strain Deep Drawing, Research Journal of Applied Sciences, 4, 5 (2009).

[13] Muhsin J Jweeg, Ali S Hammood and Muhannad Al-Waily, A Suggested Analytical Solution of Isotropic Composite Plate with Crack Effect, International Journal of Mechanical & Mechatronics Engineering, 12, 5 (2012).

[14] Muhannad Al-Waily, Alaa Abdulzahra Deli, Aziz Darweesh Al-Mawash and Zaman Abud Almalik Abud Ali, Effect of Natural Sisal Fiber Reinforcement on the Composite Plate Buckling Behavior, International Journal of Mechanical & Mechatronics Engineering, 17, 1 (2017).

[15] Mohsin Abdullah Al-Shammari, Emad Q Hussein and Ameer Alaa Oleiwi, Material Characterization and Stress Analysis of a Through Knee Prosthesis Sockets, International Journal of Mechanical & Mechatronics Engineering, 17, 6 (2017).

[16] Kadhim K Resan, Abbas A Alasadi, Muhannad Al-Waily and Muhsin J Jweeg, Influence of Temperature on Fatigue Life for Friction Stir Welding of Aluminum Alloy Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 2 (2018).

[17] Muhsin J Jweeg, Zaid S Hammoudi and Bassam A Alwan, Optimised Analysis, Design, and Fabrication of Trans-Tibial Prosthetic Sockets, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012058

[18] Mahmud Rasheed Ismail, Muhannad Al-Waily and Ameer A Kadhim, Biomechanical Analysis and Gait Assessment for Normal and Braced Legs, International Journal of Mechanical & Mechatronics Engineering, 18, 3 (2018).

[19] Saif M Abbas, Ayad M Takhakh, Mohsin Abdullah Al-Shammari and Muhannad Al-Waily, Manufacturing and Analysis of Ankle Disarticulation Prosthetic Socket (SYMES), International Journal of Mechanical Engineering and Technology, 9, 7 (2018) 560–569.

[20] Ragad Aziz Neama, Maher A R Sadiq Al-Baghdadi and Muhannad Al-Waily, Effect of Blank Holder Force and Punch Number on the Forming Behavior of Conventional Dies, International Journal of Mechanical & Mechatronics Engineering, 18, 4 (2018).

[21] Jumaa S Chiad, Muhannad Al-Waily and Mohsin Abdullah Al-Shammari, Buckling Investigation of Isotropic Composite Plate Reinforced by Different Types of Powders, International Journal of Mechanical Engineering and Technology, 9, 9 (2018) 305–317.

[22] Mohsin Abdullah Al-Shammari and Sahar Emad Abdullah, Stiffness to Weight Ratio of Various Mechanical and Thermal Loaded Hyper Composite Plate Structures, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012051

[23] Muhsin J Jweeg, Muhannad Al-Waily, Ahmed K Muhammad and Kadhim K Resan, Effects of Temperature on the Characterisation of a New Design for a Non-Articulated Prosthetic Foot, IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, 433 (2018).

DOI: 10.1088/1757-899x/433/1/012064

[24] Ahmed Khaleel Abdulameer and Mohsin Abdullah Al-Shammari, Fatigue Analysis of Syme's Prosthesis, International Review of Mechanical Engineering, 12, 3 (2018).

[25] Ehab N Abbas, Muhsin J Jweeg and Muhannad Al-Waily, Analytical and Numerical Investigations for Dynamic Response of Composite Plates Under Various Dynamic Loading with the Influence of Carbon Multi-Wall Tube Nano Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 6 (2018) 1–10.

[26] H J Abbas, M J Jweeg, Muhannad Al-Waily and Abbas Ali Diwan, Experimental Testing and Theoretical Prediction of Fiber Optical Cable for Fault Detection and Identification, Journal of Engineering and Applied Sciences, 14, 2 (2019) 430–438.

DOI: 10.36478/jeasci.2019.430.438

[27] Yousuf Jamal Mahboba and Mohsin Abdullah Al-Shammari, Enhancing Wear Rate of High-Density Polyethylene (HDPE) by Adding Ceramic Particles to Propose an Option for Artificial Hip Joint Liner, IOP Conference Series: Materials Science and Engineering, 561 (2019).

DOI: 10.1088/1757-899x/561/1/012071

[28] Suhair Ghazi Hussein, Mohsin Abdullah Al-Shammari, Ayad M Takhakh and Muhannad Al- Waily, Effect of Heat Treatment on Mechanical and Vibration Properties for 6061 and 2024 Aluminum Alloys, Journal of Mechanical Engineering Research & Developments, 43, 1 (2020).

[29] Marwah Ali Husain and Mohsin Abdullah Al-Shammari, Analytical Solution of Free Vibration Characteristics of Partially Circumferential Cracked Cylindrical Shell, Journal of Mechanical Engineering Research and Developments, 43, 3 (2020) 442–454.

[30] Muhannad Al-Waily, Mohsin Abdullah Al-Shammari and Muhsin J Jweeg, An Analytical Investigation of Thermal Buckling Behavior of Composite Plates Reinforced by Carbon Nano Particles, Engineering Journal, 24, 3 (2020).

DOI: 10.4186/ej.2020.24.3.11

[31] Ehab N Abbas, Muhsin J Jweeg and Muhannad Al-Waily, Fatigue Characterization of Laminated Composites used in Prosthetic Sockets Manufacturing, Journal of Mechanical Engineering Research and Developments, 43, 5 (2020) 384–399.

[32] Ekhlas Edan Kader, Akram Mahdi Abed and Mohsin Abdullah Al-Shammari, Al2O3 Reinforcement Effect on Structural Properties of Epoxy Polysulfide Copolymer, Journal of Mechanical Engineering Research and Developments, 43, 4 (2020) 320–328.

[33] Sadiq emad Sadiq, Sadeq Hussein Bakhy and Muhsin Jaber Jweeg, Effects of Spot Welding Parameters on the Shear Characteristics of Aluminum Honeycomb Core Sandwich Panels in Aircraft Structure, Test Engineering and Management, 83 (2020) 7244–7255.

DOI: 10.1088/1757-899x/928/2/022126

[34] Najdat A Mahmood, Muhsin J Jweeg and Mumtaz Y Rajab, Investigation of Partially Pressurized Thick Cylindrical Shells, Modelling, simulation & control B. AMSE Press, 25, 3 (1989) 47–64.

[35] Muhannad Al-Waily and Zaman Abud Almalik Abud Ali, A Suggested Analytical Solution of Powder Reinforcement Effect on Buckling Load for Isotropic Mat and Short Hyper Composite Materials Plate, International Journal of Mechanical & Mechatronics Engineering, 15, 4 (2015).

[36] Muhannad Al-Waily, Maher A R Sadiq Al-Baghdadi and Rasha Hayder Al-Khayat, Flow Velocity and Crack Angle Effect on Vibration and Flow Characterization for Pipe Induce Vibration, International Journal of Mechanical & Mechatronics Engineering, 17, 5 (2017).

[37] Ameer A Kadhim, Muhannad Al-Waily, Zaman Abud Almalik Abud Ali, Muhsin J Jweeg and Kadhim K Resan, Improvement Fatigue Life and Strength of Isotropic Hyper Composite Materials by Reinforcement with Different Powder Materials, International Journal of Mechanical & Mechatronics Engineering, 18, 2 (2018).

[38] Rasha Hayder Al-Khayat, Maher A R Sadiq Al-Baghdadi, Ragad Aziz Neama and Muhannad Al-Waily, Optimization CFD Study of Erosion in 3D Elbow During Transportation of Crude Oil Contaminated with Sand Particles, International Journal of Engineering & Technology, 7, 3 (2018) 1420–1428.

DOI: 10.14419/ijet.v7i3.14180

[39] Mohsin Abdullah Al-Shammari and Muhannad Al-Waily, Analytical Investigation of Buckling Behavior of Honeycombs Sandwich Combined Plate Structure, International Journal of Mechanical and Production Engineering Research and Development, 8, 4 (2018) 771–786.

DOI: 10.24247/ijmperdaug201883

[40] Saif M Abbas, Kadhim K Resan, Ahmed K Muhammad and Muhannad Al-Waily, Mechanical and Fatigue Behaviors of Prosthetic for Partial Foot Amputation with Various Composite Materials Types Effect, International Journal of Mechanical Engineering and Technology, 9, 9 (2018).

[41] Mahmud Rasheed Ismail, Zaman Abud Almalik Abud Ali and Muhannad Al-Waily, Delamination Damage Effect on Buckling Behavior of Woven Reinforcement Composite Materials Plate, 2018, International Journal of Mechanical & Mechatronics Engineering, 18, 5 (2018).

[42] Worood Hussein and Mohsin Abdullah Al-Shammari, Fatigue and Fracture Behaviours of FSW and FSP Joints of AA5083-H111 Aluminium Alloy, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012055

[43] Muhsin J Jweeg, Kadhim K Resan, Esraa A Abbod and Muhannad Al-Waily, Dissimilar Aluminium Alloys Welding by Friction Stir Processing and Reverse Rotation Friction Stir Processing, IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, 454 (2018).

DOI: 10.1088/1757-899x/454/1/012059

[44] Marwah Mohammed Abdulridha, Nasreen Dakel Fahad, Muhannad Al-Waily and Kadhim K Resan, Rubber Creep Behavior Investigation with Multi Wall Tube Carbon Nano Particle Material Effect, International Journal of Mechanical Engineering and Technology, 9, 12 (2018).

[45] Mohsin Abdullah Al-Shammari, Lutfi Y Zedan and Akram M Al-Shammari, FE Simulation of Multi-Stage Cold Forging Process for Metal Shell of Spark Plug Manufacturing, 1st International Scientific Conference of Engineering Sciences, 3rd Scientific Conference of Engineering Science (2018).

DOI: 10.1109/isces.2018.8340555

[46] Mohsin Abdullah Al-Shammari, Experimental and FEA of the Crack Effects in a Vibrated Sandwich Plate, Journal of Engineering and Applied Sciences, 13, 17 (2018).

[47] Muhannad Al-Waily, Emad Q Hussein and Nibras A Aziz Al-Roubaiee, Numerical Modeling for Mechanical Characteristics Study of Different Materials Artificial Hip Joint with Inclination and Gait Cycle Angle Effect, Journal of Mechanical Engineering Research & Developments, 42, 4 (2019) 79–93.

DOI: 10.26480/jmerd.04.2019.79.93

[48] Muhsin J Jweeg, Abdulkareem Abdulrazzaq Ahumdany and Ali Faik Mohammed Jawad, Dynamic Stresses and Deformations Investigation of the Below Knee Prosthesis using CT- Scan Modeling, International Journal of Mechanical & Mechatronics Engineering, 19, 1 (2019).

[49] Mohsin Abdullah Al-Shammari, Qasim H Bader, Muhannad Al-Waily and A M Hasson, Fatigue Behavior of Steel Beam Coated with Nanoparticles under High Temperature, Journal of Mechanical Engineering Research and Developments, 43, 4 (2020) 287–298.

[50] Esraa A Abbod, Muhannad Al-Waily, Ziadoon M R Al-Hadrayi, Kadhim K Resan and Saif M Abbas, Numerical and Experimental Analysis to Predict Life of Removable Partial Denture, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Engineering and Advanced Technology, 870 (2020).

DOI: 10.1088/1757-899x/870/1/012149

[51] Hussein I Mansoor, Mohsin Al-shammari and Amjad Al-Hamood, Theoretical Analysis of the Vibrations in Gas Turbine Rotor, IOP Conference Series: Materials Science and Engineering, 3rd International Conference on Engineering Sciences, 671 (2020).

DOI: 10.1088/1757-899x/671/1/012157

[52] Muhannad Al-Waily, Iman Q Al Saffar, Suhair G Hussein and Mohsin Abdullah Al-Shammari, Life Enhancement of Partial Removable Denture made by Biomaterials Reinforced by Graphene Nanoplates and Hydroxyapatite with the Aid of Artificial Neural Network, Journal of Mechanical Engineering Research and Developments, 43, 6 (2020) 269–285.

[53] Muhsin J Jweeg, Salah N Alnomani and Salah K Mohammad, Dynamic Analysis of a Rotating Stepped Shaft with and Without Defects, IOP Conference Series: Materials Science and Engineering, 3rd International Conference on Engineering Sciences, 671 (2020).

DOI: 10.1088/1757-899x/671/1/012004

[54] Hussein I Mansoor, Mohsin Abdullah Al-shammari, Amjad Al-Hamood, Experimental Analysis of Cracked Turbine Rotor Shaft using Vibration Measurements, Journal of Mechanical Engineering Research and Development, 43, 2 (2020) 294–304.

[55] S E Sadiq, S H Bakhy and M J Jweeg, Crashworthiness Behavior of Aircraft Sandwich Structure with Honeycomb Core under Bending Load, IOP Conference Series: Materials Science and Engineering (2020).

DOI: 10.1088/1757-899x/881/1/012046

[56] Ehab N Abbas, Muhannad Al-Waily, Tariq M Hammza and Muhsin J Jweeg, An Investigation to the Effects of Impact Strength on Laminated Notched Composites used in Prosthetic Sockets Manufacturing, IOP Conference Series: Materials Science and Engineering, 2nd International Scientific Conference of Al-Ayen University, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022081

[57] Sadiq Emad Sadiq, Muhsin J Jweeg and Sadeq H Bakhy, The Effects of Honeycomb Parameters on Transient Response of an Aircraft Sandwich Panel Structure, IOP Conference Series: Materials Science and Engineering, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022126

[58] Muhannad Al-Waily, Moneer H Tolephih and Muhsin J Jweeg, Fatigue Characterization for Composite Materials used in Artificial Socket Prostheses with the Adding of Nanoparticles, IOP Conference Series: Materials Science and Engineering, 2nd International Scientific Conference of Al-Ayen University, 928 (2020).

DOI: 10.1088/1757-899x/928/2/022107

[59] Muhannad Al-Waily, Iman Q. Al Saffar, Suhair G. Hussein and Mohsin Abdullah Al-Shammari, Life Enhancement of Partial Removable Denture made by Biomaterials Reinforced by Graphene Nanoplates and Hydroxyapatite with the Aid of Artificial Neural Network, Journal of Mechanical Engineering Research and Developments, 43, 6 (2020) 269-285.

[60] Ehab N. Abbas, Muhsin J. Jweeg and Muhannad Al-Waily, Fatigue Characterization of Laminated Composites used in Prosthetic Sockets Manufacturing, Journal of Mechanical Engineering Research and Developments, 43, 5 (2020) 384-399.

[61] Esraa A. Abbod, Muhannad Al-Waily, Ziadoon M. R. Al-Hadrayi, Kadhim K. Resan and Saif M. Abbas, Numerical and Experimental Analysis to Predict Life of Removable Partial Denture, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Engineering and Advanced Technology, 870 (2020).

DOI: 10.1088/1757-899x/870/1/012149

[62] Muhannad Al-Waily, Mohsin Abdullah Al-Shammari and Muhsin J. Jweeg, An Analytical Investigation of Thermal Buckling Behavior of Composite Plates Reinforced by Carbon Nano Particles, Engineering Journal, 24, 3 (2020).

DOI: 10.4186/ej.2020.24.3.11

[63] Sadeq H. Bakhy and Muhannad Al-Waily, Development and Modeling of a Soft Finger in Robotics Based on Force Distribution, Journal of Mechanical Engineering Research and Developments, 44, 1 (2021) 382-395.

[64] Tammam Salim Naji Aswad, Mohd Azahari Bin Razali and Muhannad Al-Waily, Numerical Study of the Shape Obstacle Effect on Improving the Efficiency of Photovoltaic Cell, Journal of Mechanical Engineering Research and Developments, 44, 2 (2021) 209-224.

[65] Hayder Zaher Abdalikhwa, Mohsin Abdullah Al-Shammari, Emad Qasem Hussein, Characterization and Buckling Investigation of Composite Materials to be used in the Prosthetic Pylon Manufacturing, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012170

[66] Muhsin J. Jweeg, H. A. Hamzah, Muhannad Al-Waily, Mohsin Abdullah Al-Shammari, A Finite Element Simulation of Nano Effects on Stress Distribution in a Below Knee Prosthetic, 4th International Conference on Engineering Sciences, IOP Conference Series: Materials Science and Engineering, 1067 (2021).

DOI: 10.1088/1757-899x/1067/1/012141

[67] Mohammed Hussein Kadhim Aljaberi, Maher AR Sadiq Al-Baghdadi, Muhannad Al-Waily, M Mohammadi-Aghdam, Taha Goudarzi, Numerical Investigation of Mechanical Behavior for Lattice Structure with Effect of Different Nanomaterial Types, IOP Conference Series: Materials Science and Engineering, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012172

[68] Emad Kadum Njim, Muhannad Al-Waily, Sadeq H Bakhy, A Critical Review of Recent Research of Free Vibration and Stability of Functionally Graded Materials of Sandwich Plate, IOP Conference Series: Materials Science and Engineering, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012081

[69] Rasha M Hussien and Mohsin Abdullah Al-Shammari, Optimization of Friction Stir Welded Aluminium Plates by the New Modified Particle Swarm Optimization, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012156

[70] Emad Kadum Njim, Muhannad Al-Waily, Sadeq H. Bakhy, A Review of the Recent Research on the Experimental Tests of Functionally Graded Sandwich Panels, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 420-441.

DOI: 10.1016/j.matpr.2021.03.235

[71] Zaman Abud Almalik Abud Ali, Ameer A. Kadhim, Rasha Hayder Al-Khayat, Muhannad Al-Waily, Review Influence of Loads upon Delamination Buckling in Composite Structures, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 392-406.

[72] Ameer A. Kadhim, Esraa A. Abbod, Ahmed K. Muhammad, Kadhim K. Resan, Muhannad Al-Waily, Manufacturing and Analyzing of a New Prosthetic Shank with Adapters by 3D Printer, Journal of Mechanical Engineering Research and Developments, 44, 3 (2021) 383-391.

[73] Saddam K Al-Raheem, Muhsin J Jweeg, Abdul kareem F Hassan, Design and Construction of Device for Rubber Material Fatigue Test, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012173

[74] Mohammed S Jabbar1 , Muhsin J Jweeg2 and Adnan I mohammed, Numerical and Experimental Study of Elastic Recovery in Deep Drawing of Low Carbon and Galvanized Steel Sheet Conical Products, IOP Conference Series: Materials Science and Engineering, 1st International Conference on Sustainable Engineering and Technology, 1094 (2021).

DOI: 10.1088/1757-899x/1094/1/012155

[75] M A Al-Baghdadi, K K Resan and Muhannad Al-Waily, CFD Investigation of the Erosion Severity In 3D Flow Elbow During Crude Oil Contaminated Sand Transportation, The 1st International Scientific Conference of Nanotechnology and Advanced Materials in Petroleum & Gas Industry, 3–4 May 2017, Engineering and Technology Journal, 35, Part A, 9 (2017).

DOI: 10.30684/etj.35.9a.10